D9210B

Installation

3.2.3Mounting

Do not install or replace a D9210B while it is connected to live power circuits. The D9210B should be powered down until it is ready to be tested.

3.2.3.1D9210BLC

1.Mount the D8103, D8109 or D8108A enclosure on a flat service.

2.Install another D9210LC to the mounting skirt (optional) prior to step 3.

3.Hang the mounting skirt in the enclosure by aligning the rectangular tabs of the enclosure with the rectangular knockouts on the mounting skirt.

4.Insert the #6x3/8 in. screw on the bottom tab of the mounting skirt and tighten 1/4 turn to seat it. This completes the mounting of the skirt in the enclosure.

3.2.3.2D9210B

1.Remove the cover of the D9210B by loosening the two cover screws.

2.Remove the required knockouts prior to replacing the cover.

3.Mark the holes provided for mounting the bottom half of the unit to a wall or ceiling.

4.Screw the provided screws in to the marked service and allow a 0.25 in. (6.4 mm) gap between the surface and bottom of the screw.

5.Hang the unit and secure the screws. Replace the cover and cover screws.

3.2.3.3D9210BC

1.The unit can be installed in a D8103, D8109 or D8108A enclosure by matching the three plastic mounting anchors to the three hole foot prints provided around the sides of the enclosure (4).

2.The unit can be added to a D9210BC by matching the three plastic mount anchors to the available three hole foot prints below the factory installed D9210B.

3.To secure the unit, use the three #8-3/4 in. screws provided.

3.2.4Door Contact (Onboard) Point, Terminals 9 and 10

Description. The D9210B monitors the sensor loop between the input terminal 10 and the common terminal 9 for normal, shorted, or open conditions. This loop is provided for a door contact. The maximum distance the Door Contact may be remoted from the D9210B is 500 feet. The door contact can be programmed as a perimeter, interior, or 24 hour burglar alarm point.

See the D9210B Program Entry Guide (P/N:32207) for assigning a point to the door controller and the panel Program Entry Guide for the point types.

Point Sensor Loop. Install a 1 kΩ resistor at the door contact, not at the terminal of the input.

 

Voltage (VDC)

 

Description

 

 

0 - 1.2

 

Loop shorted

 

1.8Coming from a shorted condition, the D9210B restores the Door Point at 1.8 VDC

2.65Normal loop voltage

4.0 - 5.0

Loop open

3.5Coming from an open condition, the D9210B restores the Door Point at 3.5 VDC

Table 5: Point Tolerance Voltages

This will provide supervision against grounds on the loop. You can connect only one contact, that being the door, to this input.

Point Tolerances. Table 5 shows the voltages that determine the condition of the on-board point. Use the point common as your (-) reference when measuring the point (+). Set your meter for 10 to 24 VDC range.

D9210B Operation and Installation Guide

32206G

Page 16

© 2002 Bosch Security Systems

Page 15 Page 17
Page 16
Image 16
Bosch Appliances D9210B manual Voltage VDC Description Loop shorted, Point Tolerance Voltages
Page 15 Page 17

D9210B specifications

The Bosch Appliances D9210B is a remarkable addition to any modern kitchen, reflecting the brand's long-standing commitment to quality, innovation, and performance. This appliance, often revered for its versatility and user-friendly design, embodies the essence of Bosch's engineering excellence.

One of the standout features of the D9210B is its sleek and sophisticated design. With a streamlined appearance, it can seamlessly integrate into various kitchen styles, from contemporary to traditional. The stainless steel finish not only adds a touch of elegance but also ensures durability and ease of maintenance.

The D9210B is equipped with advanced cooking technologies that cater to both novice cooks and seasoned chefs. It boasts a powerful convection heating system, ensuring even heat distribution for perfectly cooked meals. This technology enables faster cooking times and promotes energy efficiency, making it an environmentally friendly choice. Users can enjoy the advantages of precision cooking, allowing for a wider range of culinary techniques and styles.

Another essential feature of the Bosch D9210B is its intuitive control system. The easy-to-use digital display allows users to select and adjust settings with precision. The sensor technology automatically adjusts cooking times and temperatures, ensuring optimal results with minimal effort.

Safety is also a top priority with the D9210B. It is designed with several safety mechanisms, including automatic shut-off and a safety lock to prevent unintended use, making it a reliable appliance for families.

In addition to its functional attributes, the Bosch D9210B places great emphasis on energy efficiency. The appliance is designed to minimize energy consumption without sacrificing performance, contributing to lower utility bills and a reduced carbon footprint.

Maintenance is made easy with the D9210B. The appliance features removable components that are dishwasher safe, allowing for a straightforward cleaning process. Furthermore, Bosch's reputation for reliability ensures that users can count on this appliance for years of trouble-free operation.

Overall, the Bosch Appliances D9210B exemplifies a perfect balance of style, efficiency, and advanced cooking technology, making it an excellent investment for any kitchen. It is a symbol of the brand's dedication to enhancing culinary experiences while maintaining the highest standards of quality and innovation.
Top Page Image Contents