SP1.7 Specifications, Inputs | Bryston specs

SP1.7 SPECIFICATIONS

Inputs
Analog Audio:	Six stereo (RCA) pairs, One 5.1 channel (RCA) input
Digital:	4 coaxial (RCA) 75 Ohms, 2 Optical (TOSLINK?), conforms to S/PDIF standard.
	Pro version 1 AES/EBU input (XLR) 110 Ohms
Infrared:	1 mini phone jack
RS-232:	D9 connector (bidirectional)
Outputs
Analog Outputs:	Left, Centre, Right, Right Surround, Left Surround, and Subwoofer on 6 unbalanced
	(RCA) and 6 balanced (XLR).
	2 stereo (RCA) pairs of Record Outputs.
	1 pair (RCA) Surround Back outputs
Trigger:	One 12V on/off trigger, One 12V programmable trigger, to source 80mA total.

Remote

30 button, Hand-Held, Infrared remote control unit operates with two AAA batteries (included).

Performance Specifications
A/D Conversion:	24-Bit, 48kHz Delta-Sigma
D/A Conversion:	24-Bit, 96kHz Delta-Sigma
DSP Engine:	Motorola 56367
Power Supply:	Dual, Linear, Toroidal
Frequency Response:	20Hz to 20kHz +/- 0.25 dB
THD+Noise:	Less than 0.006% in DSP modes; Less than 0.0025% in Bypass mode 20Hz to
	20kHz at maximum output level.
Signal-to-Noise Ratio:	105dB in DSP Modes; 110dB in 2ch Bypass Mode ; 22kHz bandwidth, Ref. 1kHz at
	maximum output level
Input Level:	2 Vrms in DSP modes; 4 Vrms in Bypass Mode
Input Impedance:	50kOhms
Output Level:	8 Vrms (16 Vrms Balanced) in DSP Modes; 10 Vrms (20 Vrms Balanced) in Bypass Mode.
Output Impedance:	110 Ohms
Bass Management:	2nd Order HPF(x5), 4th Order LPF; 60 – 220 Hz Crossover Freq.
Physical Specifications
Power Requirements	100VAC, 115VAC, and 230VAC models. 200 VA. IEC detachable power cord (included)
Dimensions:	17” W x 13.5” D x 3.8” H; rackmount 19” W x 13.5” D x 3.5” H
Weight:	approx 22 lbs (10 kg)
Chassis Temp:	0 to 50 deg Celsius

Specifications subject to change without notice.

36

Image 38

Bryston manual SP1.7 Specifications, Inputs

Contents

SP1.7 Bryston 20-YEARWARRANTY 800 632 Contents Accessories SP1.7 Functional Layout Power Power Input Mode Standby and IR Infrared Activity Indicator Front Panel Controls and IndicatorsPower Momentary Switch Using the Dynamic Range Control LCD Display window Source Selection Buttons and Indicators Menu Control Buttons Surround Button Mode Selection ButtonsDigital Mode and Indicator Stereo and Stereo Downmix Mode Mono and Mono Downmix Modes THX Button Mode Button Available with THX Listening Mode… Analog Balance Master VolumeBypass Button Analog Inputs Rear Panel Input and Output ConnectionsBalanced and 2. Unbalanced Outputs Digital Audio Coaxial Inputs Tape/Recording Outputs Setting the Optical Audio Input AssignmentToslink Digital Audio Optical Inputs Programming the AUX Trigger Output RS-232 connectorRemote 12V Trigger Outputs Aux IR Receiver Master Power Switch SP1.7 Remote ControlIEC Power Connector Fuses Source Select Buttons Power Button Mode Select ButtonsVolume/Trim Buttons Setup Buttons Status LED Photo Sensor SET UP and Calibration of the SP1.7 To accomplish this process the following tools are needed Explanation of ‘Saved Settings per Source’ Feature Setting the Speaker Configuration Explanation of ‘Xtra Bass’ Mode Setting the Speaker Crossover Frequency Highlight SP Setup Menu Setting the Channel Delays Change the Crossover Frequency Calibrating and Setting Levels/Channel to Channel Balance Setting Channel Levels without Pink Noise Setting the Bplm with Pink Noise Setting the THX Subwoofer Limiter or Bass Peak Level Manager Setting the Bplm without Pink Noise Enabling DTS-ES 6.1 Decoding Hightlight ES Other Settings Menu Enabling THX Surround EX Decoding Changing Dolby Plii Music Settings Change EX Control Setting Highlight Plii Setup Menu Changing DTS NEO6 Settings Center Image is a variable in Neo6 music mode only To change the Center Image Acknowledgements Appendix a SP1.7 Surround Modes Surround ModesPage Signal Table of all available surround modes Appendix B THX Information DTS as per THX licensing agreements Example HOOK-UP Diagrams XLR/PHONE SP1.7 Specifications Inputs Suggested Surround Speaker Placement