Canon 650D, 6558B001, 6558B003, 6558B005, EOS 650 Notes on Movie Shooting

kShooting Movies

Notes on Movie Shooting

During movie shooting, do not point the lens toward the sun. The sun’s heat can damage the camera’s internal components.

If <Q> is set and the ISO speed or aperture changes during movie shooting, the white balance may also change.

If you shoot a movie under fluorescent or LED lighting, the movie may flicker.

Zooming the lens during movie shooting is not recommended. Zooming the lens can cause changes in the exposure regardless of whether the lens’ maximum aperture changes or not. Exposure changes may be recorded as a result (except EF-S18-135mm f/3.5-5.6 IS STM).

You cannot magnify the image during movie shooting.

Cautions for movie shooting are on pages 195 and 196.

If necessary, also read the Live View shooting cautions on pages 165 and 166.

Movie-related settings are under the [Z1] and [Z2] tabs (p.191). A movie file is recorded each time you shoot a movie. If the file size exceeds 4 GB, a new file will be automatically created.

The movie image’s field of view is approx. 100% (with movie recording size set to [A]).

The sound will be recorded in stereo by the camera’s built-in microphone (p.170).

Most commercially-available external stereo microphones with a 3.5 mm diameter miniplug can be connected to the camera. If an external microphone has been connected to the camera’s external microphone IN terminal (p.20), it will be given priority over the built-in microphone.

You can use Remote Controller RC-6 (sold separately, p.303) to start and stop the movie shooting if the drive mode is <Q>. Set the shooting timing switch to <2> (2-sec. delay), then press the transmit button. If the switch is set to <o> (immediate shooting), still photo shooting will take effect.

With a fully-charged Battery Pack LP-E8, the total movie shooting time will be as follows: approx. 1 hr. 40 min. at room temperature (23°C/73°F), and approx. 1 hr. 20 min. at low temperature (0°C/32°F).

