Manuals / Cisco Systems / Computer Equipment / Network Card

Cisco Systems AS5400 manual Online Insertion and Removal OIR of DFCs

Models: AS5400

1 88

Download 88 pages 63.81 Kb

Page 20

Online Insertion and Removal (OIR) of DFCs

Chapter 2 Dial Feature Card and Carrier Card Guidelines

Online Insertion and Removal (OIR) of DFCs

•Universal access (analog modem or digital calls) is supported when an interface is configured for ISDN PRI signaling. PRI signaling is available for both T1 and E1 trunks.

In any single DFC slot, you can install your choice of:

•One T1, E1, or T3 dial feature card

•One universal port card

Online Insertion and Removal (OIR) of DFCs

All DFCs on the Cisco AS5350 and Cisco AS5400 chassis support online insertion and removal (also known as hot swapping). You can install, remove, replace, and rearrange the DFCs without turning off the chassis power.

When the chassis detects that a DFC is installed or removed, it automatically runs diagnostic and discovery routines, acknowledges the presence or absence of the DFC, and resumes chassis operation without any operator intervention.

See:

•Chapter 3, “T1 and E1 Dial Feature Cards,” to perform OIR of the T1 or E1 DFC.

•Chapter 4, “T3 Dial Feature Card,” to perform OIR of the T3 DFC.

•Chapter 5, “Universal Port Dial Feature Card,” to perform OIR of the universal port DFC.

Removing and Installing Populated Carrier Cards

Caution The carrier cards that carry the DFCs are not hot swappable. Removing a card while the system is still powered on may cause permanent damage to electronic circuits on the card.

The DFC carrier card plugs into one of the backplane slots and supports two DFCs. The carrier card increases backplane capacity and allows OIR of the DFCs. (See Figure 2-1.)

Figure 2-1 Carrier Card With Two 8 PRI CT1 Cards

29032

Warning Before working on a chassis or working near power supplies, unplug the power cord on AC units; disconnect the power at the circuit breaker on DC units. To see translations of the warnings that appear in this publication, refer to the Regulatory Compliance and Safety Information document that accompanied this device.

Cisco AS5350 and Cisco AS5400 Universal Gateway Card Installation Guide

2-2	78-13311-01

Image 20

Cisco Systems AS5400 manual Online Insertion and Removal OIR of DFCs, Removing and Installing Populated Carrier Cards

