Manuals / Cisco Systems / Computer Equipment / Network Router

Cisco Systems 1140 specifications Assigning an IP Address Using the CLI, interface bvi1

Models: 1140

1 36

Download 36 pages 45.88 Kb

Page 8

interface bvi1

	Command	Purpose

Step 2	interface bvi1	Enters interface configuration mode for the
		BVI.

Step 3	ip address ip_address net_mask	Assigns an IP address and subnet mask
		address to the BVI.

Assigning an IP Address Using the CLI

Follow these steps to access the CLI using a Telnet session. These steps are for a PC running Microsoft Windows with a Telnet terminal application. Check your PC operating instructions for detailed instructions.

Step 1 Select Start > Programs > Accessories > Telnet.

If Telnet is not listed in your Accessories menu, select Start > Run, type Telnet in the entry field, and press Enter.

Step 2 When the Telnet window appears, click Connect and select Remote System. Step 3 In the Host Name field, type the access point IP address and click Connect.

Note If you are connected to the access point using a Telnet session, you lose your connection to the access point when you assign a new IP address to the BVI. If you need to continue configuring the access point using Telnet, use the new IP address to open another Telnet session to the access point.

8

Image 8

Cisco Systems 1140 specifications Assigning an IP Address Using the CLI, interface bvi1, ip address ipaddress netmask

Contents

1 About this Guide 2 Safety Instructions 3 Overview 4 Obtaining and Assigning an IP Address 5 Mounting the Access Point6 Configuring Basic Settings 7 Troubleshooting 8 Access Point SpecificationsSAVE THESE INSTRUCTIONS 2 Safety Instructions1 About this Guide 20A. Statement 3 Overview Verifying Shipped ComponentsKey Ports and Components 4 Obtaining and Assigning an IP Address Performing a Site SurveyConnecting to the Access Point Locally Step 1 configure terminalEnter global configuration mode Assigning the IP Address to the BVIAssigning an IP Address Using the CLI Step 1 Select Start Programs Accessories Telnetinterface bvi1 ip address ipaddress netmask5 Mounting the Access Point 6 Configuring Basic SettingsPage Step 5 Configure the settings using the following sections as a guide DHCP-IP address is automatically assigned by the network DHCP serverConfiguring the Radios Default Default Settings on the Express Setup PageSetting Step 5 Click Apply Configuring Security SettingsEnabling the Radio Interfaces Using VLANs Configuring Basic Security SettingsUnderstanding Express Security Settings Express Security Limitations Configuring Security for 802.11nExpress Security Types Using the Express Security Page 7 Troubleshooting Checking the Access Point LEDAccess Point LED Diagnostic Messages Message TypeStatus LED Message MeaningConfiguring System Power Settings Access Point LED Diagnostic Messages continuedPower Source System Power SettingsSwitch Status Figure 4 Low Power Mode WarningFinding More Troubleshooting Help System Power Settings continuedCategory 8 Access Point SpecificationsSpecification 10 Declarations of Conformity and Regulatory Information 9 Obtaining Documentation and Submitting a Service Requestrefer to Channels and Maximum Power Settings for Cisco Aironet Tested To Comply With FCC Standards FOR HOME OR OFFICE USE ModelsVCCI Statement for Japan Guidelines for Operating Cisco Aironet Access Points in Japan Japanese TranslationEnglish Translation 03-6434-6500Statement 371-Power Cable and AC Adapter Industry CanadaCanadian Compliance Statement English TranslationEuropean Community, Switzerland, Norway, Iceland, and Liechtenstein Page Page Administrative Rules for Cisco Aironet Access Points in Taiwan Declaration of Conformity for RF ExposureUnited States CanadaChinese Translation English Translation Chinese Translation Operation of Cisco Aironet Access Points in BrazilAccess Point Models Regulatory Information Portuguese TranslationEnglish Translation Figure 5 Brazil Regulatory InformationAmericas Headquarters Asia Pacific HeadquartersEurope Headquarters Cisco Systems, Inc