The units can be wired to any Analog Trunk in an internal home phone system.
NOTE: Installation where fiber optic phone lines are present may require additional modifications from your telephone provider. Contact your provider for more information.
Single Unit
Telco Entrance Box Demarcation Point
Ring
Tip
Internal
Phone System
Analog
Trunk
2 |
| |
1 EX | Tip | |
EX | ||
T | ||
3Analog | ||
R | ||
| Ring | |
4 EX |
|
Use
Board Output IO
RES
J6
Ring TELCO
Tip J8
| NO |
| LED 4 |
J5 | NC |
| C |
| RELAY 4 |
| NO |
J4 | NC |
| LED 3 |
| C |
| RELAY 3 |
| NO |
J3 | NC |
| C |
| LED 2 |
| NO |
| RELAY 2 |
| NC |
J1 | C |
|
Never run Telco wires and High Voltage wires in the same conduit. The high voltage wires may interfere with the Telco wires, possibly causing the system to malfunction.
LED 1 |
RELAY 1 |
Internal an
Multiple Units (Up to 7)
IMPORTANT: You must program the unit
ID's for each unit wired in the series. See Keypad Programming Manual.
Ring
Tip
Telco Entrance Box
Demarcation Point
Internal
Phone System
To next unit (Unit ID 5 then 4 etc.) (Unit ID 1 is farthest away
from Telco Box)
Use
2 |
| |
1 EX | Tip | |
EX | ||
T | ||
3Analog | ||
R | ||
| Ring | |
4 EX |
|
Analog
Trunk
|
| IO |
|
|
|
| Output |
| NO |
|
|
|
| LED 4 |
|
| Board | J5 | NC |
|
|
| RELAY 4 | |
|
|
|
| C |
Ring | RES |
|
| NO |
|
|
| J4 | NC |
Tip |
|
|
| LED 3 |
|
|
| C | |
J6 |
|
| RELAY 3 | |
|
|
|
| |
|
|
|
| NO |
Ring | TELCO |
| J3 | NC |
|
|
|
| C |
|
|
|
| LED 2 |
Tip |
|
|
| NO |
J8 |
|
| RELAY 2 | |
|
|
|
| NC |
Unit ID 6 |
| J1 | C | |
|
| |||
Output Board |
|
| LED 1 | |
(See page 6) |
|
| RELAY 1 | |
|
| IO |
|
|
|
| Output |
| NO |
|
|
|
| LED 4 |
|
| Board | J5 | NC |
|
|
| RELAY 4 | |
|
|
|
| C |
Ring | RES |
|
| NO |
|
|
| J4 | NC |
Tip |
|
|
| LED 3 |
|
|
| C | |
J6 |
|
| RELAY 3 | |
|
|
|
| |
|
|
|
| NO |
Ring | TELCO |
| J3 | NC |
|
|
|
| C |
|
|
|
| LED 2 |
Tip |
|
|
| NO |
J8 |
|
| RELAY 2 | |
|
|
|
| NC |
Unit ID 7 |
| J1 | C | |
|
| |||
Output Board |
|
| LED 1 | |
(See page 6) |
|
| RELAY 1 |
Page 13