Even if you plan to program the gate operator by telephone, you may want to enter some immediate instructions during installation. The following list of instructions will help you set basic controls so the gate will operate properly until you have time for full programming, either directly or by telephone. For complete programming instructions, refer to ÒSL 1000, SW 2000, and BG
To access programming mode: enter ✱✱✱ 000000 (3 asterisks, 6 zeroes)
To program a command: a) enter step number b) enter required data c) enter # (pound sign)
To exit programming mode: enter 00# (2 zeroes, 1 pound sign)
| Step | Purpose | Step | Default |
| Acceptable Input |
|
|
|
|
|
|
|
|
|
01 | Gate Type | 1 | 1 | 0 | = Slide, 1 = Swing, 2 = Barrier, | ||
|
|
|
|
| 3 | = Linear | |
02 | Operator Type | 1 | 0 | 0 | = Single, 1 = Master, 2 = Slave | ||
03 | Pair Type | 1 | 0 | 0=Bipart, 1=Latch, 2=Not Used, | |||
|
|
|
|
| 3=Tandem | ||
04 | Not Used | - | - | - |
|
| |
05 | Not Used | - | - |
|
|
| |
06 | 1 | 0 | 0 = Disabled, 1 = Enabled | ||||
07 | Latch Delay Time | 3 | 6 | 0 | Ð 250 Seconds (.4 sec. | ||
|
|
|
|
| Increments) | ||
08 | Reclose Time (RT) | Up to 3 | 30 | 0 Ð 250 Seconds (0 = Disabled) | |||
09 | Not Used | - | - | - |
|
| |
10 | Not Used | - | - | - |
|
| |
11 | Obstruction Sense Backup Closing | Up to 3 | 12 | 12 Ð 499 Inches See note below.¥ | |||
12 | Obstruction Sense Backup Opening | Up to 3 | 12 | 12 Ð 499 Inches See note below.¥ | |||
13 | Interrupt Bar Backup If Closing | Up to 3 | 12 | 12 Ð 499 Inches See note below.¥ | |||
14 | Interrupt Bar Backup If Opening | Up to 3 | 12 | 12 Ð 499 Inches See note below.¥ | |||
15 | Return to Factory Set Defaults | 6 | N/A | 101010 (partial), 191919 (full) |
Slide gates move at about one foot per second, so backup distances (Obstruction Senses and Interrupt Bar Backup) are easy to enter. To move the gate one foot, you enter 12 inches.
Swing gates, however, move in degrees per second, so it is the length of the gate that determines how far the gate moves each second. For instance, a twenty foot gate will move twice as far as a ten foot gate in the same amount of time. As a result, entering backup distances for swing gates is different than for slide gates. Use the following table to enter swing gate backup distances:
I want my gate to move |
| And my gate length is: |
| |
this far out at the end: | 10' | 15' |
| 20' |
One foot | Enter 9" | Enter 6" |
| Enter 3" |
Two feet | Enter 18" | Enter 12" |
| Enter 6" |
Three feet | Enter 27" | Enter 18" |
| Enter 9" |
Rev F | Doc | 17 of 42 |