Versa•Touch2®
VERSA•TOUCH2 Operation
Fan Control | SEND SIGNAL |
| LIGHT | ||
To start the fan. Press the selected speed button to run the fan at the desired speed. | LED |
|
| ||
LO=Low speed MED=Medium speed | HI=High speed |
|
|
|
|
To turn off the fan. Press the FAN OFF | button. |
|
|
|
|
Airflow Direction |
| MED |
|
| |
To reverse the airflow press the REVERSE button. Reverse operates at any speed whether fan |
|
|
|
| |
is on or off. The fan returns to its set speed after reversing. | LO |
| HI | ||
Light Control |
|
|
|
|
|
Turn the light on or off independently from the fan by pressing the LIGHT button. Keep |
|
|
|
| |
pressing the button in excess of 0.7 seconds, it becomes a dimmer. The light varies from |
|
|
|
| |
‘bright’ to ‘dim’ over approximately 8 seconds. This sequence will reverse the light when it |
|
|
|
| |
reaches the brightest or dimmest level if you continue to hold the LIGHT button. Release |
|
|
| FAN | |
the button when the desired level is reached. |
|
|
| STOP | |
Memory Feature |
| REVERSE |
|
| |
The last light function and fan speed will resume when power is turned back on. |
|
|
Auto Resume
Quick (pressing less than 0.7 seconds) on/off operation of the LIGHT button maintains the desired brightness level set previously.
VERSA•TOUCH2 ♦ Changing FREQuency SETTING
Note: All fans leave the factory set to ‘00000’.
You will only have to change the dip switch settings in the remote if you are using more than one fan in the same area and want to control them separately.
Step 1. At the circuit breaker or fuse box, turn the power off for the fan you want to change.
Step 2. Open the battery door of the Versa•Touch control and remove the batteries.
Step 3. Change the dip switch settings, assuring that they are different from the previously installed Versa•Touch fan.
Step 4.
Step 5. At the circuit breaker or fuse box, turn the power back on for | dip switch | |||
set to ‘10000’ | ||||
the fan whose frequency you are changing. |
| |||
|
|
| ||
Step 6. Within 20 seconds of restoring power, push the Hi, Med, and |
|
| ||
Lo buttons (in that order). | WITHIN 20 SECONDS OF |
| ||
|
| |||
Note: You may want to label your controls to | TURNING THE FAN ON, |
| ||
PRESS IN THIS ORDER TO | ||||
assure you do not mix them up. | ||||
SET NEW FREQUENCY: |
| |||
|
| |||
|
| 1. HI |
| |
WARNING: Do not turn the power off at the circuit breaker, |
| 2. MED | 3 | |
then back on, for the previously installed Versa•Touch 2 |
| 3. LO | ||
fan(s), as you may inadvertantly change the frequency set- |
|
|
| |
tings for it as well. |
|
|
|
versa•touch 2
control
(back)
dip switch
set to ‘01001’
2
1
VERSA•TOUCH2 ♦ IF FAN DOES NOT WORK
If the fan is not functioning after installation: |
|
|
| 2 | |
|
|
|
| ||
Step 1. Check to make sure that batteries are installed correctly |
|
|
|
| |
in the control. |
|
|
|
| |
Step 2. Turn the power off to the fan (from the circuit breaker) |
|
| 3 | 1 | |
for at least 5 seconds. |
|
|
|
| |
Step 3. Turn the power back on (at the circuit breaker) and push |
| PRESS IN THIS ORDER TO SET NEW | |||
the Hi, Med, and Low |
| ||||
Circuit breaker | FREQUENCY: |
| |||
Step 4. The fan should now function properly. |
| ||||
or fuse box | 1. HI | 2. MED | 3. LO | ||
|
13