Manuals
/
Bosch Appliances
/
Computer Equipment
/
Webcam
Bosch Appliances
3122 475 22015en manual Integrus Installation and User Instructions
Models:
3122 475 22015en
1
6
67
67
Download
67 pages
5.8 Kb
3
4
5
6
7
8
9
10
<
>
Troubleshooting
Specification
Install
Using the configuration menu
Connecting the DCN system
Setup Back
Charging procedure
View fault status
Signal Processing
NiMH Battery Pack
Page 6
Image 6
INTEGRUS
Installation and User Instructions
Bosch Security Systems
2005-04
3122 475 22015en
Page 5
Page 7
Page 6
Image 6
Page 5
Page 7
Contents
Integrus
Important Safeguards
Table of contents
Integrus Installation and User Instuctions Table of contents
Bosch Security Systems 2005-04 3122 475 22015en
Integrus Installation and User Instructions
System description and planning
System overview
IR radiation
Signal Processing
System technology
Quality modes
Directional sensitivity of the receiver
Aspects of infra-red distribution systems
Carriers and channels
Footprint of the radiator
Ambient lighting
Radiator mounted at 45 to the ceiling
11 Infra-red signal blocked by a person in front
Positioning the radiators
14 Combination of several reflected signals
Overlapping footprints and multipath effects
Planning an Integrus infra-red radiation system
Rectangular footprints
Planning radiators
Cabling
Setting the radiator delay switches
System with one transmitter
20m
System with two or more transmitters in one room
Calculation of the master-to-slave signal delays
Testing the coverage area
Interference from IR systems
Integrus Transmitters
Description
Audio interface modules
Integrus DCN interface module
Mounting an interface module in the transmitter housing
Interface module slot cover
Upgrading an LBB4502/xx to an INT-TX
Removing the main PCB and the rear panel
Installation of the INT-TXK
Removing the main PCB and the rear panel steps 1
Installation of the INT-TXK steps 1
Connecting other external audio sources
Connecting the DCN system
Connecting the DCN Next Generation
Connections
Connecting an emergency signal
Connecting to another transmitter
Using the configuration menu
Overview
To jump to a sub-menu
Navigate through the menu
To navigate through the Main menu
To navigate through a sub-menu
Examples
To jump back from a sub-menu to an item of the Main menu
Example 1 Disable carrier 2. See also section
Turn to move the cursor
Required channel num
Setup Back
Main menu
Configuration and operation
Start-up
View transmitter status
View fault status
DCN
Set monitoring options
View version information
Set transmission mode
Set network mode
Set number of channels
Set channel quality and assign inputs to channels
Per Channel Settings
Set channel names
Disable or enable carriers
View carrier assignments
Configure auxiliary inputs
Per Input Sensitivity settings
Enable / disable IR-monitoring
Enable / disable headphone output
Set sensitivity of the inputs
Reset all options to factory default values
Choose transmitter name
Medium and High Power Radiators
Integrus Radiators
Description
Radiator status indication
Mounting the radiators
Attaching the suspension bracket
Mounting on a floor stand
Wall mounting
Connecting radiators to the transmitter
Ceiling mounting
Mounting on horizontal surfaces
Low Power Wide Beam Radiator
Using the output power selection switch
Mounting the Radiator
Limitations
Integrus Receivers
Description
Reception test mode
Receiver headphones
Operation
Integrus Charging Units
LBB 4560 Charging unit
Charging procedure
Wall mounting the charging cabinet
Troubleshooting
Integrus Installation and User Instructions Troubleshooting
Technical Data
System Specification
Medium and High Power Radiators
Radiators and Accessories
Transmitter Upgrade Kit range
Transmitters and Modules
NiMH Battery Pack
Receivers, Battery Packs and Charging Units
Low Power Wide Beam Radiator
Wall Mounting Bracket
Connection details
Guaranteed rectangular footprints
Angle
Product index