Manuals / Brands / Household Appliance / Sewing Machine / Brother / Household Appliance / Sewing Machine

Brother 884-B01, OVERLOCK MACHINE Needle, Removing/Installing the needle, Needle description, How to check the needle

1 80

Download 80 pages, 4.23 Mb

Needle

This machine uses a standard home sewing machine needle.

The recommended needle is SCHMETZ 130/705H (#80 or #90).

Needle description

1 Back (flat side) 2 Front 3 Groove

1 2

3

How to check the needle

4Flat surface

5Place the needle on its flat side and check to see if the space is parallel.

5

4

NOTE:

Countermeasures for material breakage <A>.

It can reduce the occurrence of material breakage by using SCHIMETZ 130/705H SUK (#90) BALL POINT.

Removing/Installing the needle

<A> Removing/ installing the left needle <B> Removing/ installing the right needle

<A>	<B>
1	1
2	2

1 Tighten

2 Loosen

	To remove:
	1.	Turn the main power and light switch to the
		OFF position.
	2.	Turn the hand wheel so that the mark on the
	2.	Turn the hand wheel so that the mark on the
		hand wheel is aligned to the line on the
		machine. (See CHAPTER 1 "Turning direction	English
		of hand wheel".)
	3.	Loosen the corresponding needle set screw
	3.	Loosen the corresponding needle set screw
		with turning the included hexagonal driver
		toward 2 in the figure, and remove the needle.

To install:

1.Turn the main power and light switch to the OFF position.

2.Turn the hand wheel so that the line on the hand wheel is aligned to the line on the machine.

3.Hold the needle with its flat side away from you and insert it up as far as it will go.

4.Tighten the needle set screw securely with turning the included hexagonal driver toward 1 in the figure.

NOTE:

Make sure to insert the needles to the highest point in the needle chamber.

If the needles have been inserted correctly, the right needle should be set slightly lower than the left one.

CAUTION

Always be sure to turn off the power before removing/ inserting the needle.

Do not drop the needle and needle set screw in the machine, otherwise it may be damaged.

11

Contents

http://solutions.brother.com Page IMPORTANT CONGRATULATIONS ON CHOOSING THIS COMPACT OVERLOCK MACHINE Notes on the motor WARNING LABELS Page Page Accessories Included accessory Optional accessory Powering the machine Turning on the machine Operation Turning direction of hand wheel Opening/ Closing front cover Trim trap Wide table Retracting knife Stitch length Stitch width Differential feed Differential feed adjustment Adjusting the presser foot pressure Tension adjustment dial Tension control Chart of thread tension adjustment, Two-needle (Four-thread) Chart of thread tension adjustment, One-needle (Three-thread) Chart of thread tension adjustment, One-needle (Two-thread) Needle Needle description How to check the needle Removing/Installing the needle Thread tree How to use the thread spool cap How to use the thread net Before threading Thread for two-needle four-thread Thread for one-needle three-thread overlock stitch (left needle) Thread for one-needle two-thread overlock stitch (right needle) Threading the lower looper Lower looper easy threading operation Threading the upper looper Threading the left needle Threading the right needle Threading the needle (using the needle threader) SEWING MATERIALS,THREADS AND NEEDLES COMPARISON CHART Stitchselection Four-threadoverlock stitch Three-threadoverlock stitch 5 mm (3/16 inch) Three-threadoverlock stitch 2.8 mm (7/64 inch) Two-threadoverlock stitch 5 mm (3/16 inch) Chaining-off Tostartsewing Toremovework Tosecurechain Method Ifthreadsbreakduringsewing Tosewfinematerials To use the stitch finger W Two-threadsewing How to set the thread change assembly Chart of two-threadoverlock stitch Narrowoverlock/Rolledhemmingstitch Instructions for both narrow overlock/ Rolled hemming stitches Chart of narrow overlock/ Rolled hemming stitch Page Cleaning Oiling Blind stitch foot Features Blind stitching Flatlock stitching Pin tuck stitching Taping foot Machine setting (type of stitch): How to set the elastic / tape Test sewing Pearl sequence foot Preparation How to adjust the machine How to set fabric and pearl Pipingfoot How to set fabric and piping tape Start sewing Gatheringfoot How to set fabric Specifications Use Sewing speed Stitch width Stitch length (pitch) Page IMPORTANTE ENHORABUENA POR HABER ELEGIDO ESTA COMPACTA MAQUINA OVERLOCK Notas sobre el motor Dentro de la tapa trasera Page Accesorios Accesorios incluidos Accesorios opcionales Encendido de la máquina Activación de la máquina Funcionamiento Cambio de la dirección de la ruedecilla Apertura/cierre de la tapa delantera Orificio de corte Costura de mangas (extracción del suplemento para la mesa) Mesa ancha Repliegue de la cuchilla Largo de las puntadas Ancho de las puntadas Alimentador con diferencial Ajuste del alimentador con diferencial Ajuste de la presión del prensatelas Disco de ajuste de la tensión Control de la tensión Tabla de ajuste de tensión de los hilos, dos agujas (cuatro hilos) Tabla de ajuste de tensión de los hilos, una aguja (tres hilos) Tabla de ajuste de tensión de los hilos, una aguja (dos hilos) Aguja Descripción de la aguja Cómo comprobar la aguja Desmontaje/instalación de la aguja Árbol del hilo Como utilizar el tope del carrete Cómo utilizar la malla para hilo Antes de enhebrar Enhebrado para puntadas Overlock de dos agujas y cuatro hilos Enhebrado para puntadas Overlock de una aguja y tres hilos (aguja izquierda) una aguja y dos hilos (aguja derecha) Enhebrado del áncora inferior Proceso simple de enhebrado del áncora inferior Enhebrado del áncora superior Enhebrado de la aguja izquierda Enhebrado de la aguja derecha Enhebrado de la aguja (utilizando el enhebrador de aguja) Page Selección de las distintas puntadas Puntada overlock de cuatro hilos Puntada overlock de tres hilos 5 mm Puntada overlock de tres hilos 2,8 mm Costura de prueba Cadeneta Para empezar a coser Para retirar el trabajo Para asegurar la cadeneta Método Si los hilos se rompen al coser Para coser tejidos finos Para utilizar la uñeta de puntadas W Puntada de dos hilos Cómo ajustar el conjunto de cambio de hilo Tabla de puntada Overlock de dos hilos Puntada overlock estrecha/de dobladillo enrollado Tabla de puntada overlock estrecha/de dobladillo enrollado Page Limpieza Engrasado Prensatelas para puntadas invisibles Características Puntadas invisibles Puntadas overlock planas Puntadas de pliegues pequeños Prensatelas para cintas Ajuste de la máquina (tipo de puntada): Como ajustar la cinta o el elástico Costura de prueba Prensatelas para tira de perlas Preparación Cómo ajustar la máquina Cómo ajustar el tejido y las perlas Prensatelas para ribeteados Cómo ajustar el tejido y la cinta de ribetear Empiece a coser Prensatelas fruncidor Cómo ajustar el tejido Especificaciones Uso Velocidad de costura Ancho de las puntadas Largo de las puntadas (altura)