Manuals / Cisco Systems / Lawn and Garden / Weather Radio

Cisco Systems 1500 Series Access Point Mounting Orientations, Roof-Overhang Installation, page

Models: 1500 Series

1 24

Download 24 pages 1.5 Kb

Page 12

•Access Point Mounting Orientations, page 2-12

Chapter 2 Mounting Instructions

Mounting the Access Point

C i s c o C o n f i d e n t i a l - D r a ft 1

Article 800, which includes requirements for a Listed primary protector upon entering the building, and limits the installation to only Listed networking equipment designed to accommodate telecommunication interfaces.

Caution To provide inline PoE, you must use the power injector (AIR- PWRINJ1500=) specified for the access point. Other power injectors, PoE switches, and 802.3af power sources may not provide adequate power, which may cause the access point to malfunction and cause over-current conditions at the power source. You must ensure that the switch port connected to the access point has PoE turned off.

Refer to these sections for installation details.

•Access Point Mounting Orientations, page 2-12

•Mounting the Access Point on a Vertical or Horizontal Surface, page 2-15

•Roof-Overhang Installation, page 2-16

•Mounting the Access Point on a Pole, page 2-17

•Streetlight Pole Installations, page 2-21

Access Point Mounting Orientations

When installing an access point on a horizontal or vertical surface, you must ensure that the access point is correctly oriented.

Caution When mounting the access point in a horizontal position, you must position the side with the 2.4-GHz antenna connector facing down (see Figure 2-4). When you are mounting the access point in a vertical position, you must position the access point with the 5-GHz antenna connector facing up (see Figure 2-5). This positioning is required to prevent water intrusion into the unit from the vent. You must ensure that the vent is not obstructed by anything.

Cisco Aironet 1500 Series Outdoor Mesh Access Point Hardware Installation Guide

2-12	OL-9977-05

Image 12

Cisco Systems 1500 Series manual Access Point Mounting Orientations, page, Roof-Overhang Installation, page, 2-12

Contents

Unpacking the Access Point, page Tools and Materials, page Warnings, page Safety Information, page Installation Guidelines, pageMounting the Access Point, page C i s c o C o n f i d e n t i a l - D r a ftUnpacking the Access Point Package ContentsTools and Materials C i s c o C o n f i d e n t i a l - D r a ftSafety Information WarningsSAVE THESE INSTRUCTIONS C i s c o C o n f i d e n t i a l - D r a ftFCC Safety Compliance Statement Safety PrecautionsC i s c o C o n f i d e n t i a l - D r a ft Avoiding Damage to Radios in a Testing Environment C i s c o C o n f i d e n t i a l - D r a ftInstallation Guidelines Site SurveysC i s c o C o n f i d e n t i a l - D r a ft Before Beginning the Installation Becoming Familiar with Access Point Installation ComponentsC i s c o C o n f i d e n t i a l - D r a ft C i s c o C o n f i d e n t i a l - D r a ft Building roof-overhangC i s c o C o n f i d e n t i a l - D r a ft 5.8-GHz antenna bracket LAP1510 modelAdding the Access Point MAC Addresses to the Controller Filter List Enabling Zero Touch Configuration on the ControllerStep 2 Choose WIRELESS MESH Step 3 Check Enable Zero Touch ConfigurationMounting the Access Point Configuring a RAPInstallation Options 2-11Access Point Mounting Orientations Access Point Mounting Orientations, pageMounting the Access Point on a Vertical or Horizontal Surface, page Roof-Overhang Installation, page2-13 Chapter 2 Mounting Instructions Mounting the Access PointC i s c o C o n f i d e n t i a l - D r a ft Figure 2-4 Preferred Horizontal Orientation2-14 Figure 2-5 illustrates the access point vertical orientationC i s c o C o n f i d e n t i a l - D r a ft Mounting the Access Point on a Vertical or Horizontal Surface 2-15C i s c o C o n f i d e n t i a l - D r a ft Roof-Overhang Installation Step 7 Continue with the “Roof-Overhang Installation” section2-16 C i s c o C o n f i d e n t i a l - D r a ftMounting the Access Point on a Pole Step 7 Continue with the “Grounding the Access Point” section on page2-17 C i s c o C o n f i d e n t i a l - D r a ft2-18 Figure 2-8 Adjustment Plate Attached to the Mounting PlateC i s c o C o n f i d e n t i a l - D r a ft 2-19 Figure 2-9 Pole Clamp and Clamp Adjustment Plate Mounted on a PoleC i s c o C o n f i d e n t i a l - D r a ft 2-20 Step 7 Continue with the “Grounding the Access Point” section on pageFigure 2-10 Access Point Attached to the Pole Clamp C i s c o C o n f i d e n t i a l - D r a ftGrounding the Access Point Streetlight Pole Installations2-21 C i s c o C o n f i d e n t i a l - D r a ft2-22 C i s c o C o n f i d e n t i a l - D r a ft2-23 Figure 2-11 Using the Streetlight Power Tap AdapterC i s c o C o n f i d e n t i a l - D r a ft What to Do Next 2-24C i s c o C o n f i d e n t i a l - D r a ft