Carrier 50PCH Appendix a Wshp Open Screen Configuration, Maintenance, System Settings, Occupancy

APPENDIX A — WSHP OPEN SCREEN CONFIGURATION (cont)

SCREEN NAME		POINT NAME	PASSWORD	EDITABLE	RANGE	DEFAULT	NOTES
			LEVEL
					Off, Fan Only,Economize,
		Operating Mode			Cooling, Heating, Cont Fan, Test,		Displays unit operating mode
					Start Delay, Dehumidify
		Fan Operating Mode			Auto/Continuous/Always On		Displays how the fan is configured
							to operate
		Occupancy Status			Unoccupied/Occupied		Displays the current occupancy status
					Always Occupied/Local Schedule/
					BACnet Schedule/BAS Keypad/		Displays the origin of the
		Occupancy Control			Occupied Contact/Holiday Schedule/
							occupancy control
					Override Schedule/Pushbutton
					Override/Unoccupied None
		Outside Air			° F		Displays OAT (Viewable only if OAT
		Temperature					is a network broadcast)
		SPT			° F		Displays SPT
		SPT Status			Normal/Above Limit/Below		Displays the SPT status
					Limit/Sensor Failure
		SPT Sensor Status			Inactive/Connected		Displays the connection status
							of the Rnet sensor
		Condensate Overflow			Normal/Alarm		Displays the status of the
							condensate overflow
		Cooling Set Point			° F		Displays the actual set point
							being used for cooling control
		Heating Set Point			° F		Displays the actual set point
	Unit		No Password				being used for heating control
Maintenance			required		° F		Displays the offset values from the Rnet
		Set Point Adjustment					user set point adjustment that is being
							applied to the configured set points
		Auxiliary Heat Control			° F		Displays the calculated set point being
		Set Point					used for auxiliary heating control
		H2O Economizer			° F		Displays the calculated set point being
		Control Set Point					used for economizer control
		Calculated IAQ/					Displays the ventilation damper
		Ventilation Damper			%
							position calculated by the DCV control
		position
		Active Compressor			0/1/2		Displays the actual number of
		Stages					compressor stages operating
		SAT			° F		Displays SAT
		Reset Filter Alarm		X	No/Yes		Used to reset the filter alarm timer after
							the filter has been cleaned or replaced
		Overflow Contact			Closed/Open		Displays the state of the condensate
							overflow switch contact
		Occupancy Contact			Closed/Open		Displays the state of the external/
							remote occupancy input switch contact
					Inactive/Occupied/		Provides capability to force the
		BAS/Keypad Override		X		Inactive	equipment to operate in an
					Unoccupied
							occupied or unoccupied mode
		OAT Input			N/A / Network		Displays if an OAT value is being
							received from the Network
		BACnet		X			See TPI
		Keypad Configuration		X			Mapping
System Settings		Password		X			Changes password
		Network		X			See TPI
		BACnet Time Master		X			See TPI
		Clock Set		X			Changes clock/time setting
		Override Schedules			Inactive/Active Occupied
		Pushbutton Override			Inactive/Active Occupied
Occupancy		Keypad Override	No Password		Inactive/Active Occupied/Active		Used to display the active and
					Unoccupied
Maintenance			required				inactive occupancy control inputs
		Schedules			Inactive/Active Occupied
		Occupancy Contact			Inactive/Active Occupied
		BAS on/off			Inactive/Active Occupied
		Local Occupancy		X	Disable/Enable	Enable
		Schedules
		Local Holiday	User/Admin	X	Disable/Enable	Disable	Used to define which occupancy inputs
Schedule		Schedules
			Password level				are used to determine
Configuration		Local Override
			access	X	Disable/Enable	Disable	occupancy mode.
		Schedules
		BACnet Occupancy		X	Disable/Enable	Disable
		Schedules
	LEGEND
BAS — Building Automation System
DCV	— Demand Controlled Ventilation
IAQ	— Indoor Air Quality
OAT	— Outdoor Air Temperature
RH	— Relative Humidity
SAT — Supply Air Temperature
SPT	— Space Temperature
TPI	— Third Party Integration

44