Contents

Corporate Headquarters Installation GuideCisco AS5350 and Cisco AS5400 Universal Gateway Card Cisco Systems, Inc 170 West Tasman Drive San Jose, CATurn the television or radio antenna until the interference stops Cisco AS5350 and Cisco AS5400 Universal Gateway CardCopyright 2001, Cisco Systems, Inc All rights reservedSafety Warnings, Recommendations, and Tools Required Online Installation and Removal of the T1 or E1 DFCWhere to Go Next PrefaceConfiguration TroubleshootingVerification OverviewCabling Specifications ContentsGetting Help Attaching the 8-Port Interface Cable to a Bracket Optional A-5Contents 78-13311-01Related Documentation, page New Hardware Features, page Safety WarningsDial Feature Card and T1 and E1 Dial FeatureTroubleshooting Cabling SpecificationsDocument Conventions ConventionWaarschuwing Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel kan veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij elektrische schakelingen betrokken risicos en dient u op de hoogte te zijn van standaard maatregelen om ongelukken te voorkomen. Voor vertalingen van de waarschuwingen die in deze publicatie verschijnen, kunt u het document Regulatory Compliance and Safety Information Informatie over naleving van veiligheids- en andere voorschriften raadplegen dat bij dit toestel is ingesloten Page Obtaining Documentation World Wide WebDocumentation CD-ROM Ordering DocumentationContacting TAC by Using the Cisco TAC Website Obtaining Technical AssistanceCisco.com Technical Assistance CenterNew Hardware Features Related DocumentationContacting TAC by Telephone xiiiPreface New Hardware Features 78-13311-01Safety Warnings, Recommendations, and Tools Required General SafetyGeneral Safety, page Maintaining Safety with Electricity, page Required Tools and Equipment, page Where to Go Next, pageMaintaining Safety with Electricity Preventing Electrostatic Discharge Required Tools and EquipmentWhere to Go Next Chapter 2, “Dial Feature Card and Carrier Card Guidelines”Chapter 3, “T1 and E1 Dial Feature Cards” Chapter 4, “T3 Dial Feature Card”Dial Feature Card and Carrier Card Guidelines Removing and Installing Populated Carrier Cards, pageGetting Help, page Where to Go Next, page Dial Feature CardsOnline Insertion and Removal OIR of DFCs Removing and Installing Populated Carrier CardsChapter 4, “T3 Dial Feature Card,” to perform OIR of the T3 DFC To remove a populated carrier card, follow the steps below Removing a Populated Carrier CardStep 1 Power off the chassis Figure 2-3 Loosen the Captive Screws on the Cisco AS5400 Figure 2-4 Removing the Carrier Card from the Cisco AS5350Figure 2-5 Removing the Carrier Card from the Cisco AS5400 cardInstalling a Populated Carrier Card Step 6 Reconnect all interface cables Chapter 3, “T1 and E1 Dial Feature Cards.” Chapter 4, “T3 Dial Feature Card.”Chapter 5, “Universal Port Dial Feature Card.” Chapter 6, “Troubleshooting.” Appendix A, “Cabling Specifications.”78-13311-01 Chapter 2 Dial Feature Card and Carrier Card GuidelinesWhere to Go Next T1 and E1 Dial Feature Cards Online Installation and Removal of the T1 or E1 DFC, pageConfiguring Input Impedance for the E1 DFC, page Getting Help, page Where to Go Next, pageSpecification SpecificationTable 3-1 T1 DFC Network Specifications Table 3-2 E1 DFC Network SpecificationsRemoving the T1 or E1 DFC Online Installation and Removal of the T1 or E1 DFCOverview Note The clear port command only applies to the universal port DFC Router# busyout slot-numberRouter# clear port slot-number/port number Rx Tx Figure 3-6 Loosen the Captive Screws on the Cisco AS5350Figure 3-7 Loosen the Captive Screws on the Cisco AS5400 Figure 3-10 Blank DFC Cover Figure 3-8 Remove the DFC from the Cisco AS5350Figure 3-9 Remove the DFC from the Cisco AS5400 Chapter 3 T1 and E1 Dial Feature Cards Online Installation and Removal of the T1 or E1 DFCRouter# show controller e1 6/0 timeslot Router# show busyoutChapter 3 T1 and E1 Dial Feature Cards Online Installation and Removal of the T1 or E1 DFCRouter# show busyout show chassis slotInstalling the T1 or E1 DFC 3-10 Figure 3-12 Install the T1 or E1 DFC in the Cisco AS5400Figure 3-13 Tighten the Captive Screws on the Cisco AS5350 Figure 3-14 Tighten the Captive Screws on the Cisco AS5400Configuring Input Impedance for the E1 DFC ConfigurationCommand Verification3-12 Chapter 3 T1 and E1 Dial