Manuals / Cisco Systems / Computer Equipment / Network Card

Cisco Systems AS5400 Router# busyout slot-number, Router# clear port slot-number/port number

Models: AS5400

1 88

Download 88 pages 63.81 Kb

Page 43

Figure 4-3 Slot Numbering on the Cisco AS5400 Chassis

Chapter 4 T3 Dial Feature Card

Online Installation and Removal (OIR) of the T3 DFC

Figure 4-3 Slot Numbering on the Cisco AS5400 Chassis





		Slot 0		Slot 1
	Slot	2			Slot	3
Slot	4					Slot	5

34977

Slot 6

Slot 7

Step 2 Initialize the software busyout procedure by entering the busyout command:

Router# busyout slot-number

Step 3 Enter the show busyout command to check busyout status for that specific slot:

Router# show busyout slot-number

Step 4 You may use the clear port command to immediately disable active calls on the universal port card. Use the show controller command to show the universal port card associated with the T1 or E1 DFC.

Router# show controller t1/e1 slot-number/control-number timeslot timeslot-number

Router# clear port slot-number/port number

Note The clear port command only applies to the universal port DFC.

Step 5 Verify that the OIR/MAINT LED is off; this indicates that the DFC is offline and ready to be removed.

Note The OK/MAINT LED is green before you enter the busyout command. After you enter the busyout command, the LED changes to yellow. The LED turns off after all calls are disconnected and resources are taken out of service, indicating that busyout is complete.

Step 6 Attach an ESD-preventive wrist strap.

Warning Do not work on the system or connect or disconnect cables during periods of lightning activity. To see translations of the warnings that appear in this publication, refer to the Regulatory Compliance and Safety Information document that accompanied this device.

Step 7 Disconnect all interface cables from the DFC and secure them out of the way.

Note OIR of the T3 DFC is similar to that of the T1 or E1 DFC. To see an example of the output during online insertion and removal of an E1 DFC refer to Chapter 3, “T1 and E1 Dial Feature Cards”

Cisco AS5350 and Cisco AS5400 Universal Gateway Card Installation Guide

	78-13311-01	4-3

Image 43

Cisco Systems AS5400 manual Router# busyout slot-number, Router# clear port slot-number/port number

