Manuals / Brother / Household Appliance / Sewing Machine

Brother Brother CP-6500 operation manual

Models: Brother CP-6500

1 100

Download 100 pages 50.81 Kb

Page 37

——————————————————————————————————————————————————————————————————————————————————————————————————————————————————————

bHold the presser foot holder in place with your right hand, and then tighten the screw using the disc-shaped screwdriver in your left hand.

aDisc-shaped screwdriver

bPresser foot holder

cPresser foot holder screw

Note

●If the presser foot holder is not correctly installed, the thread tension will be incorrect.

CAUTION

●Be sure to securely tighten the presser foot holder screw, otherwise the presser foot holder may fall off and the needle may strike it, causing the needle to bend or break.

1

35

Image 37

Brother Brother CP-6500 operation manual

Contents

Sewing Basics Utility Stitches Page Important Safety Instructions For a longer service life For Users in the UK, EIRE, Malta Cyprus only Contents Utility Stitches Included accessories AccessoriesAbout zigzag foot J Accessory compartment Optional accessoriesMain parts Names of Machine Parts and Their FunctionsOperation buttons Needle and presser foot sectionButtons provided on some models Spool pin Operation panelBPushplace.the spool pin down until it locks into Shown.1Power supply precautions Using Your Sewing MachinePower supply Changing the needle stop position Foot controllerAright to select the desired sewing speed Side of stitch selection keyWinding the bobbin Threading the MachineBRemove the spool cap DSlide the spool cap onto the spool pin KTrim the excess thread above the bobbin Make sure that the thread passes under the pretension diskFor models equipped with the fast bobbin winding system Thread is cut to a suitable length Actual size 11.5mm 7/16 inch This model Lower threadingFor models equipped with the quick-set bobbin Slit Cutter Cut the thread with the cutter Upper threading GSlide the spool cap onto the spool pin Remove the spool capThread take-up lever Needle bar thread guide Catch the thread on the hook as shown below DFully lower the needle threader leverLightly hold the end of the upper thread Drawing up the lower threadBobbin cover should still be removed Replacing the Needle Needle precautionsNeedle types and their uses Replacing the needle Checking the needleCLower the presser foot lever Install the twin needle in the same waySewing with the twin needle Installthread.the thread spool and thread the upperThread the upper thread for the left needle For details, refer to steps a through l of Upper threadingHAttach zigzag foot J For details, refer to step a through l of Upper threadingModels equipped with a needle threader Turn on the sewing machine Select a stitchReplacing the presser foot Replacing the Presser FootReplace the presser foot as described below Mark on the wheel points up. With modelsRemove the presser foot Removing the presser foot holderFor details, refer to Replacing the presser foot Page Follow the basic procedures below to sew General sewing procedureSewing Selecting stitching DIfwidth.necessary, adjust the stitch lengthPress the + or side of to increase or On the left changes the digit on the leftRight of in the LCD Adjusting the stitch length and widthOn the wheel points up. With models equipped Starting to sewBRaise the presser foot lever Sewing reinforcement stitches Raise the presser foot leverEach other Correct tension Thread tensionUpper tension is too tight Upper tension is too looseTrial sewing Useful Sewing TipsChanging the sewing direction Sewing curvesPresser foot remains level, allowing the fabric to be fed Sewing hook-and-loop FastenerSewing stretch fabrics Sewing thin fabricsStitching cylindrical pieces Slide the flat bed attachment to the left to release itOvercasting Stitches Using zigzag footAttach zigzag foot J Select stitch , or CSew with the edge of the fabricAttach overcasting foot G Select stitch or Using overcasting footBasic Stitching When sewing is finished, cut the threadBasic stitching For details, refer to Starting to sewReverse the skirt or pants Blind HEM StitchingFold back the fabric inside along the basting Thick fabric Normal fabric Stitch widthIf the needle does not catch the hem fold Buttonholes can be sewn and buttons can be sewn on Buttonhole SewingAuto Rfc. Automatic Reinforcement **Rfc. Reinforcement Size of the buttonhole is set Raiseposition.the buttonhole lever to its original Once sewing is completed,Trim off any excess of the gimp thread Sewing buttonholes on stretch fabricsDPlacethe fabric.a button between the presser foot Button sewingESelect a stitch With stitch Select stitchNormally, the feed dog position lever is Positioned at After sewing for about 10 seconds at lowRev. Reverse Do not use reverse stitching Zipper InsertionRefer to Basic stitching on Sew the stitching in order, from a to c FSelect stitchStretch stitching Sewing Stretch Fabrics and Elastic TapeElastic attaching BAttach zigzag foot J CSelect stitchUtility Stitches Piecing APPLIQUÉ, Patchwork and Quilt StitchingPatchwork crazy quilt stitching AppliquésPiecing Remove the basting, if necessaryFor a seam allowance on the left side QuiltingDSelect stitch SewingFree-motion quilting Using the optional quilting guide† Walking foot † Presser foot holder ARemoveholder. the presser foot and the presser footNormally, the feed dog position lever is Positioned at Slide the feed dog position lever, located atTriple stretch stitching Reinforcement StitchingBar tack stitching Attach zigzag foot J Select stitch Start sewingPullpossible.down the buttonhole lever as far as Once sewing is completed,Select a stitch width of 5.0 mm 3/16 inch or less Decorative StitchingFor details, refer to Selecting stitching FagotingSmocking Scallop stitchingDTrim along the stitches CSew parallel stitching at intervals of 10 mm 3/8 inchJoining Shell tuck stitchingFold the fabric along the bias BAttach zigzag foot J Unfold the fabric, and then iron the tucks down to one sideHeirloom stitching Utility stitches Stitch SettingsPattern No Decorative Stitch Buttonhole Bar tack For decoration, etc For decoration, etc Yes Cleaning the machine surface MaintenanceCleaning the bobbin case Remove the bobbin caseAlign the U and marks Needle plate cover Frequent troubleshooting topics TroubleshootingUpper thread tightened up For details, refer to Cleaning the bobbin case on SymptomTangled thread on wrong side of fabric Cause Incorrect upper threadingHFeed the upper thread as shown in the illustration below Thread take-up lever Incorrect thread tension DRemoveholder. the presser foot and presser foot Fabric is caught in the machine and cannot be removedIf threads remain in the bobbin case, remove them Be careful not to drop the removed screws in the machine Be careful not to drop the removed screws in the machineMemo Checking machine operations Do not yet install the presser foot and threadTurn on the machine Select middle needle position stitch Correctly thread the machineList of symptoms Machine does While sewingNot work Fabric being Sewn withThread breaks UpperLower Or breaksSkipped Stitches areThere is a high Pitched noise While sewingThread has After sewingTightened up ThreadOperation beep for models equipped with the operation beep Error MessagesNumerics Index42 , 45 English 885-V60/V61/V62/V63/V64/V65 XE6528-2012