Manuals / Brands / Household Appliance / Garage Door Opener / Chamberlain / Household Appliance / Garage Door Opener

Chamberlain 182665D Planning (Continued), ONE-PIECEDOOR WITH TRACK, ONE-PIECEDOOR INSTALLATIONS, ONE-PIECEDOOR WITHOUT TRACK

1 80

Download 80 pages, 6.24 Mb

Planning (Continued)

ONE-PIECE DOOR INSTALLATIONS

•Generally, a one-piece door does not require reinforcement. If your door is lightweight, refer to the information relating to sectional doors in Installation Step 11.

•Depending on your door’s construction, you may need additional mounting hardware for the door bracket (Step 11).

Without a properly working safety reversal system, persons (particularly small children) could be SERIOUSLY INJURED or KILLED by a closing garage door.

•The gap between the bottom of the garage door and the ﬂoor MUST NOT exceed 1/4" (6 mm). Otherwise, the safety reversal system may NOT work properly.

•The ﬂoor or the garage door MUST be repaired to eliminate the gap.

ONE-PIECE DOOR WITHOUT TRACK		FINISHED CEILING
		FINISHED CEILING
		Support bracket &
		fastening hardware
		is required.
	Rail	See page 15.
	Rail
Header Wall
			Motor unit
		Wall-Mounted
		Door Control
		Access
		Door			CLOSED POSITION
					CLOSED POSITION
			Trolley Stop Bolt Belt		Trolley
			Header	Rail
			Bracket	Rail
			Door Bracket			Emergency
	Safety Reversing Sensor					Release
	Safety Reversing Sensor			Straight	Curved	Rope &
	Gap between ﬂoor and				Curved	Handle
	Gap between ﬂoor and				Door	Handle
	bottom of door must not			Door Arm	Door
Safety Reversing Sensor	bottom of door must not			Door Arm	Arm
Safety Reversing Sensor	exceed 1/4" (6 mm).	Header	Garage		Arm
		Wall	Door

ONE-PIECE DOOR WITH TRACK

Safety

Reversing

Sensor

Gap between ﬂoor and bottom of door must not exceed 1/4" (6 mm).

Access		CLOSED POSITION
Door		CLOSED POSITION
Door		Trolley Stop Bolt		Belt	Trolley
		Trolley Stop Bolt		Belt	Trolley
		Header	Curved
		Bracket	Door Arm		Rail
		Door			Emergency
Safety		Door		Straight	Release
Safety		Bracket		Straight	Release
Reversing	Header			Door	Rope &
Sensor	Wall	Garage		Arm	Handle
		Door

5

Contents

For Residential Use Only Introduction Assembly Installation Adjustment Operation Preparing Your Garage Door Tools needed Planning Planning (Continued) Carton Inventory Hardware Inventory Assemble the Rail & Install the Trolley Fasten the Rail to the Motor Unit Install the Idler Pulley Install the Belt and Attach the Belt Cap Retainer WARNING Determine the Header Bracket Location Install the Header Bracket Attach the Rail to the Header Bracket Position the Opener Hang the Opener Install the Door Control Install the Lights Attach the Emergency Release Rope and Handle Electrical Requirements Install The Protector System® INSTALLING THE BRACKETS Garage door track installation (preferred): Wall installation (Figures 2 and 3): Floor installation (Figure 4): MOUNTING AND WIRING THE SAFETY REVERSING SENSORS Mounting: Option A - Installation Without Pre-Wiring: Option B - Pre-WiredInstallation: Connect to garage door opener: ALIGNING THE SAFETY REVERSING SENSORS TROUBLESHOOTING THE SAFETY REVERSING SENSORS Fasten the Door Bracket ONE-PIECEDOORS Metal Doors: Connect Door Arm to the Trolley ALL ONE-PIECEDOORS 1. Assemble the door arm, Figure 5: IMPORTANT: 2.Adjustment procedures, Figure 6: •Open door adjustment: decrease UP travel limit Adjust the UP and DOWN Travel Limits Adjust the Force Test the Safety Reversal System Test The Protector System® IMPORTANT SAFETY INSTRUCTIONS Using Your Garage Door Opener Using the Wall-MountedDoor Control To Open the Door Manually CARE OF YOUR OPENER LIMIT AND FORCE ADJUSTMENTS: THE REMOTE CONTROL BATTERY MAINTENANCE SCHEDULE Every Month HAVING A PROBLEM 2.My remotes will not activate the door: 5.My lights will not turn off when door is open: 6.My motor unit hums brieﬂy: Diagnostic Chart To Add or Reprogram a Hand-HeldRemote Control To Erase All Codes From Motor Unit Memory *3-ButtonRemotes To Add, Reprogram or Change a Keyless Entry PIN Rail Assembly Parts Motor Unit Assembly Parts ACCESSORIES 953CD 3-ButtonSECURITY✚® Remote Control: 956CD CHAMBERLAIN® SERVICE IS ON CALL OUR LARGE SERVICE ORGANIZATION SPANS AMERICA AND CANADA INSTALLATION AND SERVICE INFORMATION IS AS Pour Résidences Seulement TABLE DES MATIÈRES Introduction Montage Pose Réglages Préparation de votre porte de garage Outils nécessaires Planiﬁcation Planiﬁcation (Suite) Inventaire de la boîte d’emballage Inventaire des ﬁxations MONTAGE - 1re OPÉRATION Montage du rail et pose du chariot MONTAGE - 2e OPÉRATION Fixation du rail au moteur MONTAGE - 3e OPÉRATION Pose de la poulie MONTAGE - 4e OPÉRATION Pose de la courroie et ﬁxation du capuchon de retenue de la courroie MONTAGE - 5e OPÉRATION Régler la tension LA POSE ou MORTELLES : POSE – 1re OPÉRATION POSE - 2e OPÉRATION Pose du support de linteau POSE - 3e OPÉRATION Fixation du rail sur le support de linteau POSE - 4e OPÉRATION Positionnement de l'ouvre-porte POSE - 5e OPÉRATION Accrochage de l'ouvre-porte POSE - 6e OPÉRATION Pose de la commande de porte POSE - 7e OPÉRATION Pose des ampoules POSE - 8e OPÉRATION POSE - 9e OPÉRATION Exigences électriques POSE - 10e OPÉRATION Pose du Système Protector® POSE DES SUPPORTS S’assurer que l’ouvre-porteest hors tension Pose murale (Figures 2 et 3) : Pose au sol (Figure 4) : MONTAGE ET CÂBLAGE DES DÉTECTEURS INVERSEURS DU SECURITIÉ Montage : Option A - Installation sans les câbles préinstallés : Option B - Installation pré-câblée : Connexion à l’ouvre-portede garage : DÉPANNAGE DES DÉTECTEURS INVERSEURS DU SÉCURITÉ POSE - 11e OPÉRATION Fixation du Support de Porte PORTES RIGIDES POSE - 12e OPÉRATION Fixation de la biellette au chariot POUR TOUTES LES PORTES RIGIDES 1. Assemblage des biellettes, Figure 5 : IMPORTANT : 2.Méthodes de réglage, Figure 6 : •Réglage de l'ouverture de la porte : diminuer la course d’OUVERTURE RÉGLAGES - 1re OPÉRATION RÉGLAGES - 2e OPÉRATION Réglage de la force RÉGLAGES - 3e OPÉRATION Essai du système d’inversion de sécurité RÉGLAGES - 4e OPÉRATION Essai du Systéme Protector® FONCTIONNEMENT ou DE MORT :