176

Contents

MANUAL INSTRUCTION Introduction Testing the Camera Before Use and Liability Copyrights Cards that can record movies Item Check List Software Instruction Manuals Conventions Used in this Manual Icons in this Manual Basic Assumptions Chapters Introduction Getting Started Basic Shooting and Image Playback Creative Shooting Contents at a Glance Shooting Shoot automatically p.57 Shoot continuously Focusing Playback Printing Index to Features Power Card Lens Basic Settings Exposure Adjustment Flash Live View Shooting Movie Shooting Playback Contents Introduction 1 Getting Started Basic Shooting and Image Playback Creative Shooting 4 Advanced Shooting 5Shooting with the LCD Monitor (Live View Shooting) Shooting Movies Handy Features Wireless Flash Photography Image Playback Post-ProcessingImages Printing Images Customizing the Camera Reference Handling Precautions Camera Care Cards Cautions regarding Prolonged Use About smudges adhering to the front of the sensor Quick Start Guide Insert the battery (p.30) Insert a card (p.31) Redindex Attach the lens (p.39) Set the lens focus mode switch to <AF> (p.39) Flip out the LCD monitor (p.33) Focus the subject (p.43) Take the picture (p.43) Review the picture (p.200) Nomenclature Page Shooting Settings Viewfinder Information Mode Dial Creative Zone Basic Zone A : Scene Intelligent Auto (p.58) Flash Off Lens without a distance scale Lens with a distance scale Battery Charger LC-E8 Battery Charger LC-E8E Attaching the Strap Charging the Battery LC-E8 LC-E8E 1Remove the protective cover 2 Attach the battery Tips for Using the Battery and Charger Upon purchase, the battery is not fully charged Recharge the battery on the day before or on the day it is to be used When not using the camera, remove the battery Installing and Removing the Battery Installing the Battery Open the cover Insert the battery Removing the Battery Installing and Removing the Card Installing the Card 1 Open the cover Insert the card Removing the Card Make sure the access lamp is off, then open the cover Recording 2 Remove the card Using the LCD Monitor 1 Flip out the LCD monitor Rotate the LCD monitor 3 Face it toward you Turning on the Power About the Automatic Self-CleaningSensor 3About Auto Power Off 52: Auto power off zChecking the Battery Level Battery Life 3Setting the Date, Time, and Time Zone Set the Time Zone London Time zone 3Set the date and time 4Set the daylight saving time 5 Exit the setting 3Selecting the Interface Language 1Display the menu screen 2Under the [52] tab, select [LanguageK] LanguageK Set the desired language Attaching and Detaching a Lens Attaching a Lens Remove the caps Attach the lens 3 Set the lens focus mode switch to <AF About Zooming Detaching the Lens While pressing the lens release button, turn the lens as shown by the arrow About the Lens Image Stabilizer Set the IS switch to <1 Press the shutter button halfway Take the picture Basic Operation Adjusting the Viewfinder Clarity Turn the dioptric adjustment knob Holding the Camera Shutter Button Pressing halfway Pressing completely Preventing Camera Shake QQuick Control for Shooting Functions Basic Zone modes Press the <Q> button Set the desired function Creative Zone modes Sample Quick Control Screen Function Setting Screen 3Menu Operations Menu Screen Movie shooting Menu Setting Procedure 2Select a tab Select the desired item Select the setting Set the desired setting 3Formatting the Card Select [Format card] Format card Format the card Low level format Execute [Format card] in the following cases: The card is new A card-relatederror is displayed (p.331) About Low-levelFormatting Switching the LCD Monitor Display Shooting Settings Menu Functions Captured Image Page Feature Guide Shooting mode (Sample) Quick Control (Sample) 3Disabling the Feature Guide Select [Feature guide] dTouch Screen Operations Tap Quick Control (Sample display) Drag Menu screen (Sample display) Scale display (Sample display) 3Silencing the Beep during Touch Operations 1: Beep 3Touch Control Settings Select [Touch control] Touch control Set the Touch control Cautions for Touch Screen Operations Page About the Auto Lighting Optimizer AFully Automatic Shooting (Scene Intelligent Auto) 4 Take the picture FAQ The focus confirmation light <o> blinks and focus is not achieved Multiple AF points flash simultaneously Page AFull Auto Techniques (Scene Intelligent Auto) ALive View Shooting 1 Display the Live View image on the LCD monitor 2 Focus the subject 7Disabling Flash Shooting Tips Prevent camera shake if the numeric display in the viewfinder blinks Take