OPERATION

IMPORTANT SAFETY INSTRUCTIONS

WARNING

To reduce the risk of SEVERE INJURY or DEATH:

1.READ AND FOLLOW ALL WARNINGS AND INSTRUCTIONS.

2.ALWAYS keep remote controls out of reach of children. NEVER permit children to operate or play with garage door control push buttons or remote controls.

3.ONLY activate garage door when it can be seen clearly, it is properly adjusted, and there are no obstructions to door travel.

4.ALWAYS keep garage door in sight until completely closed. NO ONE SHOULD CROSS THE PATH OF THE MOVING DOOR.

5.If possible, use emergency release handle to disengage trolley ONLY when garage door is CLOSED. Weak or broken springs or unbalanced door could result in an open door falling rapidly and/or unexpectedly.

6.NEVER use emergency release handle unless garage doorway is clear of persons and obstructions.

7.NEVER use handle to pull garage door open or closed. If rope knot becomes untied, you could fall.

8.If one control (force or travel limits) is adjusted, the other control may also need adjustment.

9.After any adjustments are made, the safety reversal system MUST be tested.

10.Safety reversal system MUST be tested every month. Garage door MUST reverse on contact with 38 mm obstacle on the floor.

11.ALWAYS KEEP GARAGE DOOR PROPERLY BALANCED (see page 3). An improperly balanced door may not reverse when required and could result in severe injury or death.

12.All repairs to cables, spring assemblies and other hardware, all of which are under EXTREME tension, MUST be made by a trained door systems technician.

13.ALWAYS disconnect electric power to garage door opener before making any repairs or removing covers.

14.SAVE THESE INSTRUCTIONS.

Using Your Garage Door Opener

Your Security✚® opener and hand-held remote control have been factory-set to a matching code which changes with each use, randomly accessing over 100 billion new codes. Your opener will operate with up to fifty-four Security✚® remote controls and one Security✚® Keyless Entry System. If you purchase a new remote, or if you wish to deactivate any remote, follow the instructions in the Programming section.

Activate your opener with any of the following:

•The hand-held Remote Control: Hold the push button down until the door starts to move.

•The wall-mounted Door Control: Hold the push button or bar down until the door starts to move.

•The Keyless Entry (See Accessories): If provided with your garage door opener, it must be programmed before use. See Programming.

When the opener is activated

1.If open, the door will close. If closed, it will open.

2.If closing, the door will reverse.

3.If opening, the door will stop.

4.If the door has been stopped in a partially open position, it will close.

5.If obstructed while closing, the door will reverse.

6.If obstructed while opening, the door will stop.

7.The optional Protector System® uses an invisible

beam, which, when broken by an obstruction, causes a closing door to open and prevents an open door from closing. It is STRONGLY RECOMMENDED for homeowners with young children.

The opener lights will turn on under the following conditions: when the opener is initially plugged in; when power is restored after interruption; when the opener is activated.

They will turn off automatically after 4-1/2 minutes or provide constant light when the Light feature on the Multi-Function Door Control is activated. Bulb size is 100 watts maximum.

Timer to close feature (ONLY available when optional Protector Systema is installed): The door can be programmed to close the door automatically in 10 seconds, 45 seconds, 2 minutes or, 3 minutes.

The Timer to close feature is preset to the off position from the factory. To activate this feature, press and hold the Lock button on the Multi-Function Door Control until the opener light blinks once (about 10 seconds). A single blink indicates that the timer is reset to 10 seconds. Repeat the procedure and the light will blink twice, resetting the timer to 45 seconds. Repeat again for a 2 minute interval, etc., up to a maximum of four blinks and 3 minutes.

To deactivate, set the timer to 3 minutes. Press and hold the Lock button on the Multi-Function Door Control again for 10 seconds. The opener light will blink 5 times. This feature is now deactivated.

32