Manuals / Cabletron Systems / Computer Equipment / Switch

Cabletron Systems 2H253-25R manual Tabletop or Shelf Installation

Models: 2H253-25R

1 64

Download 64 pages 45.77 Kb

Page 33

3.3.1Tabletop or Shelf Installation

Installing the Device

3.3.1Tabletop or Shelf Installation

The following two subsections provide guidelines for installation on a tabletop or shelf.

Guidelines for Tabletop and Shelf Installations

Tabletop and shelf installations must be within reach of the network cabling and meet the requirements listed below:

•Locate the 2H253-25R within seven feet of an appropriately grounded power receptacle that meets the power supply requirements listed in Appendix A.

•In a shelf installation, the shelf must support 13.5 kg (30 lb) of static weight for each 2H253-25R.

•Maintain a temperature of between 5°C (41°F) and 40°C (104°F) at the installation site with ﬂuctuations of less than 10°C (18°F) per hour.

To ensure proper ventilation and prevent overheating, leave a minimum clearance space

!of 5.1 cm (2.0 in) at the left, right, and rear of the 2H253-25R.

CAUTION

•Maintain a 2-inch clearance from the left, right, and rear sides of the device to provide adequate ventilation.

Installation

For a tabletop or shelf installation, locate the 2H253-25R within seven feet of its power source and on an unrestricted free surface area as shown in Figure 3-1. Proceed to Section 3.3.3 for power connection instructions.

Installation 3-3

Image 33

Cabletron Systems 2H253-25R manual Tabletop or Shelf Installation, Guidelines for Tabletop and Shelf Installations