portraits without flash CCreative Auto Shooting Set the Mode Dial to <C Press the <Q> button. (7) Pressing the <Q> button enables you to set the following: (1)Ambience-basedshots (2)Blurring/sharpening the background Drive mode <u> Single shooting: <i> Continuous shooting: <Q> Self-timer:10sec./remote: <l>Self-timer:2sec.: 2Shooting Portraits The further the distance between the subject and background, the better Use a telephoto lens Focus the face 3Shooting Landscapes With a zoom lens, use the wide-angleend Shooting night scenes 4Shooting Close-ups Use a simple background Move as close as possible to the subject 0.25m/0.8ft With a zoom lens, use the telephoto end 5Shooting Moving Subjects Use the center AF point to focus 6Shooting Night Portraits (With a Tripod) Use a wide-anglelens and a tripod Check the subject’s brightness Also shoot in another shooting mode FShooting Night Scenes Handheld Hold the camera firmly If you are shooting only the night scene, set Flash off For shots of people, turn on the flash GShooting Backlit Scenes Page QQuick Control 1Set the Mode Dial to a Basic Zone mode 2Press the <Q> button. (7) 3Set the function Settable Functions in Basic Zone Modes Shoot by Ambience Selection Set the Mode Dial to any of the following modes: <C 2Display the Live View image 3On the Quick Control screen, select the desired ambience Standard setting 4 Set the ambience effect Effect 5 Take the picture [Standard setting] Ambience Settings Vivid Soft Warm Intense Shoot by Lighting or Scene Type Default setting Light/scene-based Light/scene- based shots 1Set the Mode Dial to any of the following modes: <2>, <3>, <4> or <5 3On the Quick Control screen, select the lighting or scene type Lighting or Scene Type Settings Daylight Shade Cloudy Tungsten light xImage Playback Play back the image Select an image Exit the image playback Page d: Program AE Set the Mode Dial to <d Focus the subject 3 heck the display Change the ISO speed or use the built-inflash The program can be shifted. (Program shift) Differences Between <d> and <A> (Scene Intelligent Auto) 3Setting the Image-RecordingQuality Select [Image quality] Select the image-recordingquality Guide to Image-recordingQuality Settings (Approx.) What’s the difference between 7and 8 I was able to take more shots than the number of possible shots indicated Does the camera display the maximum burst When should I use 1 About About 1+73 i: Changing the ISO SpeedN ISO Speed Guide Press the <i> button. (9) ISO speed Set the ISO speed ISO [AUTO] 3Setting the Maximum ISO Speed for [ISO Auto]N ISO Auto AOptimal Image Characteristics for the SubjectN RLandscape SNeutral UFaithful VMonochrome WUser Def f: Changing the Autofocus OperationN 1 On the lens, set the focus mode switch to <AF 2Press the <Zf> button AF operation 3Select the AF operation AI Servo AF for Moving Subjects AI Focus AF for Automatic Switching of AF Operation SSelecting the AF PointN Press the <S> button. (9) Select the AF point When shooting a portrait up close, use One-ShotAF and focus the eyes If it is difficult to focus, select and use the center AF point AF-AssistBeam with the Built-inFlash AF Operation and Maximum Lens Apertures With maximum apertures up to f/5.6: With maximum apertures up to f/2.8: Lenses not Enabling Cross-TypeFocusing with all AF Points Subjects Difficult to Focus MF: Manual Focusing Set the lens focus mode switch to <MF iContinuous Shooting Press the <YiQ> button Select <i Also set the AF operation (p.95) matching the subject •For a moving subject Page jUsing the Self-timer 1 Press the <YiQ> button. 2 Select the self-timer Q: 10-sec. self-timer l: 2-sec. self-timer (p.140) q: 10-sec. self-timerplus DUsing the Built-inFlash 1 Press the <D> button buSY BUSY Effective Flash Range In bright light, decrease the ISO speed Detach the lens hood and keep at least 1 meter/3.3 feet away from the subject 3Red-eyeReduction Red-eye reduc Page cAbout the Main Dial Pointer s: Convey the Subject’s Movement Set the Mode Dial to <s Set the desired shutter speed To freeze the motion of a fast-movingsubject To blur a running child or animal and convey an impression of motion To blur a flowing river or fountain DUsing the Built-inFlash f: Changing the Depth of Field Set the Mode Dial to <f Set the desired aperture Set the aperture so that the shutter speed display does not blink 30 1: Flash control Depth of Field PreviewN a: Manual Exposure 1Set the Mode Dial to <a 2Set the shutter speed and aperture 3Focus the subject 4Set the exposure and take the picture IUsing the Built-inFlash BULB: Bulb Exposures BULB qChanging