= ignition timer switched off | Blaupunkt TCM 169 specification

Programming with DSC Radio, Cassette, Changer (optional)

You cannot alter the programming for important DSC settings unless you have entered the access code first (refer to the DSC menu item “CHANGE ACCESS- CODE”).

LOUDNESS

Boosts low frequencies for more bass, es- pecially at low volume.

LOUD 1 - minimum boost LOUD 6 - maximum boost

Enter the original code (in this case “0000”) and press OK.

Enter the new code, press OK. Enter the new code once again, press OK.

IGNITION TIMER

RadioDEUTSCH

/ Select function

<</ >> Make setting

MASTER RESET

This menu item will appear only if a Key- Card is inserted.

Important!

This function will reset all of the settings in the DSC menu including the telephone menu to the factory default settings.

All of the trained KeyCards and SIM cards will be deleted, except for the KeyCard cur- rently in the unit.

If this menu item is selected, it will be nec- essary to enter the access code after OK. Enter the access code, press OK.

The display will show “MASTER RESET?”: Press CL to cancel this function, press OK to reset all of the settings to the default set- tings.

CHANGE ACCESSCODE

The access code is used to access the im- portant DSC menu items (also for telephone operation). At the factory, this code is set to “0000”.

If you would like to alter it be sure to make

a note of the new code!

Use this setting to ensure that the car radio will play for a maximum of 90 minutes after the ignition has been switched off.

0 = ignition timer switched off.

AUXILIARY SOURCE

This menu item will not appear if a CD changer (A 05 or A 06) has been connected to the system.

The default setting is “AUXILIARY SOURCE OFF”.

If an external piece of equipment is connect- ed to the system, this setting must be switched to “AUXILIARY SOURCE ON”.

VARIOCOLOUR

Adjusts the colour of the display illumina- tion to the dashboard illumination.

green

....................................................''

red

KEY TONE

After a key is pressed, a short beep is emit- ted as confirmation.

Set volume from 0 to 9 (0 = off).

ENGLISHTelefon

TelephoneRadio

91

Image 27

Blaupunkt TCM 169 Programming with DSC Radio, Cassette, Changer optional, = ignition timer switched off

Contents

Monte Carlo TCM Remote control RCT 07 optional Contents Radio, Cassette, Changer Option Contents Telephone General information Safety standardsSafety information Important information Emergency calls Using the telephone while drivingUsing the telephone in critical areas Important information Accessories Installation International telephone informa- tion Guarantee KeyCard and SIM card Basic informationStarting up the Radiophone Train KeyCard/SIM cards Training or replace KeyCard/ SIM card using DSCKeyCard and SIM card Removing the KeyCard/SIM card Care of your KeyCard/SIM card DSC learn modeDisplaying the radio pass data Optical warning of anti-theft protection Switching the radio on when the ig- nition is switched off On/off VolumeSwitching the unit on/off with the KeyCard Switching the unit on/off via the ig- nition Eject cassette Track switchSRC Source TS / BND AF / # Cassette loading slotStoring radio stations Recalling stored radio stations -Se Cassette operation Changer operation optional = MIXDisplay Radio operation a Tape operation Flashing card tongueStop this function by pressing or the opposite button Corresponding function must be activated Additional rocker switch functionsAdditional settings possible with AUD DSC mode C ME Unit Radio, tape deck, CD changer optional, auxiliary source Audio modeAF Alternative Frequency REG regional programme Selecting a waveband Station tuningRadio operation with RDS Radio Data System Entering the frequency directly Storing radio stations Scrolling through the broadcast- ing networks FM only Selecting the seek-tuning sensi- tivity Switching from stereo to mono FM onlyRecalling stored radio stations Traffic programme station reception with RDS-EON Switching traffic announcement priority on/offAutomatic seek tuning start Switching off the beep tone Operating the cassette deck Care instructions Operating the cassette deckTape equalisation Dolby B NR Switching CD changer operation on CD changer operation optionalSelecting the CD and the track Store CancelSelect Alter Programming with DSC Radio, Cassette, Changer optional = ignition timer switched off Music/voice is switched off Cards can only be programmed with the help of the DSC menuOn All of the menu items are available End DSC programming/save changes You can choose among the following oper- ating modes Overview of the DSC default settings Telephone operation Reactivating the SIM card Operating the telephonePIN code Inserting the SIM card/ entering your PIN code Do not hang up until you are told to do so Operating the telephoneMaking your first telephone call GSM emergency calls Selection buttons Quick reference for using the telephoneVolume On/Off Telephone-book menu Enter PIN code Setup menu/Call menuTo switch back to the telephone mode Press briefly Displays Radio menu @ Rocker switch Save telephone numbers and names Using the telephoneGSM network service area Switching to telephone mode Dialling a telephone number Using the telephone Save telephone numbers from the note- pad Redial functionAnswering/ending a call Automatic Broker’s call/hold Call waiting 2nd caller International calls Making telephone calls using the handset special accessorySetting up a conference call Conference calls Tip How to place telephone calls in foreign countriesHow to receive calls Teleph. number Blaupunkt You enter +49512149 107 Phone book menu Phone book menu How to enter a name/text Finding an entry by name Prevent access Show my phone numberCheck capacity Add entry Finding an entry by positionAltering, deleting, moving or copying the entry End DSC Press CL, the altered setting will not be storedProgramming with DSC Telephone Store/confirm 113 Programming with DSC Telephone -Setup menuProgramming in the setup menu Select the setup menu by pressing Automatic redial Ringing tone volume Automatic answer Operating modeHands-free volume Handset volume Call meter format SMS tone Entered Audible call timerSet charge parameters PIN code Be sure to make a note of the new code if you change it Alter access codeFollowing settings will be deleted External alarm Hands-free operation is possible on all four channels Overview of the basic factory settings in the set-up menuExtended menu Ring signal Hands-free channel TA during call 119 Press CL, the new setting will not be storedProgramming with DSC Telephone -Call menu Programming in the Call Menu Press OK You can display the message by press- ing Call mailbox Received SMS messagesSelecting the message Reading messages Calling the sender or another telephone Sending SMS messagesSender Network selection Cell Broadcast Call meters Call forwardingCall barring Fixed dial numbers Phone lock Closed user group Overview of the basic factory settings in the call menu Glossary Telephone SpecificationsAmplifier Tuner Index Index Service numbers 042 175 873Bosch Gruppe