Feature CardsConfiguring Input Impedance for the E1 DFC service udp-small-servers service tcp-small-serversConfiguring Input Impedance for the E1 DFC 3-13Chapter 3 T1 and E1 Dial Feature Cards 3-14 Where to Go NextChapter 4, “T3 Dial Feature Card.” Chapter 5, “Universal Port Dial Feature Card.”T3 Dial Feature Card Online Installation and Removal OIR of the T3 DFC, pageGetting Help, page Where to Go Next, page OverviewOnline Installation and Removal OIR of the T3 DFC Removing the T3 DFCOverview Figure 4-2 Slot Numbering on the Cisco AS5350 ChassisFigure 4-3 Slot Numbering on the Cisco AS5400 Chassis Router# busyout slot-numberRouter# clear port slot-number/port number Figure 4-4 Loosen the Captive Screws on the Cisco AS5350 Figure 4-5 Loosen the Captive Screws on the Cisco AS5400Installing the T3 DFC Figure 4-6 Remove the DFC from the Cisco AS5350Figure 4-7 Remove the DFC from the Cisco AS5400 Figure 4-8 Blank DFC CoverFigure 4-11 Tighten the Captive Screws on the Cisco AS5350 Figure 4-9 Install the T3 DFC in the Cisco AS5350Figure 4-10 Install the T3 DFC in the Cisco AS5400 Where to Go Next Chapter 5, “Universal Port Dial Feature Card.”Chapter 6, “Troubleshooting.” Appendix A, “Cabling Specifications.” Getting HelpChapter 4 T3 Dial Feature Card Where to Go Next 78-13311-01Universal Port Dial Feature Card SPE Firmware, page Getting Help, page Where to Go Next, pageOnline Insertion and Removal OIR of the Universal Port DFC, page OverviewOnline Insertion and Removal OIR of the Universal Port DFC Removing the Universal Port DFCOverview Figure 5-2 Slot Numbering on the Cisco AS5350 ChassisFigure 5-3 Slot Numbering on the Cisco AS5400 Chassis Router# busyout slot-numberRouter# clear port slot-number/port number Figure 5-6 Remove the DFC from the Cisco AS5350 Figure 5-4 Loosen the Captive Screws on the Cisco AS5350Figure 5-5 Loosen the Captive Screws on the Cisco AS5400 Chapter 5 Universal Port Dial Feature Card Figure 5-7 Remove the DFC from the Cisco AS5400Figure 5-8 Blank DFC Cover Online Insertion and Removal OIR of the Universal Port DFCChapter 5 Universal Port Dial Feature Card Online Insertion and Removal OIR of the Universal Port DFCRouter# clear port Router# show busyoutFigure 5-10 Install the Universal Port DFC in the Cisco AS5400 Installing the Universal Port DFCFigure 5-9 Install the Universal Port DFC in the Cisco AS5350 Figure 5-11 Tighten the Captive Screws on the Cisco AS5350 Figure 5-12 Tighten the Captive Screws on the Cisco AS5400SPE Firmware Where to Go NextChapter 6, “Troubleshooting.” Appendix A, “Cabling Specifications.” Getting Help78-13311-01 5-10Chapter 5 Universal Port Dial Feature Card Where to Go Next Troubleshooting Using the Bantam Jacks for Test Port Functionality, pageTroubleshooting Network Interfaces, page Getting Help, page LEDsLocal alarm Figure 6-2 8-Port T1 or E1 DFC LEDsFigure 6-3 T3 DFC LEDs ACTIVITY ACT OK/MAINTT1 or E1 DFC StateDescription Table 6-1 LEDs continued StateDescription Mixing WAN DFCs StateDescription One CT3 DFC and up to two T1 DFCs any combination of 2, 4, or 8-portEnvironment Monitoring OverviewFigure 6-5 Slot Numbering on the Cisco AS5350 Chassis Figure 6-6 Slot Numbering on the Cisco AS5400 Chassisoutlet is measured as 27C/80F Displaying Environment Statusinlet is measured as 22C/71F 78-13311-01 Chapter 6 Troubleshooting Environment MonitoringRouter show environment Drop and Insert Mode for the CT3 DFC Using the Bantam Jacks for Test Port FunctionalityMonitoring Mode for the T1, E1 and T3 DFCs Troubleshooting Network Interfaces 6-10Getting Help Router# test trunk drop-insert on t1portCabling Specifications T1 and E1 Cable and Port Pinouts2-Port and 4-Port T1 or E1 DFC A P P E N D I X ASignal DirectionDB-15 Pin SignalBNC Pin Twinax PinRJ-45 TE Pin SignalRJ-45 NT Pin RJ-45 T1 PinSignal Signal8-Port T1 or E1 DFC BareCable Description Part NumberMale and Female RJ-45 CAB-DFC-OCTAL-xMF FromSignal SignalSignal SignalMale and Female RJ-45 CAB-DFC-OCTAL-xMF FromAttaching the 8-Port Interface Cable to a Bracket Optional Page A-10 A-11 Figure A-10 Securing the Cable Bracket to the RackA-12 Figure A-11 Connecting the 36-Pin Cable Connector to an 8-Port T1 DFCCT3 Cable and Port Pinouts Bantam Jack Port PinoutsA-13 Description78-13311-01 A-14Appendix A Cabling Specifications Bantam Jack Port Pinouts IN-1 NumericsI N D E IN-2 IN-3 IN-4 IN-5 78-13311-01 IN-6Index