Manuals / Brands / Baby / Safety Gate / Chamberlain / Baby / Safety Gate

Chamberlain SW 2000-X3 NOTE:, CONNECTORS, ADJUSTMENTS

1 48

Download 48 pages, 4.57 Mb

ADJUSTMENTS

OBSTRUCTION	Adjustable pot controls gate sensitivity to blockages by the
RIGHT (R69)	instantaneous rise in motor current. When the limit is exceeded, the
	gate stops and reverses a programmed distance (a minimum of 2
	inches).
OBSTRUCTION	Adjustable pot controls gate sensitivity to blockages by the
LEFT (R160)	instantaneous rise in motor current. When the limit is exceeded, the
	gate stops and reverses a programmed distance (a minimum of 2
	inches).

NOTE: LiftMaster gate operators have two obstruction sense adjustments (left and right) where other gate operators have only one. This allows greater flexibility of installation. For instance, you can install a gate on an incline and not worry about sacrificing downhill gate sensitivity.

INRUSH	Adjustable pot controls the delay in sensitivity to gate
(R203)	obstructions. This delay in sensitivity prevents the initial motor
	inrush current from causing a obstruction fault. The weight of the
	gate determines this setting.

CONNECTORS
LIMIT SWITCH (J4)	Connector for the left/right limit switch cable.
PWR INPUT (J1)	Connector for AC input power.
MOTOR POWER (J3)	Connector for the motor cable.
LOOP DETECTOR	Connector for the optional LiftMaster Outside Interrupt Loop
	detector
(J15)	add-on board.
LOOP DETECTOR	Connector for the optional LiftMaster Inside Interrupt Loop detector
(J12)	add-on board.
LOOP DETECTOR	Connector for optional LiftMaster Shadow Loop detector add-on
(J13)	board.
LOOP DETECTOR	Connector for optional LiftMaster Exit Loop detector add-on board.
(J14)
OBSTRUCTION	Connector for factory-installed alarm.
ALARM

37 of 42

Doc 01-20099

Rev F

Contents

ESTATE SERIES MODEL SW 3 YEAR WARRANTY Page TABLE OF CONTENTS TABLE OF FIGURES DIMENSIONS WEIGHT ELECTRICAL Page SAFETY SUMMARY WARNING BASIC INSTALLATION HINTS AND RULES PART SITE PREPARATION NOTES B.PAD AND MOUNT Figure 2. Pad and Mount C.POWER WIRING D.LOOP DETECTORS AND PHOTO-SENSORS E.TELEPHONE CONNECTION F. MASTER/SLAVE INTERCONNECTION (MASTER/SLAVE SYSTEM ONLY) G.OTHER CONNECTIONS SYSTEM INSTALLATION To avoid injury, always turn off the unit power switch before working on gate D. RUNNING INPUT WIRING WARNING E.SETTING GATE OPEN DIRECTION SWITCHES S2 AND S3 Figure 5. Gate Direction and UPS Low Battery Switch Locations F. POWER UP PROCEDURE CAUTION NOTE G. USING MANUAL CONTROLS Figure 6. Manual Controls, Location and Use H. GATE ARM INSTALLATION NOTES: with gate stop on driveway side Figure 7. Gate Arm Installation I.SETTING LIMIT CAMS 1. SETTING RIGHT GATE LIMIT CAMS Figure 8. Setting Right Gate Limit Cam 2. SETTING LEFT GATE LIMIT CAMS Figure 9. Setting Left Gate Limit Cam J. GATE SENSITIVITY ADJUSTMENTS Figure 10. Gate Sensitivity Adjustments Location "OPEN TO RIGHT" ADJUSTMENT PROCEDURES Right Gate Motion Adjustment (R69) Left Gate Motion Adjustment (R160) "OPEN TO LEFT" ADJUSTMENT PROCEDURES INRUSH CURRENT ADJUSTMENT (R203) K. CONNECTING INPUT WIRING Figure 11. Control Board Wiring IMPORTANT: Bi-part Latch: L. BASIC GATE OPERATOR PROGRAMMING To access To program To exit Step M.POST INSTALLATION PROCEDURES 1.Setup main power switch S2 unit power 6. Alternate Action Note: 7. Reclose Timer 8. Interrupt Loop and Anti-Tailgating(ATG) When Exiting Inside Interrupt Loop: Figure 12. Photo-SensorCoverage Areas 10. Photo-Sensors(Secondary Obstruction Sensing per UL 325 Requirements) (Inside-Open Coverage): Coverage Area B 11. Interrupt Bar (Edge Sensor) 12. Maglock N. FINAL ASSEMBLY OF GATE OPERATOR Figure 13. Gate Operator Final Assembly IMPORTANT SAFETY PROCEDURE Turn off power to the gate operator at the circuit breaker and wait for one minute Page LIFTMASTER LOOP DETECTOR BOARDS (OPTIONAL) TROUBLESHOOTING AND MAINTENANCE 4. THE CONTROL BOARD RESETS RIGHT AFTER GATE STARTS MOVING 5. GATE STOPS AND REVERSES IMMEDIATELY AFTER IT STARTS Mostly in cold weather or mornings: 6. GATE STOPS A FEW SECONDS AFTER IT STARTS 7. GATE SUDDENLY REVERSES WHILE MOVING 13. GATE DOES NOT CLOSE AUTOMATICALLY 14. ALTERNATE ACTION DOES NOT WORK 15. GATE DOES NOT OPEN TO THE CORRECT DIRECTION 16. THERE IS SLACK OR PLAY IN THE GATE 17. ATG (ANTI-TAILGATE)DOES NOT WORK Units are not synchronized: One gate braking to stop causes a fault in the other (moving) gate: B. FAULT LIST The following conditions can cause a fault: Instantaneous motor overcurrent C.FAULTS AND THEIR CAUSES 1.IF OBSTRUCTION LED IS ON 2.IF INTERRUPT BAR LED IS TURNED ON 3.IF OPEN MTR LED IS TURNED ON 4.IF STUCK-LIMITLED IS TURNED ON D. MAINTENANCE To avoid injury, always turn off the unit power switch before working on gate PREVENTIVE MAINTENANCE TASKS Gate Arm: Gate: PREVENTIVE MAINTENANCE INSTRUCTIONS MAINTENANCE SCHEDULE TABLE APPENDIX A SYSTEM OPERATION REFERENCE FUNCTIONAL INPUTS MANUAL INPUTS: OPEN, CLOSE, AND STOP (TB2) Continuous activation holds gate open closed INSIDE/OUTSIDE INTERRUPT LOOP DETECTOR (TB16) SWING LINEAR SLIDE BARRIER RADIO INPUT (TB6) OBSTRUCTION ALARM (TB17) LOW BATTERY/ NO AC POWER (TB18) 24VAC OUTPUT (TB7) MAGLOCK INPUT (TB4) ADJUSTMENTS CONNECTORS APPENDIX B: SW 2000-X3PARTS LIST Bold = Assembly ¥ = Assembly Part Page GLOSSARY FCC REQUIREMENTS NOTICE TO CANADIAN USERS NOTICE: Caution: Ringer Equivalence Number