The following data is shown in information view.

 

 

 

 

 

 

 

 

 

 

 

 

Zoom Indicator

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Built-in Memory

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Display

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Macro Mode

 

 

White Balance

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Shooting Methods

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Flash

 

 

 

 

 

 

 

 

Compression

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Exposure Compensation

 

 

Resolution

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The last on/off setting of the LCD monitor is saved when the power is manually shut off. The camera will automatically restore the LCD monitor to the last setting at startup.

However, until the battery is replaced, the LCD monitor will not turn on automatically if a low battery caused the power to shut off automatically.

The image in the LCD monitor will darken when struck by direct sunlight or strong illumi- nation. This does not constitute a malfunction.

28

Using the Shutter Button

The shutter button features a two-stage action.

Pressing Halfway

Lightly press the shutter button halfway to automatically set the exposure and focus settings. The camera will beep twice and the upper indicator will shine green (red for flash) when the metering is finished.

The lower indicator will also shine orange when the camera is ready in macro mode.

Pressing Fully

Press the button all the way down to activate the shutter. The beep will sound once. The upper indicator will flash green while the image is being recorded onto the CF card.

The recorded image will be temporarily stored in the camera’s built-in memory and then be written to the CF card. As long as there is sufficient built- in memory free, the next image can be recorded immediately after the previous image.

With the LCD monitor in information view mode, you can view the status of the image being written to the CF card with the memory display (built-in) at the bottom right.

Page 31
Image 31
Canon S20 Using the Shutter Button, Pressing Halfway, Pressing Fully, Following data is shown in information view