the Metering ModeN Select [Metering mode] Metering mode Set the metering mode qEvaluative metering eCenter-weightedaverage metering Metering Range During Live View Shooting Spot metering Setting Exposure CompensationN OSetting Exposure Compensation Making it brighter: Making it darker: yFlash Exposure Compensation Select [y] X[Flash exposure comp.] will be displayed at the bottom Set the exposure compensation amount 3Auto Exposure BracketingN Select [Expo.comp./AEB] Expo.comp./AEB 2 Set the AEB range Canceling AEB Using AEB with continuous shooting Using AEB with <u> single shooting Using AEB with the self-timeror a remote controller (sold separately) ALocking the ExposureN Press the <A> button. (0) 3Recompose and take the picture AE Lock Effects ALocking the Flash ExposureN 1Press the <D> button Press the <A> button. (8) 3Auto Correction of Brightness and ContrastN 3Noise Reduction SettingsN High ISO Speed Noise Reduction Select [High ISO speed NR] High ISO speed NR Set the setting Long Exposure Noise Reduction 1Select [Long exp. noise reduction] Long exp. noise reduction 2 Set the setting [Auto] [Enable] Peripheral Illumination Correction 1Select [Lens aberration correction] Lens aberration correction 2Select the setting Correction data available Chromatic Aberration Correction 1 Select the setting Check that [Correction data available Select [Chromatic aberration], then press <0 About the Lens Correction Data ACustomizing Image CharacteristicsN Sharpness Contrast Select a parameter Set the parameter Parameter Settings and Effects Adjusts the sharpness of the image Adjusts the image contrast and the vividness of colors Saturation The image’s color saturation can be adjusted VMonochrome Adjustment Filter effect Toning effect kFilter Effect lToning Effect ARegistering Preferred Image CharacteristicsN Page B: Matching the Light SourceN Press the <WB> button White balance Select the white balance OCustom White Balance 2Select [Custom White Balance] Custom White Balance 3Import the white balance data COPY4 Select the custom white balance uAdjusting the Color Tone for the Light SourceN White Balance Auto Bracketing Set the white balance bracketing amount WB Shift/Bkt Bracketing Sequence 3Setting the Color Reproduction RangeN 1 Select [Color space] Color space 2Set the desired color space sRGB Mirror Lockup to Reduce Camera ShakeN Mirror lockup is enabled by setting [5: Mirror lockup] to [1: Enable] in the [54: Custom Functions (C.Fn)] (p.296) 1Focus the subject, then press the shutter button completely 2Press the shutter button completely again Page Page About Remote Live View Shooting AShooting with the LCD Monitor 1 Display the Live View image Enabling Live View Shooting Set [A: Live View shoot.] to [Enable] Battery Life with Live View Shooting Information Display Scene Icons Final Image Simulation Final Image Simulation During Live View Shooting Shooting Function Settings QQuick Control drive mode image-recording quality AMenu Function Settings Live View shooting Continuous AF Touch Shutter Grid 1l Aspect ratioN 3:2 Metering timerN Changing the Autofocus Method (AF Method) Selecting the AF Method Select the AF method u(face)+Tracking: c 1Display the Live View image Page FlexiZone - Multi: o 2Select the AF zone. N FlexiZone - Single: d 2 Move the AF point Notes About [u+Tracking], [FlexiZone - Multi], and [FlexiZone - Single] AF Operation Shooting conditions that make focusing difficult Quick Mode: f 2 Select the AF point. N Page xShooting with the Touch Shutter Enable the touch shutter 3 Tap the screen to shoot Page MF: Focus Manually 1 Set the lens focus mode switch to <MF Display the magnifying frame Move the magnifying frame Magnify the image Live View Shooting Cautions Page MEMO Page About Full HD kShooting Movies Autoexposure Shooting Set the power switch to <k Set the shooting mode Movie Servo AF: Enable For details, refer to the Speedlite’s instruction manual Page Manual Exposure Shooting 2Set the Mode Dial to <a 3Set the shutter speed and aperture 4 Set the ISO speed 5 Focus and shoot the movie ISO speed during manual-exposureshooting 54: Custom Functions (C.Fn) 2: ISO expansion 1: On Page Notes on Movie Shooting Final image simulation for movie shooting Shooting Still Photos Page quality (still photos) movie-recording size video snapshots 3Exit the setting 3Setting the Movie-recordingSize Z2: Movie rec. size ****x 52: Video system Image size About Movie Files Exceeding 4 GB Movie Shooting Time Limit 3Shooting Video Snapshots Video Snapshot Album Concept Setting the Video Snapshot Shooting Duration Select [Video