Troubleshooting and handling care

Troubleshooting

Problems noted in the following chart are not disorders. Prior to seeking repair, read the contents of the entire chart first.

Problem

Item to check

Countermeasure

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Display does not appear.

Is the power supply connected?

Connect the AC adaptor correctly.

 

 

 

 

 

 

 

(see page 14)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Is the power switch on?

Turn the power on.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Isn't the cable of the AC Adapter

Replace the AC Adapter if its inte-

 

 

damaged?

 

rior circuit or the cable is dam-

 

 

 

 

 

 

 

aged.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Printer does not work.

Didn't you select "not to use" the

Set the select switch No.4 to OFF.

 

 

printer with the selector switch on

(see page 8)

 

 

 

 

 

 

 

 

 

the back panel of the control unit?

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Is the

 

 

 

symbol shown on the

Press the

 

 

button on the Con-

 

 

 

 

 

 

 

 

 

 

 

 

 

 

LCD?

 

trol Unit to let the

 

 

symbol

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

show up. But if the select switch

 

 

 

 

 

 

 

No.4 on the back of the control

 

 

 

 

 

 

 

unit is ON, the

 

 

symbol doesn't

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

appear even if you press the but-

 

 

 

 

 

 

 

ton.

 

 

 

 

 

 

 

 

 

 

 

 

 

Isn't the paper jammed?

Remove the jammed paper. (see

 

 

 

 

 

 

 

page 51)

 

 

 

 

 

 

 

 

 

 

 

 

Date memory is incorrect.

Did you set the date?

Set the date correctly (page 49)

 

 

 

 

 

 

Are the backup batteries installed?

Load the backup batteries. (see

 

 

If not, the date memory is lost each

page 8)

 

 

 

 

 

 

 

 

 

time you turn off the power.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Isn't the

symbol shown on the

Replace the backup batteries, be-

 

 

LCD?

 

cause they have worn out. (see

 

 

 

 

 

 

 

page 8)

 

 

 

 

 

 

 

 

 

 

 

 

ERROR or irregular display ap-

Isn't the data card reversed?

Hold the card yellow arrow side

 

pears when you insert the data

 

 

 

 

 

up, and insert to the direction of

 

card.

 

 

 

 

 

arrow.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Didn't you insert the card too

Insert the card slowly.

 

 

 

 

quickly?

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Didn't you specify two or more pro-

Refer to P.42~43 and specify the

 

 

grams, or open unnecessary holes?

program and conditions correctly.

 

 

 

 

 

The pulse rate is not displayed, re-

Is the pulse sensor attached cor-

Insert the sensor plug securely into

 

maining "0".

rectly to your earlobe?

the sensor jack, and check the

 

 

 

 

 

 

 

pulse sensor function according to

 

 

Is the sensor plug completely in-

page 13. If the sensor cable proves

 

 

serted into the sensor jack?

to be broken, replace the pulse

 

 

 

 

 

 

 

sensor (part #7801101).

 

 

 

 

 

 

 

The pulse rate increases abnor-

Is the pulse sensor correctly at-

Attach the sensor correctly to your

 

mally.

tached to your earlobe?

earlobe and take care not to swing

 

 

 

 

 

 

 

the sensor or sensor cable during

 

 

Isn't the sensor cable damaged?

the exercise. If the sensor cable

 

 

 

 

 

 

 

proves to be damaged, replace the

 

 

 

 

 

 

 

whole pulse sensor with a new one.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Problem

Item to check

Countermeasure

 

 

 

 

 

The evaluation of fitness level

Is the weight unit correct?

Set the weight unit correctly. (see

seems incorrect.

 

 

page 8)

 

 

 

 

 

 

 

 

Did you select the correct fitness

Check the selector switch on the

 

 

level evaluation table?

back panel of the control unit. (see

 

 

 

 

page 8~9)

 

 

 

 

 

The program is suspended half-

Isn't the upper pulse limit alarm

Input your age correctly to prevent

way.

ringing due to the excess of your

the alarm from ringing unduly.

 

 

pulse rate during the exercise?

 

 

 

 

 

 

 

 

Buzzer keeps sounding.

Isn't the pulse limit setting too low

 

 

 

 

 

due to an incorrect age input?

 

 

 

 

 

 

 

 

The pitch sound doesn't ring.

Is the

symbol shown on the

Press the

button on the control

 

 

LCD?

 

unit to let the

symbol show up.

 

 

 

 

 

 

Check if sensor plug is completely

Unit does not give pitch sound if

 

 

connected.

 

plug is out of jack.

 

 

 

Clattering noise is heard with the

Are the pedals firmly attached to

Attach the pedals firmly.

pedal rotation.

the crank? If not, noise may be pro-

 

 

 

 

 

duced.

 

 

 

 

 

 

 

 

 

 

 

Handling

For longer use of the Ergociser™ EC-3700, observe the following precautions.

Do not disassemble the main and control units. In case of prob- lems contact your dealer where the unit was purchased.

Avoid using the Ergociser™ EC-3700 in a high temperatures or in high humidity. Also, do not splash the unit with water.

Handle the pulse sensor carefully. If strongly pulled out the cable may become disconnected.

When the EC-3700 is not in use, shut the power switch OFF and disconnect the power cord from the outlet.

Do not wipe the main unit with organic solvents such as thinner, kerosine, gasoline and alcohol. When dirty, wipe the unit with a cloth soaked in a neutral detergent, then wipe well with a dry cloth.

Do not place the EC-3700 in direct sun light.

50

51

Page 30
Image 30
Cateye EC-37OO operating instructions Troubleshooting and handling care, Handling