D9210B

D9210B Overview

2.0D9210B Overview

2.1System Description

2.1.1Operational Primer

The D9210B is a fully supervised, addressable SDI bus device that allows access control integration for the D9412 (8 doors) and D7412 (2 doors) panels. Each D9210B can store up to 986 user tokens (300 tokens for D7412), each with a different access level for each door. Authority for access is controlled by the level of the user, the time of day, the state of the door and the armed state of the area to which the D9210B. Each of the authority restrictions can be controlled through automatic and manual functions.

Users can be added to the system either by local programming using the D5200, remote programming using the Remote Account Manager (RAM), or by adding tokens using the Add User function through the control center(s).

The D9210B is not programmed using a local or remote programmer. The D9210B must be connected to the SDI bus to function properly and receive operational programming parameters and user data.

2.1.1.1 Outputs

Dry contact SPDT relay for 12/24 V strikes. The D136 removable relay provides a Normally Closed (NC), Common (Input voltage) and Normally Open (NO) output. When the relay is energized, the outputs switch to an opposite state.

Buzzer Output. The buzzer output activates when the door sequence begins or if the door is left open for an extended period of time. It provides common to the negative side of the buzzer.

+5 VDC reader output. The +5 V DC output is for ID readers that require a lower voltage than the +12 VDC readers. It provides a maximum of 150 mA.

2.1.1.2 Inputs

SDI input and output. SDI A (yellow) receives data from the SDI A of the panel. SDI B (green) returns data to the SDI B of the panel.

12 VDC input. This input is used to power the D9210B and provides a connection for the 12 VDC reader and 12 VDC buzzer.

Supervised zone input for the door contact. The zone input on the D9210B is used for the door contact that is physically mounted on the door to which the strike is connected.

The input can be configured for shorts/opens on faults but is normal only when the 1000 k Ω resistor is in the circuit.

Unsupervised tamper input. The unsupervised tamper input is normal when open. Upon a short, the point number assigned to the supervised zone is reported as a MISSING PT### report.

Unsupervised Request to Enter [RTE] and Request to Exit [REX] inputs. The [RTE] input and [REX] input are normally open inputs sharing the same common terminal. When momentarily shorted (500 ms) by a dry contact, input will initiate the door sequence. Typical applications include a N/O momentary push button or a N/O momentary relay activation from a Door motion detector device.

The [REX] input generates Door Request to Exit and is used to exit the area assigned to the D9210B without having to use an ID. The [RTE] generates Door Request to Enter and is used to enter the area assigned to the D9210B.

Programming REX Shunt Only and RTE Shunt Only allows you to initiate only the shunt and buzz when the [RTE] or [REX] inputs are shorted. This eliminates the need for a strike and would be used in applications where a push bar is used to open the door.

It is advisable to assign a point number to the device used to activate the [RTE] and [REX] inputs (such as an infrared with addressable ZONEX). This ensures that the device is supervised.

Unsupervised reader. The Weigand Reader input is a five wire input that supplies +5 VDC (use the +12 VDC terminal for 12-volt readers), negative, ground activation for the reader LED, [D1] and [D0] inputs for the card data.

Two LEDs are provided to indicate that data is reaching the inputs from the reader when an ID is read. The IDs do not have to be valid to illuminate these LEDs, but the IDs do need to have a format that the reader can decipher.

Normal Door Sequence. The Normal Door Sequence of the D9210B is initiated by a valid access granted (User ID) or door request [RTE/REX]. This initiates the strike, shunt and buzz time to activate the strike, shunt the point and create an event reporting the door sequence has begun.

D9210B Operation and Installation Guide

© 2002 Bosch Security Systems

Page 7

32206G

Page 6 Page 8
Page 7
Image 7
Bosch Appliances manual D9210B Overview, System Description, Operational Primer, Outputs, Inputs
Page 6 Page 8

D9210B specifications

The Bosch Appliances D9210B is a remarkable addition to any modern kitchen, reflecting the brand's long-standing commitment to quality, innovation, and performance. This appliance, often revered for its versatility and user-friendly design, embodies the essence of Bosch's engineering excellence.

One of the standout features of the D9210B is its sleek and sophisticated design. With a streamlined appearance, it can seamlessly integrate into various kitchen styles, from contemporary to traditional. The stainless steel finish not only adds a touch of elegance but also ensures durability and ease of maintenance.

The D9210B is equipped with advanced cooking technologies that cater to both novice cooks and seasoned chefs. It boasts a powerful convection heating system, ensuring even heat distribution for perfectly cooked meals. This technology enables faster cooking times and promotes energy efficiency, making it an environmentally friendly choice. Users can enjoy the advantages of precision cooking, allowing for a wider range of culinary techniques and styles.

Another essential feature of the Bosch D9210B is its intuitive control system. The easy-to-use digital display allows users to select and adjust settings with precision. The sensor technology automatically adjusts cooking times and temperatures, ensuring optimal results with minimal effort.

Safety is also a top priority with the D9210B. It is designed with several safety mechanisms, including automatic shut-off and a safety lock to prevent unintended use, making it a reliable appliance for families.

In addition to its functional attributes, the Bosch D9210B places great emphasis on energy efficiency. The appliance is designed to minimize energy consumption without sacrificing performance, contributing to lower utility bills and a reduced carbon footprint.

Maintenance is made easy with the D9210B. The appliance features removable components that are dishwasher safe, allowing for a straightforward cleaning process. Furthermore, Bosch's reputation for reliability ensures that users can count on this appliance for years of trouble-free operation.

Overall, the Bosch Appliances D9210B exemplifies a perfect balance of style, efficiency, and advanced cooking technology, making it an excellent investment for any kitchen. It is a symbol of the brand's dedication to enhancing culinary experiences while maintaining the highest standards of quality and innovation.
Top Page Image Contents