Manuals / Brands / Household Appliance / Garage Door Opener / Chamberlain / Household Appliance / Garage Door Opener

Chamberlain 182665D Install the Header Bracket, WALL HEADER BRACKET INSTALLATION, CEILING HEADER BRACKET INSTALLATION

1 80

Download 80 pages, 6.24 Mb

INSTALLATION STEP 2

Install the Header Bracket

You can attach the header bracket either to the wall above the garage door, or to the ceiling. Follow the instructions which will work best for your particular requirements. Do not install the header bracket over drywall. If installing into masonry, use concrete anchors (not provided).

WALL HEADER BRACKET INSTALLATION

•Center the bracket on the vertical centerline with the bottom edge of the bracket on the horizontal line as shown (with the arrow pointing toward the ceiling).

•Mark the vertical set of bracket holes. Drill 3/16" pilot holes and fasten the bracket securely to a structural support with the hardware provided.

HARDWARE SHOWN ACTUAL SIZE

Lag Screw 5/16"-9x1-5/8"

CEILING HEADER BRACKET INSTALLATION

•Extend the vertical centerline onto the ceiling as shown.

•Center the bracket on the vertical mark, no more than 6" (15 cm) from the wall. Make sure the arrow is pointing away from the wall. The bracket can be mounted ﬂush against the ceiling when clearance

is minimal.

•Mark the side holes. Drill 3/16" pilot holes and fasten bracket securely to a structural support with the hardware provided.

Wall Mount

Optional

Mounting Holes

- Header Wall -

2x4 Structural

SupportHeader Bracket

Horizontal

Line

Highest Point of

Garage Door Travel

Vertical

Centerline

of Garage

Door

Lag Screws 5/16"-9x1-5/8"

Door Spring

- Garage Door -

Vertical

Centerline

of Garage Door

- Finished Ceiling -

Vertical Centerline

of Garage Door

	Header
	Bracket
	6" (15 cm) Maximum
	Door
Ceiling Mounting Holes	Spring

Lag Screws 5/16"-9x1-5/8"

- Header Wall -

Garage Door	Vertical
	Centerline
	of Garage Door

13

Contents

For Residential Use Only Introduction Assembly Installation Adjustment Operation Preparing Your Garage Door Tools needed Planning Planning (Continued) Carton Inventory Hardware Inventory Assemble the Rail & Install the Trolley Fasten the Rail to the Motor Unit Install the Idler Pulley Install the Belt and Attach the Belt Cap Retainer WARNING Determine the Header Bracket Location Install the Header Bracket Attach the Rail to the Header Bracket Position the Opener Hang the Opener Install the Door Control Install the Lights Attach the Emergency Release Rope and Handle Electrical Requirements Install The Protector System® INSTALLING THE BRACKETS Garage door track installation (preferred): Wall installation (Figures 2 and 3): Floor installation (Figure 4): MOUNTING AND WIRING THE SAFETY REVERSING SENSORS Mounting: Option A - Installation Without Pre-Wiring: Option B - Pre-WiredInstallation: Connect to garage door opener: ALIGNING THE SAFETY REVERSING SENSORS TROUBLESHOOTING THE SAFETY REVERSING SENSORS Fasten the Door Bracket ONE-PIECEDOORS Metal Doors: Connect Door Arm to the Trolley ALL ONE-PIECEDOORS 1. Assemble the door arm, Figure 5: IMPORTANT: 2.Adjustment procedures, Figure 6: •Open door adjustment: decrease UP travel limit Adjust the UP and DOWN Travel Limits Adjust the Force Test the Safety Reversal System Test The Protector System® IMPORTANT SAFETY INSTRUCTIONS Using Your Garage Door Opener Using the Wall-MountedDoor Control To Open the Door Manually CARE OF YOUR OPENER LIMIT AND FORCE ADJUSTMENTS: THE REMOTE CONTROL BATTERY MAINTENANCE SCHEDULE Every Month HAVING A PROBLEM 2.My remotes will not activate the door: 5.My lights will not turn off when door is open: 6.My motor unit hums brieﬂy: Diagnostic Chart To Add or Reprogram a Hand-HeldRemote Control To Erase All Codes From Motor Unit Memory *3-ButtonRemotes To Add, Reprogram or Change a Keyless Entry PIN Rail Assembly Parts Motor Unit Assembly Parts ACCESSORIES 953CD 3-ButtonSECURITY✚® Remote Control: 956CD CHAMBERLAIN® SERVICE IS ON CALL OUR LARGE SERVICE ORGANIZATION SPANS AMERICA AND CANADA INSTALLATION AND SERVICE INFORMATION IS AS Pour Résidences Seulement TABLE DES MATIÈRES Introduction Montage Pose Réglages Préparation de votre porte de garage Outils nécessaires Planiﬁcation Planiﬁcation (Suite) Inventaire de la boîte d’emballage Inventaire des ﬁxations MONTAGE - 1re OPÉRATION Montage du rail et pose du chariot MONTAGE - 2e OPÉRATION Fixation du rail au moteur MONTAGE - 3e OPÉRATION Pose de la poulie MONTAGE - 4e OPÉRATION Pose de la courroie et ﬁxation du capuchon de retenue de la courroie MONTAGE - 5e OPÉRATION Régler la tension LA POSE ou MORTELLES : POSE – 1re OPÉRATION POSE - 2e OPÉRATION Pose du support de linteau POSE - 3e OPÉRATION Fixation du rail sur le support de linteau POSE - 4e OPÉRATION Positionnement de l'ouvre-porte POSE - 5e OPÉRATION Accrochage de l'ouvre-porte POSE - 6e OPÉRATION Pose de la commande de porte POSE - 7e OPÉRATION Pose des ampoules POSE - 8e OPÉRATION POSE - 9e OPÉRATION Exigences électriques POSE - 10e OPÉRATION Pose du Système Protector® POSE DES SUPPORTS S’assurer que l’ouvre-porteest hors tension Pose murale (Figures 2 et 3) : Pose au sol (Figure 4) : MONTAGE ET CÂBLAGE DES DÉTECTEURS INVERSEURS DU SECURITIÉ Montage : Option A - Installation sans les câbles préinstallés : Option B - Installation pré-câblée : Connexion à l’ouvre-portede garage : DÉPANNAGE DES DÉTECTEURS INVERSEURS DU SÉCURITÉ POSE - 11e OPÉRATION Fixation du Support de Porte PORTES RIGIDES POSE - 12e OPÉRATION Fixation de la biellette au chariot POUR TOUTES LES PORTES RIGIDES 1. Assemblage des biellettes, Figure 5 : IMPORTANT : 2.Méthodes de réglage, Figure 6 : •Réglage de l'ouverture de la porte : diminuer la course d’OUVERTURE RÉGLAGES - 1re OPÉRATION RÉGLAGES - 2e OPÉRATION Réglage de la force RÉGLAGES - 3e OPÉRATION Essai du système d’inversion de sécurité RÉGLAGES - 4e OPÉRATION Essai du Systéme Protector® FONCTIONNEMENT ou DE MORT :