snapshot] Select [Enable] 3 Select [Album settings] Album settings Select [Create a new album] Select [Create a new album], then press <0 Select the Snapshot length Creating a Video Snapshot Album 7Shoot the first video snapshot 8Save as a video snapshot album Save as album 9Continue to shoot more video snapshots Options in Steps 8 and [Playback video snapshot] Operations Adding to Existing Album 1Select [Add to existing album] Add to existing album 2Select an existing album 3 Shoot the video snapshot Playing an Album Play back the movie Select the album 3Play back the album Editing an Album 1On the playback panel, select [X] (Edit) 2Select an editing operation 3Save the edited album 3Movie Menu Function Settings Z1/Z2 [Z1] menu [Z2] menu Movie Servo AF Page Movie recording size Sound recordingN [Sound rec./Rec. level] options [Manual] [Disable] [Wind filter] [Attenuator] Sound recording Movie Shooting Cautions Page Cautions when [Movie servo AF] is set to [Enable] Page Page Handy Features 3Disabling the Beeper Beep 3Card Reminder Release shutter without card 3Setting the Auto Power-offTime 3Adjusting the L D Monitor Brightness LCD brightness 3Creating and Selecting a Folder Creating a Folder Select [Select folder] Select folder Select [Create folder] Selecting a Folder About Folders Creating Folders with a Personal Computer 3File Numbering Methods IMG_0001.JPG Page 3Setting Copyright InformationN Select [Copyright information] Select the option to be set 3 Enter text 4 Exit the setting Text Entry Procedure Moving the cursor: Entering text: Changing the entry mode: Touch control: Disable 3Auto Rotation of Vertical Images Auto rotate [On [Off] BChecking Camera Settings Settings display 3Reverting the Camera to the Default SettingsN Select [Clear settings] Clear settings Select [Clear all camera settings] Select [Clear all camera settings], then press <0 Page Page 3Preventing the LCD Monitor from Turning Off Automatically LCD auto off 3Changing the Shooting Settings Screen Color 3Setting the FlashN EX-series Speedlite compatible with this function is attached Select [Flash control] [Flash firing] [Flash sync. speed in Av mode] : Auto : 1/200-1/60sec. auto : 1/200 sec. (fixed) 1/200-1/60 [Built-inflash settings] and [External flash func. setting] External flash func. setting flash settings Sample screen Shutter synchronization 1st curtain Wireless functions Flash exposure compensation Flash mode Setting the External Speedlite Custom Functions External flash C.Fn setting 1Display the Custom Function Set the Custom Function Clear the Settings fAutomatic Sensor Cleaning Cleaning the Sensor Now 1 Select [Sensor cleaning] Sensor cleaning 2 Select [Clean nowf] 3Appending Dust Delete DataN Preparation Obtain the Dust Delete Data Select [Dust Delete Data] Dust Delete Data 3Photograph a solid-whiteobject About the Dust Delete Data 3Manual Sensor CleaningN Select [Sensor cleaning] Select [Clean manually] Clean manually Clean the sensor Page Page Canceling the slave unit’s auto power off Using Wireless FlashN Slave Unit Settings and Position (1)Set the Speedlite as a slave unit (3)If you want to set the flash ratio (p.232), set the slave unit ID (5)Face the slave unit’s wireless sensor toward the camera.*2 Easy Wireless Flash Shooting Fully Automatic Shooting with One External Speedlite 1Press the <I> button to raise the built-inflash Select [Evaluative] For [E-TTLII meter.], select Select [Built-inflash settings] Select [Built-inflash settings], then press <0 Select [EasyWireless] flash EasyWireless Fully Automatic Shooting with Multiple External Speedlites Basic settings: : E-TTLII E-TTLII meter : Evaluative Custom Wireless Flash Shooting Fully Automatic Shooting with One External Speedlite and Built-inFlash Select [CustWireless] CustWireless Select [Wireless func.] Firing group [1All] Using multiple slave Speedlites as one flash unit Set [Firing group] to [1All], then take the picture [1(A:B)] Multiple slave units in multiple groups 1Select [Wireless func.] 2Set [Firing group] to [1(A:B)] A:B fire ratio : [0+3] 2 Select [Firing group] Other Settings E-TTL [Flash exp. comp.] [2exp. comp.] [1exp. comp.] Setting the Flash Output Manually for Wireless Flash [Wireless func.0] [Wireless func.0+3] Page About images shot and saved with another device xSearching for Images Quickly HDisplay Multiple Images on One Screen (Index Display) Switch to the index display 3Select an image IJump through Images (Jump Display) 1Select [Image jump w/6] Image jump w 2Select the jump method d: Display images one by one u/yMagnified View 1 Magnify the image 2 