Cateye CC-TR200DW (V2c) Replacing battery, Trouble on operation, Speed sensor, ENG-36

Trouble on operation

Trouble		Check Items			Remedy
Pressing the SSE button	Check whether the auto-		When	illuminates, the auto-mode
does not start/stop	mode is turned on (with		is on; you cannot start or stop mea-
measurement.	illuminating).		surement by pressing the button.
			Turn off the auto-mode. (See “Setting
			the auto-mode” on page 31.)
The speed/cadence sen-			The battery for the speed sensor is
sor ID synch failed.			possibly depleted.
			After replacing the battery with a new
			one (CR2032), check the sensor ID
			again (page 28).
Lap data cannot be	Have you already com-		Delete data files that contain several laps
stored.	pleted 99 laps?		from the file view (page 26) in order to
			obtain free space for lap recording.
	Is the lap time over 100		With the recording range exceeded, the
	hours (Or is the trip lap dis-		lap cannot be measured.
	tance over 9999.99 km)?		Perform the resetting operation (page
			16) for further measurements.
	Is it immediately after		You cannot record the lap for 5 sec-
	pressing the LAP button?		onds immediately after pressing the
			LAP button.
Abnormal values ap-	Are there any objects emit-		Keep the unit away from any object that
pear.	ting electromagnetic waves		may be causing interference, and re-
	(railway tracks, transmit-		set the data (page 16).
	ting stations for television,

Replacing battery

The product comes with factory-installed batteries. When a battery is empty, replace it with a new one according to the following instructions.

Warning!!! :

Safely dispose of the old batteries, and do not place them within reach of children. If a battery is swallowed, consult a doctor immediately.

*When any battery for the computer, or speed/cadence sensor depleted, we recom- mend replacing all batteries at the same time.

*The battery life shown in this manual is not definitive and it varies depending on the use environment.

*The battery cover sealing is critical to maintain the waterproof feature.

Clean any contamination on the battery cover or the seal, and check whether it seals correctly.

Computer Close

Battery life: Approx. 1 years when used for 1 hour per day.

* When the remaining battery capacity is low, lights up. Open

1. Remove the battery cover on the back of the computer using a coin, or the equivalent.

2.Insert new lithium batteries (CR2032) with the (+) sign upward, and close the battery cover firmly.

3.After replacement, be sure to perform the restarting operation

(page 10), and set the date and time. CR2032

ENG

	etc.) nearby?
In menu mode, cannot	Is it currently measure-			Only top menu can be viewed during
change settings.	ment?			measurement.
	When the auto-mode is			Keep the unit away from any object that
	turned on (with		illumi-	may be causing interference with elec-
	nating), it may enter the mea-			tromagnetic waves.
	surement mode due to elec-
	tromagnetic waves.
	Is it the target zone or the			To change the target zone and
	measurement unit that can-			measurement unit, the resetting
	not be changed?			operation is required.
				Stop measurement, and perform the
				resetting operation (page 16).
Measurement data can-		Has the total number of laps		Delete data files that contain several
not be stored on the file		reached 99 points?		laps from the file view (page 26) in or-
view.				der to obtain free space for lap record-
				ing.

Speed sensor

Battery life: Approx. 1 years when used for 1 hour per day.

1.Remove the battery cover on the speed sensor using a coin, or the equivalent.

2.Insert new lithium batteries (CR2032) with the (+) sign upward, and close the battery cover firmly.

3.After replacement, be sure to press the RESET button on the speed sensor, and check that the positions of the magnet and sensor are correct and they are secured firmly.

Close RESET

Open

CR2032

ENG-36 ENG-37