Chamberlain 182665D NOTE:, Wood Doors:, Metal Doors:, ONE-PIECEDOORS

ONE-PIECE DOORS

Please read and comply with the warnings and reinforcement instructions on the previous page. They apply to one-piece doors also.

•Center the door bracket on the top of the door, in line with the header bracket as shown. Mark either the left and right, or the top and bottom holes.

•Metal Doors: Drill 3/16" pilot holes and fasten the bracket with the 1/4"-14x5/8" self-threading screws provided.

•Wood Doors: Drill 5/16" holes and use 5/16"x2" carriage bolts, lock washers and nuts (not provided) or 5/16"x1-1/2" lag screws (not provided) depending on your installation needs.

NOTE: The door bracket may be installed on the top

edge of the door if required for your installation. (Refer to the dotted line optional placement drawing.)

HARDWARE SHOWN ACTUAL SIZE

Self-Threading Screw 1/4"-14x5/8"

Header Wall

2x4 Support

Header

Bracket

Door

Bracket

Optional

Placement of

Door Bracket

Vertical

Centerline of

Garage Door

			Self-Threading
		Door	Screw
		Door	1/4"-14x5/8"
	- Finished Ceiling -	Bracket	Top of Door
			Top of Door
			(Inside Garage)
			(Inside Garage)
			Top Edge
			of Door
			Optional
			Placement
			METAL DOOR
	HORIZONTAL AND VERTICAL		Lock
	REINFORCEMENT IS NEEDED	Nut	Lock
	REINFORCEMENT IS NEEDED		Washer
	FOR LIGHTWEIGHT GARAGE		Washer
	FOR LIGHTWEIGHT GARAGE	5/16"-18	5/16"
	DOORS (FIBERGLASS,	5/16"-18	5/16"
	DOORS (FIBERGLASS,		Top of Door
	ALUMINUM, STEEL, DOORS	Door	Top of Door
	ALUMINUM, STEEL, DOORS	Door	(Inside Garage)
	WITH GLASS PANEL, ETC.).	Bracket	(Inside Garage)
	(NOT PROVIDED)
			Top Edge
			of Door
			Optional
			Placement
			Carriage Bolt
			5/16"x2"
			(Not Provided)
	For a door with no exposed framing,		WOOD DOOR
	For a door with no exposed framing,
	or for the optional installation, use
	lag screws 5/16"x1-1/2" (Not Provided)
	to fasten door bracket.

24

Contents

For Residential Use Only Introduction Assembly Installation Adjustment Operation Preparing Your Garage Door Tools needed Planning Planning (Continued) Carton Inventory Hardware Inventory Assemble the Rail & Install the Trolley Fasten the Rail to the Motor Unit Install the Idler Pulley Install the Belt and Attach the Belt Cap Retainer WARNING Determine the Header Bracket Location Install the Header Bracket Attach the Rail to the Header Bracket Position the Opener Hang the Opener Install the Door Control Install the Lights Attach the Emergency Release Rope and Handle Electrical Requirements Install The Protector System® INSTALLING THE BRACKETS Garage door track installation (preferred): Wall installation (Figures 2 and 3): Floor installation (Figure 4): MOUNTING AND WIRING THE SAFETY REVERSING SENSORS Mounting: Option A - Installation Without Pre-Wiring: Option B - Pre-WiredInstallation: Connect to garage door opener: ALIGNING THE SAFETY REVERSING SENSORS TROUBLESHOOTING THE SAFETY REVERSING SENSORS Fasten the Door Bracket ONE-PIECEDOORS Metal Doors: Connect Door Arm to the Trolley ALL ONE-PIECEDOORS 1. Assemble the door arm, Figure 5: IMPORTANT: 2.Adjustment procedures, Figure 6: •Open door adjustment: decrease UP travel limit Adjust the UP and DOWN Travel Limits Adjust the Force Test the Safety Reversal System Test The Protector System® IMPORTANT SAFETY INSTRUCTIONS Using Your Garage Door Opener Using the Wall-MountedDoor Control To Open the Door Manually CARE OF YOUR OPENER LIMIT AND FORCE ADJUSTMENTS: THE REMOTE CONTROL BATTERY MAINTENANCE SCHEDULE Every Month HAVING A PROBLEM 2.My remotes will not activate the door: 5.My lights will not turn off when door is open: 6.My motor unit hums brieﬂy: Diagnostic Chart To Add or Reprogram a Hand-HeldRemote Control To Erase All Codes From Motor Unit Memory *3-ButtonRemotes To Add, Reprogram or Change a Keyless Entry PIN Rail Assembly Parts Motor Unit Assembly Parts ACCESSORIES 953CD 3-ButtonSECURITY✚® Remote Control: 956CD CHAMBERLAIN® SERVICE IS ON CALL OUR LARGE SERVICE ORGANIZATION SPANS AMERICA AND CANADA INSTALLATION AND SERVICE INFORMATION IS AS Pour Résidences Seulement TABLE DES MATIÈRES Introduction Montage Pose Réglages Préparation de votre porte de garage Outils nécessaires Planiﬁcation Planiﬁcation (Suite) Inventaire de la boîte d’emballage Inventaire des ﬁxations MONTAGE - 1re OPÉRATION Montage du rail et pose du chariot MONTAGE - 2e OPÉRATION Fixation du rail au moteur MONTAGE - 3e OPÉRATION Pose de la poulie MONTAGE - 4e OPÉRATION Pose de la courroie et ﬁxation du capuchon de retenue de la courroie MONTAGE - 5e OPÉRATION Régler la tension LA POSE ou MORTELLES : POSE – 1re OPÉRATION POSE - 2e OPÉRATION Pose du support de linteau POSE - 3e OPÉRATION Fixation du rail sur le support de linteau POSE - 4e OPÉRATION Positionnement de l'ouvre-porte POSE - 5e OPÉRATION Accrochage de l'ouvre-porte POSE - 6e OPÉRATION Pose de la commande de porte POSE - 7e OPÉRATION Pose des ampoules POSE - 8e OPÉRATION POSE - 9e OPÉRATION Exigences électriques POSE - 10e OPÉRATION Pose du Système Protector® POSE DES SUPPORTS S’assurer que l’ouvre-porteest hors tension Pose murale (Figures 2 et 3) : Pose au sol (Figure 4) : MONTAGE ET CÂBLAGE DES DÉTECTEURS INVERSEURS DU SECURITIÉ Montage : Option A - Installation sans les câbles préinstallés : Option B - Installation pré-câblée : Connexion à l’ouvre-portede garage : DÉPANNAGE DES DÉTECTEURS INVERSEURS DU SÉCURITÉ POSE - 11e OPÉRATION Fixation du Support de Porte PORTES RIGIDES POSE - 12e OPÉRATION Fixation de la biellette au chariot POUR TOUTES LES PORTES RIGIDES 1. Assemblage des biellettes, Figure 5 : IMPORTANT : 2.Méthodes de réglage, Figure 6 : •Réglage de l'ouverture de la porte : diminuer la course d’OUVERTURE RÉGLAGES - 1re OPÉRATION RÉGLAGES - 2e OPÉRATION Réglage de la force RÉGLAGES - 3e OPÉRATION Essai du système d’inversion de sécurité RÉGLAGES - 4e OPÉRATION Essai du Systéme Protector® FONCTIONNEMENT ou DE MORT :