Scroll around the image dPlaying Back with the Touch Screen Press the > button to play back images Browsing Images Swipe with one finger Reduce Image (Index Display) Pinch two fingers Magnify Image Spread two fingers apart bRotating the Image Select [Rotate image] Rotate image 3 Rotate the image 3Setting Ratings Select [Rating] Select an image or movie 3Rate the image or movie Taking Advantage of Ratings QQuick Control During Playback Protect images For movies, only the functions in bold above can be set Page kEnjoying Movies Playback on a TV set (p.258, 261) Playback on the Camera’s LCD Monitor (p.250-257) Playback and Editing with a Personal Computer(p.350) kPlaying Movies Select a movie As movies cannot be played on the index display, press > to switch to the single-image Movie Playback Panel Playback with the Touch Screen Tap [7] at the center of the screen XEditing a Movie’s First and Last Scenes 1On the movie playback screen, select [X] 2Specify the part to be edited out 3 Check the edited movie 4Save the edited movie New file Overwrite 3Slide Show (Auto Playback) Select [Slide show] Slide show Select the images to be played [All images/Movies/Stills] 3 Set [Set up] as desired Set Set the [Display time], [Repeat] [Transition effect], and Background music 4 Start the slide show Start Loading image 5Quit the slide show Selecting the Background Music Select [Background music] Set [Background music] to [On], then press <0 Select the background music 3Play the background music Viewing the Images on TV Viewing on High-Definition(HD) TV Sets 1 Connectcamera. the HDMI cable to the dHDMI MINI 2 set.onnect the HDMI cable to the TV 5 Press the <x> button Using HDMI CEC TV Sets 1 Set [Ctrl over HDMI] to [Enable] Ctrl over HDMI 2Connect the camera to a TV set 3Press the camera’s <x> button Movie playback menu Press the remote control’s Enter button Return > button Viewing on Non High-Definition(HD) TV Sets 1 Connect the stereo AV cable AVC- DC400ST (sold separately) to the camera Canon 2 Connectset. the AV cable to the TV KProtecting Images 3Protecting a Single Image 1 Select [Protect images] Select [Select images] Select images 3Protecting All Images in a Folder or on a Card All images in folder All images on card 1: Protect images Unprotect all images in folder LErasing Images JPEG images Erasing a Single Image Play back the image to be erased Press the <L> button 2Select [Select and erase images] Select [Select and erase images], then press <0 3Select the images to be erased 4Erase the image 3Erasing All Images in a Folder or on a Card B: Shooting Information Display Sample Image Taken in a Creative Zone Mode Sample Image Taken in a Basic Zone Mode Sample Movie About the Highlight Alert About the Histogram [Brightness] Display [RGB] Display Page UCreative Filters Select [Creative filters] Creative filters 3 Select a filter 4 Adjust the filter effect 5 Save the image Creative Filter Characteristics Grainy B/W Soft focus Fish-eyeeffect Art bold effect Water painting effect Toy camera effect Miniature effect SResize JPEG cand RAW images cannot be resized Select [Resize] Resize 3Select the desired image size Resize Options According to Original Image Size About Image Sizes ***M ****x Page Preparing to Print Connecting the Camera to a Printer 1Set the camera’s power switch to <2 2 Set up the printer 3 Connect the camera to the 6 Play back the image wPrinting 1Select the image to be printed 2 Press <0 3 Select [Paper settings] Paper settings QSetting the Paper Size YSetting the Paper Type USetting the Page Layout 4 Set the printing effects (image optimization) What is displayed on the screen 5Set the date and file number imprinting 6Set the number of copies 7Start printing Print eAdjustment of Printing Effects Brightness Adjust levels kBrightener Red-eyecorr Trimming the Image 1On the print settings screen, select [Trimming] 2Set the trimming frame size, position, and aspect ratio Changing the trimming frame size Moving the trimming frame Page WDigital Print Order Format (DPOF) Setting the Printing Options Select [Print order] Print order Select [Set up] Sel.Image Print Ordering [Standard] [Both] [Index] Byn Mark all in folder WDirect Printing with DPOF 1Prepare to print Under the [x1] tab, select [Print order] Select [Print] 4Set the [Paper settings] (p.278) pSpecifying Images for a Photobook Specify One Image at a Time Select [Photobook Set-up] [Photobook Set-up],then press <0 3Select the image to be specified Specifying All Images in a Folder or on a Card Page 3Setting Custom FunctionsN 1Select [Custom Functions (C.Fn)] Custom Function