Contents

FAST ETHERNET WORKGROUP SWITCH 2H253-25R SmartSwitch Installation User’s GuideRESET 2H253-25RPage Only qualiﬁed personnel should perform installation procedures FCC NOTICE INDUSTRY CANADA NOTICEVCCI NOTICE CABLETRON SYSTEMS, INC PROGRAM LICENSE AGREEMENT Page CABLETRON SYSTEMS SALES AND SERVICE, INC PROGRAM LICENSE AGREEMENT 7. NO LIABILITY FOR CONSEQUENTIAL DAMAGES. IN NO EVENT SHALL CABLETRON OR ITS SUPPLIERS BE LIABLE FOR ANY DAMAGES WHATSOEVER INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS, PROFITS, BUSINESS INTERRUPTION, LOSS OF BUSINESS INFORMATION, SPECIAL, INCIDENTAL, CONSEQUENTIAL, OR RELIANCE DAMAGES, OR OTHER LOSS ARISING OUT OF THE USE OR INABILITY TO USE THIS CABLETRON PRODUCT, EVEN IF CABLETRON HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. BECAUSE SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, OR IN THE DURATION OR LIMITATION OF IMPLIED WARRANTIES IN SOME INSTANCES, THE ABOVE LIMITATION AND EXCLUSIONS MAY NOT APPLY TO YOU CABLETRON SYSTEMS LIMITED PROGRAM LICENSE AGREEMENT viii If the Program is exported from the United States pursuant to the License Exception TSR under the U.S. Export Administration Regulations, in addition to the restriction on transfer set forth in Sections 1 or 2 of this Agreement, You agree not to i reexport or release the Program, the source code for the Program or technology to a national of a country in Country Groups D1 or E2 Albania, Armenia, Azerbaijan, Belarus, Bulgaria, Cambodia, Cuba, Estonia, Georgia, Iraq, Kazakhstan, Kyrgyzstan, Laos, Latvia, Libya, Lithuania, Moldova, North Korea, the People’s Republic of China, Romania, Russia, Rwanda, Tajikistan, Turkmenistan, Ukraine, Uzbekistan, Vietnam, or such other countries as may be designated by the United States Government, ii export to Country Groups D1 or E2 as deﬁned herein the direct product of the Program or the technology, if such foreign produced direct product is subject to national security controls as identiﬁed on the U.S. Commerce Control List, or iii if the direct product of the technology is a complete plant o r any major component of a plant, export to Country Groups D1 or E2 the direct product of the plant or a major component thereof, if such foreign produced direct product is subject to national security controls as identiﬁed on the U.S. Commerce Control List or is subject to State Department controls under the U.S. Munitions ListDECLARATION OF CONFORMITY Page INTRODUCTION ContentsNETWORK REQUIREMENTS ABOUT THIS GUIDETROUBLESHOOTING INSTALLATIONSPECIFICATIONS OPTIONAL INSTALLATIONS AND MODE SWITCH BANK SETTINGSxiii FiguresTroubleshooting Checklist TablesLANVIEW LEDs COM Port Pin AssignmentsAbout This Guide USING THIS GUIDESTRUCTURE OF THIS GUIDE Important NoticeRELATED DOCUMENTS HSIM-W6 Installation Guide HSIM-W84 Installation GuideEthernet Technology Guide Cabling Guide SmartTrunk User’s Guide WAN Series Local Management User’s GuideThe guide uses the following conventions DOCUMENT CONVENTIONSPage Introduction 1.1 OVERVIEWImportant Notice 1.1.2 Auto-Negotiation 1.1.1 Connectivity1.1.3 Runtime IP Address Discovery 1.1.4 Full Duplex Switched Ethernet1.1.5 SmartTrunk The 2H253-25R will reboot after RAD is successful1.1.6 Remote Monitoring RMON 1.1.7 Broadcast Suppression1.1.8 Port/VLAN Redirect Functions 1.1.10 Flow Control 1.1.9 Rate Limiting1.1.14 Switching Options 1.1.11 GARP Switch Operation1.1.12 802.1 Port Priority 1.1.13 Management1.1.15 Optional HSIMs and VHSIMs 1.1.18 LANVIEW Diagnostic LEDs1.1.16 Standards Compatibility 1.1.17 Year 2000 Compliant1.2 GETTING HELP anonymousyour email address Network Requirements 2.1 SmartTrunk2.2 10BASE-T NETWORK 2.3 100BASE-TX NETWORK 100BASE-TX Network2-2 Network Requirements 3.1 UNPACKING THE DEVICE Installation3.2 INSTALLING OPTIONS 3.3 INSTALLING THE DEVICETable 3-1 Contents of 2H253-25R Carton 3.3.1 Tabletop or Shelf Installation Guidelines for Tabletop and Shelf InstallationsInstallation 3.3.2 Rackmount Installation Guidelines for the Rackmount InstallationA = 15 cm 6 in B = 57 cm 22.5 in C = 53 cm 21 in D = 213 cm 7 ft Attaching the Strain-Relief Bracket InstallationRack mounting the 2H253-25R involves the following Rack Mounting the 2H253-25R To connect the 2H253-25R to the power sources, proceed as follows 3.3.3 Connecting Power3.4 CONNECTING TO THE NETWORK Transmit TX Figure 3-6 Straight Cable Connection3.5 COMPLETING THE INSTALLATION 4.1 USING LANVIEW TroubleshootingDevice electronics not Table 4-1 LANVIEW LEDs Cont’d Should ﬂash green every two Refer to the SmartSwitch Series 4.2 TROUBLESHOOTING CHECKLIST1. Refer to the SmartSwitch Series 2E253, 2H252, 2H253, and 2H2582H258 Local Management User’s Series 2E253, 2H252, 2H253, andRefer to the SmartSwitch Series 2E253, 2H252, 2H253, and 2H258sometime before either cycling NVRAM Reset, was changedFigure 4-2 RESET Button 4.3 USING THE RESET BUTTONA.1 DEVICE SPECIFICATIONS SpeciﬁcationsA.2 PHYSICAL PROPERTIES A.4 ENVIRONMENTAL REQUIREMENTS A.3 ELECTRICAL SPECIFICATIONSA.5 INPUT/OUTPUT PORTS 200-240 VacA.6 COM PORT PINOUT ASSIGNMENTS A.7 REGULATORY COMPLIANCEFCC Part 15, CSA C108.8, 89/336/EEC, EN Page B.1 REQUIRED TOOLS Optional Installations and Mode Switch Bank SettingsThis section describes how to remove the 2H253-25R chassis cover B.2 REMOVING THE CHASSIS COVERB-2 Optional Installations and Mode Switch Bank Settings Removing the Chassis CoverTo remove the chassis cover, proceed as follows Removing the Chassis Cover B-4 Optional Installations and Mode Switch Bank SettingsScrews Chassis Cover Front Panel Chassis Figure B-1 Removing the Chassis CoverB.3 SETTING THE MODE SWITCHES B.4 SIMM UPGRADE SIMM UpgradeB-6 Optional Installations and Mode Switch Bank Settings B.4.1 Locating SIMMs B.4.2 Installing the DRAM SIMMConnector Connector Teeth Clip Side Notch SIMM UpgradeFigure B-4 Installing the DRAM B-8 Optional Installations and Mode Switch Bank SettingsInstalling Optional HSIM or VHSIM Interface Modules B.5 INSTALLING OPTIONAL HSIM OR VHSIM INTERFACE MODULESFigure B-5 HSIM and VHSIM Connector Locations Optional Installations and Mode Switch Bank SettingsPage Numerics IndexIndex-2 Index