Manuals / Cisco Systems / Lawn and Garden / Weather Radio

Cisco Systems 1500 Series manual 2-23, C i s c o C o n f i d e n t i a l - D r a ft

Models: 1500 Series

1 24

Download 24 pages 1.5 Kb

Page 23

Figure 2-11 Using the Streetlight Power Tap Adapter

Chapter 2 Mounting Instructions

Mounting the Access Point

C i s c o C o n f i d e n t i a l - D r a ft 1

Step 7 Connect the streetlight power tap adapter to the access point AC power connector, as shown in Figure 2-11.

Note Hand-tighten the cable connector until it locks. No specific torque is required.

Step 8 Plug the streetlight power tap adapter into the outdoor light control fixture, as shown in Figure 2-11.

Figure 2-11 Using the Streetlight Power Tap Adapter

1 2

3

1

2

	142680
Outdoor light control		3		10-AWG copper grounding wire
Outdoor light control		3		10-AWG copper grounding wire
Streetlight power tap adapter

Step 9 Plug the outdoor light control into the streetlight power tap adapter.

Step 10 Ensure the antennas are connected to the access point before you apply power to the access point. Step 11 Turn on the power to the outdoor light control fixture at the designated circuits.

Note When you power up a MAP that is not connected to a wired Ethernet network to the controller, the access point uses the Cisco Adaptive Wireless Path Protocol to bind to another MAP with the best path to a RAP connected to the wired network to a controller.

The access point sends a discovery request when powered up. If you have configured the access point in the controller correctly, the controller sends back a discovery response to the access point. When that happens, the access point sends out a join request to the controller and the controller responds with a join confirmation response. Then, the access point establishes an LWAPP connection to the controller and gets the shared secret configured on the controller under zero-touch configuration.

Cisco Aironet 1500 Series Outdoor Mesh Access Point Hardware Installation Guide

	OL-9977-05	2-23

Image 23

Cisco Systems 1500 Series 2-23, C i s c o C o n f i d e n t i a l - D r a ft, 11 Using the Streetlight Power Tap Adapter

Contents

C i s c o C o n f i d e n t i a l - D r a ft Unpacking the Access Point, page Tools and Materials, pageWarnings, page Safety Information, page Installation Guidelines, page Mounting the Access Point, pageC i s c o C o n f i d e n t i a l - D r a ft Unpacking the Access PointPackage Contents Tools and MaterialsC i s c o C o n f i d e n t i a l - D r a ft Safety InformationWarnings SAVE THESE INSTRUCTIONSC i s c o C o n f i d e n t i a l - D r a ft FCC Safety Compliance StatementSafety Precautions C i s c o C o n f i d e n t i a l - D r a ft Avoiding Damage to Radios in a Testing EnvironmentC i s c o C o n f i d e n t i a l - D r a ft Installation GuidelinesSite Surveys C i s c o C o n f i d e n t i a l - D r a ft Before Beginning the InstallationBecoming Familiar with Access Point Installation Components Building roof-overhang C i s c o C o n f i d e n t i a l - D r a ft5.8-GHz antenna bracket LAP1510 model C i s c o C o n f i d e n t i a l - D r a ftStep 3 Check Enable Zero Touch Configuration Adding the Access Point MAC Addresses to the Controller Filter ListEnabling Zero Touch Configuration on the Controller Step 2 Choose WIRELESS MESH2-11 Mounting the Access PointConfiguring a RAP Installation OptionsRoof-Overhang Installation, page Access Point Mounting OrientationsAccess Point Mounting Orientations, page Mounting the Access Point on a Vertical or Horizontal Surface, pageFigure 2-4 Preferred Horizontal Orientation 2-13Chapter 2 Mounting Instructions Mounting the Access Point C i s c o C o n f i d e n t i a l - D r a ftC i s c o C o n f i d e n t i a l - D r a ft 2-14Figure 2-5 illustrates the access point vertical orientation C i s c o C o n f i d e n t i a l - D r a ft Mounting the Access Point on a Vertical or Horizontal Surface2-15 C i s c o C o n f i d e n t i a l - D r a ft Roof-Overhang InstallationStep 7 Continue with the “Roof-Overhang Installation” section 2-16C i s c o C o n f i d e n t i a l - D r a ft Mounting the Access Point on a PoleStep 7 Continue with the “Grounding the Access Point” section on page 2-17C i s c o C o n f i d e n t i a l - D r a ft 2-18Figure 2-8 Adjustment Plate Attached to the Mounting Plate C i s c o C o n f i d e n t i a l - D r a ft 2-19Figure 2-9 Pole Clamp and Clamp Adjustment Plate Mounted on a Pole C i s c o C o n f i d e n t i a l - D r a ft 2-20Step 7 Continue with the “Grounding the Access Point” section on page Figure 2-10 Access Point Attached to the Pole ClampC i s c o C o n f i d e n t i a l - D r a ft Grounding the Access PointStreetlight Pole Installations 2-21C i s c o C o n f i d e n t i a l - D r a ft 2-22C i s c o C o n f i d e n t i a l - D r a ft 2-23Figure 2-11 Using the Streetlight Power Tap Adapter C i s c o C o n f i d e n t i a l - D r a ft What to Do Next2-24