number 2 Select the Custom Function number 3Change the setting as desired Clearing All Custom Functions Custom Functions C.Fn I: Exposure C.Fn II: Image C.Fn III: Autofocus/Drive C.Fn IV: Operation/Others 3Custom Function SettingsN C.Fn I: Exposure C.Fn-1Exposure level increments C.Fn-2ISO expansion C.Fn II: Image C.Fn-3Highlight tone priority C.Fn III: Autofocus/Drive C.Fn-4 AF-assistbeam firing C.Fn-5Mirror lockup C.Fn IV: Operation/Others C.Fn-6Shutter/AE lock button C.Fn-7Assign SET button C.Fn-8LCD display when power ON 3Registering My MenuN Select [My Menu settings] My Menu settings Select [Register to My Menu] Select [Register to My Menu], then press <0 Page Certification Logo Using a Household Power Outlet Connect the power cord Connect the DC Coupler Insert the DC Coupler Push in the DC cord Remote Control Shooting Remote Controller RC-6(Sold Separately) FRemote Switch RS-60E3(Sold Separately) Using the Eyepiece Cover Remove the eyecup Attach the eyepiece cover External Speedlites EOS-dedicated, EX-seriesSpeedlites Canon Speedlites Other Than the EX-series Using Non-CanonFlash Units Sync Speed Cautions for Live View shooting Using Eye-FiCards Insert an Eye-Ficard (p.31) Select [Eye-Fisettings] Eye-Fi settings 5Check the [Access point SSID:] Access point SSID: 6 Take the picture Not connected Connecting Page Function Availability Table According to Shooting Mode Page System Map Bundled Accessories Page 3Menu Settings For Viewfinder Shooting and Live View Shooting Shooting 1 (Red) Shooting 2 (Red) Shooting 3 (Red) ALive View Shooting (Red) Playback 1 (Blue) Playback 2 (Blue) Set-up1 (Yellow) Set-up2 (Yellow) Set-up3 (Yellow) Set-up4 (Yellow) 9My Menu (Green) kFor Movie Shooting Movie 1 (Red) Movie 2 (Red) Troubleshooting Guide The battery pack does not recharge The battery charger’s lamp blinks The battery becomes exhausted quickly The camera turns off by itself No images can be shot or recorded The card cannot be used The image is out of focus I cannot lock the focus and recompose the shot The continuous shooting speed is slow The maximum burst during continuous shooting is lower ISO 100 cannot be set ISO speed [H] (ISO 25600) cannot be set The Auto Lighting Optimizer cannot be set The built-inflash is raised by itself The built-inflash does not fire The flash always fires at full output High-speedsync cannot be set in the <f> mode The camera makes a noise when it is shaken Movie shooting stops by itself The ISO speed cannot be set for movie shooting The exposure changes during movie shooting The subject looks distorted during movie shooting The menu screen shows few tabs and options The file name’s first character is an underscore (“_”) The file name starts with “MVI_” The file numbering does not start from The shooting date and time displayed is incorrect The date and time is not in the picture [###] is displayed The LCD monitor does not display a clear image [Eye-Fisettings] does not appear Part of the image blinks in black The image cannot be erased The movie cannot be played back The movie has still moments No image appears on the TV screen My card reader does not recognize the card I cannot resize the image The shutter makes a noise during sensor cleaning Automatic sensor cleaning does not work Error Codes Specifications Page Page Page Page Page Page Page Handling precautions: EF-S18-135mm f/3.5-5.6IS STM Trademarks About MPEG-4Licensing Use of genuine Canon accessories is recommended Preventing Serious Injury or Death Preventing Injury or Equipment Damage Digital Camera Model DS126371 Systems CAUTION Page Downloading Images to a Personal Computer Download by Connecting the Camera to the Personal Computer 1Install the software (p.351) 2 Use the provided interface cable to connect the camera to your personal computer Downloading Images with a Card Reader 2 Insert the card into the card reader 3Use Canon software to download the images/movies About the Software EOS DIGITAL Solution Disk EOS Utility Digital Photo Professional ImageBrowser EX Installing the Software 1Insert EOS DIGITAL Solution Disk (CD-ROM) Canon EOS Digital Installer 2Click [Easy Installation] and follow the on-screeninstructions to install Install Software Instruction Manual Copying and Viewing the Instruction Manual PDFs Insert the [Software INSTRUCTION MANUAL] CD-ROMinto your computer Double-clickthe CD-ROMicon 3Copy the [English] folder to your computer Page Page 1: Image quality Page Page Page Basic Zone Modes Creative Zone Modes You can change the camera settings as desired to shoot in various ways Page Page Page Page Page Index Numerics