Measure Wire for Remote Mounting | Bradford-White Corp 47808A

Remote Mounting the Setback Control

Measure Wire for Remote Mounting

Step 5: Measure and cut (3) pieces of 18 AWG wire to a sufficient length to reach from the backplate on the Setback Control Junction Box Assembly to the Setback Control Protective Plate. This is shown in Figure 11.

18 AWG

Wire

Figure 11

Label the Wires for Remote Mounting

Step 6: Label the (3) cut wires (A), (B), and (C) respectively. Label both ends of the wires. This is shown in Figure 12. Masking tape can be used to label the wires.

Figure 12

Label Each

Wire

-11-

Image 11

Bradford-White Corp 47808A, 238-47808-00A Measure Wire for Remote Mounting, Label the Wires for Remote Mounting

Contents

Setback Control With Troubleshooting Guide Water Heater Setback Control Important Information Read Carefully Important Information Table of Contents Inspection of Setback Control Installing the Setback ControlUnplug the Water Heater and Setback Control Removal of Setback Control Protective Plate Install Batteries Powering the Water Heater and Setback Control Installing Setback Control Remove the Setback Control from the Backplate Remote Mounting the Setback Control Mount the Protective Plate Prepare the Backplate for Wiring Label the Wires for Remote Mounting Measure Wire for Remote Mounting Install Wire a Backplate Prepare the Wires for Installation Install Wire B Backplate Fasten Wire a into its Designated Location Backplate Install Wire C Backplate Fasten Wire B into its Designated Location Backplate Route Wires to Protective Plate Fasten Wire C into its Designated Location Backplate Fasten Wire a into its Designated Location Protective Plate Install Wire a Protective Plate Fasten Wire B into its Designated Location Protective Plate Install Wire B Protective Plate Fasten Wire C into its Designated Location Protective Plate Install Wire C Protective Plate Install Cover Plate Install Setback Control Powering the Water Heater and Setback Control Changing the Batteries Removal of Setback Control Junction Box Assembly Cover Re-installation of Battery Holder Removal of Battery HolderReplacement of Batteries Powering the Water Heater and Setback Control Right Button Overview of Control Display and Buttons Display Key Display Key and Features Wake Reference Time / Water Temperature Table Select the Correct Hour Start-up ProcedureScreen When Power is Applied Revision Level Screen Lock in the Correct Minute Locking in the Correct HourSelect the Correct Minute Select the Day Select AM / PMLock in AM / PM Finishing the Start-up Procedure Setting the Schedule Setting the Setback Control Schedule Initial Set-up Lock in Wake Period Start Time Select the Leave Period Start Time Select the Wake Period Water TemperatureLock in Wake Period Water Temperature Lock in Leave Period Start Time Select the Return Period Start Time Select the Leave Period Water TemperatureLock in Leave Period Water Temperature Lock in Return Period Start Time Select the Sleep Period Start Time Select the Return Period Water TemperatureLock the Return Period Water Temperature Lock the Sleep Period Start Time Lock in Sleep Period Water Temperature Select Sleep Period Water Temperature Lock in the Day to Edit Enter Editing the Schedule ModeEditing the Setback Schedule Select the Day to Edit Edit AM / PM Edit the Wake Period Start TimeLock in the Wake Period Start Time Lock in the Wake Period Water Temperature Edit the Wake Period Water Temperature Lock in the Leave Period Start Time Edit the Leave Period Start Time Lock in the Leave Period Water Temperature Edit the Leave Period Water Temperature Lock in the Return Period Start Time Edit the Return Period Start Time Lock in Return Period Water Temperature Edit the Return Period Water Temperature Lock in the Sleep Period Start Time Edit the Sleep Period Start Time Lock in the Sleep Period Water Temperature Edit the Sleep Period Water Temperature Exiting the Edit Schedule Mode Exiting a Temporary Hold Setting a Temporary Temperature HoldSetting a New Water Temperature Display of Temporary Hold Water Temperature Exiting a Permanent Hold Setting a Permanent Temperature HoldDisplay of Permanent Hold Water Temperature Lock in Correct Hour Enter Clock / Day Editing ModeEditing the Clock / Day Select Correct Hour Lock in Correct Minute Select Correct Minute Select Correct Day Lock in Correct Day & Complete Editing Clock / Day Mode Start Editing Friday Sabbath Time Period EditingEnter Sabbath Time Period Editing Edit the Wake Period Start Time Lock in AM / PM AM/PM symbol flashes Edit Leave Period Water Temperature Edit the Return Period Start Time Edit Return Period Water Temperature Lock in Sleep Period Start Time Edit Sleep Period Start Time Lock the Sleep Period Water Temperature Continuing with Sabbath Time Period Editing Description Diagnostic CodesPage Page Sales/866-690-0961 Fax/905-238-0105 Sales/800-523-2931 Fax/215-641-1670 Parts Fax/215-641-2108