Regular Maintenance |
|
|
Parking Brake Adjustment |
|
|
(S/N: 2013521289 & Below) |
|
|
There are two brake springs located by the rear | A | A |
wheels of the unit. If the parking brake springs need | ||
to be adjusted both parking brake springs must be |
|
|
adjusted equally. |
|
|
1. Disengage the PTO, engage the parking brake,
stop the engine and remove the ignition key.
2. Locate the two (2) brake springs (A, Figure 32).
3.With the parking brake engaged, measure the compressed spring length. The spring should
be
4. | If the spring is not within this range, release the |
|
|
| A |
|
| |
| parking brake and turn the adjustment nut (B) to |
|
|
|
|
| ||
|
|
|
|
|
|
| ||
| compress or release the spring. |
|
|
|
|
| B |
|
5. | Engage the parking brake and |
|
|
|
|
| ||
| spring. |
|
|
| (6,67 cm) |
|
|
|
| If this does not correct the braking problem, see |
|
|
|
|
|
| ||
| your Ferris dealer. |
|
|
|
|
|
|
| |
Parking Brake Adjustment |
|
| Figu e 32. | Park ng Brake Adjustment |
|
| ||
|
| A. Brake Spr ng |
|
|
| |||
(S/N: 2013521290 & Above) |
|
|
|
|
| |||
|
| B. Adjus ment Nut |
|
|
| |||
The parking brake system consists of two range | for |
|
|
|
| |||
selector plates and two parking brake springs which |
|
|
|
| ||||
are located by the rear wheels of the unit. If the |
|
|
|
| ||||
| A |
|
|
|
| |||
parking brake needs to be adjusted the range select | r |
|
| 2 3 | 4 | |||
C |
| 1 | ||||||
plates must be adjusted first, and then the length of |
|
|
|
| ||||
| B |
|
|
|
| |||
the parking brake springs must be set. |
|
|
|
|
| |||
| Adjusting the Range Selector Plate Not |
|
|
|
|
|
| ||
1. | Disengage the PTO, engage the parking brake, |
|
|
|
|
|
| |
| stop the engine and remove the ignition k y. |
|
|
|
|
|
| |
2. | Chock the front tires to prevent the machine from |
|
|
|
|
|
| |
| moving. Jack up the rear of the machine and |
|
|
|
|
|
| |
| secure with jackstands. |
|
| D |
|
|
|
|
3. | Remove both of the rear wheels. |
|
|
|
|
|
| |
Reproduction |
|
|
| |||||
4. | Disengage the parking brake. |
|
|
| ||||
|
|
|
|
| ||||
5. | Remove the range selector hardware (A, Figure |
|
|
|
|
|
| |
| 33). |
|
|
|
|
|
|
|
6. | Loosen the range selector pivot hardware (B) just |
| Figure 33. | Adjusting the Range Selector Plate |
| |||
| enough so that you can pivot the range selector |
| A. Range Selector Hardware |
|
|
| ||
| plate (C). |
|
| B. Range Selector Pivot Hardware |
|
|
| |
7. | Pivot the range selector plate towards the front |
| C. Range Selector Plate |
|
|
| ||
|
|
|
|
|
| |||
of the machine as far as you can and insert the | D. Brake Hub |
| |
range selector hardware in the nearest hole. |
|
30 | www.ferrisindustries.com |