Contents

Cisco Systems, Inc 170 West Tasman Drive San Jose, CA Corporate HeadquartersInstallation Guide Cisco AS5350 and Cisco AS5400 Universal Gateway CardAll rights reserved Turn the television or radio antenna until the interference stopsCisco AS5350 and Cisco AS5400 Universal Gateway Card Copyright 2001, Cisco Systems, IncPreface Safety Warnings, Recommendations, and Tools RequiredOnline Installation and Removal of the T1 or E1 DFC Where to Go NextOverview ConfigurationTroubleshooting VerificationAttaching the 8-Port Interface Cable to a Bracket Optional A-5 Cabling SpecificationsContents Getting Help78-13311-01 ContentsT1 and E1 Dial Feature Related Documentation, page New Hardware Features, pageSafety Warnings Dial Feature Card andConvention TroubleshootingCabling Specifications Document ConventionsWaarschuwing Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel kan veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij elektrische schakelingen betrokken risicos en dient u op de hoogte te zijn van standaard maatregelen om ongelukken te voorkomen. Voor vertalingen van de waarschuwingen die in deze publicatie verschijnen, kunt u het document Regulatory Compliance and Safety Information Informatie over naleving van veiligheids- en andere voorschriften raadplegen dat bij dit toestel is ingesloten Page Ordering Documentation Obtaining DocumentationWorld Wide Web Documentation CD-ROMTechnical Assistance Center Contacting TAC by Using the Cisco TAC WebsiteObtaining Technical Assistance Cisco.comxiii New Hardware FeaturesRelated Documentation Contacting TAC by Telephone78-13311-01 Preface New Hardware FeaturesRequired Tools and Equipment, page Where to Go Next, page Safety Warnings, Recommendations, and Tools RequiredGeneral Safety General Safety, page Maintaining Safety with Electricity, pageMaintaining Safety with Electricity Required Tools and Equipment Preventing Electrostatic DischargeChapter 4, “T3 Dial Feature Card” Where to Go NextChapter 2, “Dial Feature Card and Carrier Card Guidelines” Chapter 3, “T1 and E1 Dial Feature Cards”Dial Feature Cards Dial Feature Card and Carrier Card GuidelinesRemoving and Installing Populated Carrier Cards, page Getting Help, page Where to Go Next, pageChapter 4, “T3 Dial Feature Card,” to perform OIR of the T3 DFC Removing and Installing Populated Carrier CardsOnline Insertion and Removal OIR of DFCs Step 1 Power off the chassis Removing a Populated Carrier CardTo remove a populated carrier card, follow the steps below card Figure 2-3 Loosen the Captive Screws on the Cisco AS5400Figure 2-4 Removing the Carrier Card from the Cisco AS5350 Figure 2-5 Removing the Carrier Card from the Cisco AS5400Installing a Populated Carrier Card Step 6 Reconnect all interface cables Chapter 6, “Troubleshooting.” Appendix A, “Cabling Specifications.” Chapter 3, “T1 and E1 Dial Feature Cards.”Chapter 4, “T3 Dial Feature Card.” Chapter 5, “Universal Port Dial Feature Card.”Where to Go Next Chapter 2 Dial Feature Card and Carrier Card Guidelines78-13311-01 Where to Go Next, page T1 and E1 Dial Feature CardsOnline Installation and Removal of the T1 or E1 DFC, page Configuring Input Impedance for the E1 DFC, page Getting Help, pageTable 3-2 E1 DFC Network Specifications SpecificationSpecification Table 3-1 T1 DFC Network SpecificationsOverview Online Installation and Removal of the T1 or E1 DFCRemoving the T1 or E1 DFC Router# clear port slot-number/port number Router# busyout slot-numberNote The clear port command only applies to the universal port DFC Figure 3-7 Loosen the Captive Screws on the Cisco AS5400 Figure 3-6 Loosen the Captive Screws on the Cisco AS5350Rx Tx Figure 3-9 Remove the DFC from the Cisco AS5400 Figure 3-8 Remove the DFC from the Cisco AS5350Figure 3-10 Blank DFC Cover Router# show busyout Chapter 3 T1 and E1 Dial Feature CardsOnline Installation and Removal of the T1 or E1 DFC Router# show controller e1 6/0 timeslotshow chassis slot Chapter 3 T1 and E1 Dial Feature CardsOnline Installation and Removal of the T1 or E1 DFC Router# show busyoutInstalling the T1 or E1 DFC Figure 3-14 Tighten the Captive Screws on the Cisco AS5400 3-10Figure 3-12 Install the T1 or E1 DFC in the Cisco AS5400 Figure 3-13 Tighten the Captive Screws on the Cisco AS5350Verification Configuring Input Impedance for the E1 DFCConfiguration Commandservice udp-small-servers service tcp-small-servers 3-12Chapter 3 T1 and E1 Dial Feature Cards Configuring Input Impedance for the E1 DFCChapter 3 T1 and E1 Dial Feature Cards 3-13Configuring Input Impedance for the E1 DFC Chapter 5, “Universal Port Dial Feature Card.” 3-14Where to Go Next Chapter 4, “T3 Dial Feature Card.”Overview T3 Dial Feature CardOnline Installation and Removal OIR of the T3 DFC, page Getting Help, page Where to Go Next, pageFigure 4-2 Slot Numbering on the Cisco AS5350 Chassis Online Installation and Removal OIR of the T3 DFCRemoving the T3 DFC OverviewRouter# clear port slot-number/port number Router# busyout slot-numberFigure 4-3 Slot Numbering on the Cisco AS5400 Chassis Figure 4-5 Loosen the Captive Screws on the Cisco AS5400 Figure 4-4 Loosen the Captive Screws on the Cisco AS5350Figure 4-8 Blank DFC Cover Installing the T3 DFCFigure 4-6 Remove the DFC from the Cisco AS5350 Figure 4-7 Remove the DFC from the Cisco AS5400Figure 4-10 Install the T3 DFC in the Cisco AS5400 Figure 4-9 Install the T3 DFC in the Cisco AS5350Figure 4-11 Tighten the Captive Screws on the Cisco AS5350 Getting Help Where to Go NextChapter 5, “Universal Port Dial Feature Card.” Chapter 6, “Troubleshooting.” Appendix A, “Cabling Specifications.”78-13311-01 Chapter 4 T3 Dial Feature Card Where to Go NextOverview Universal Port Dial Feature CardSPE Firmware, page Getting Help, page Where to Go Next, page Online Insertion and Removal OIR of the Universal Port DFC, pageFigure 5-2 Slot Numbering on the Cisco AS5350 Chassis Online Insertion and Removal OIR of the Universal Port DFCRemoving the Universal Port DFC OverviewRouter# clear port slot-number/port number Router# busyout slot-numberFigure 5-3 Slot Numbering on the Cisco AS5400 Chassis Figure 5-5 Loosen the Captive Screws on the Cisco AS5400 Figure 5-4 Loosen the Captive Screws on the Cisco AS5350Figure 5-6 Remove the DFC from the Cisco AS5350 Online Insertion and Removal OIR of the Universal Port DFC Chapter 5 Universal Port Dial Feature CardFigure 5-7 Remove the DFC from the Cisco AS5400 Figure 5-8 Blank DFC CoverRouter# show busyout Chapter 5 Universal Port Dial Feature CardOnline Insertion and Removal OIR of the Universal Port DFC Router# clear portFigure 5-9 Install the Universal Port DFC in the Cisco AS5350 Installing the Universal Port DFCFigure 5-10 Install the Universal Port DFC in the Cisco AS5400 Figure 5-12 Tighten the Captive Screws on the Cisco AS5400 Figure 5-11 Tighten the Captive Screws on the Cisco AS5350Getting Help SPE FirmwareWhere to Go Next Chapter 6, “Troubleshooting.” Appendix A, “Cabling Specifications.”Chapter 5 Universal Port Dial Feature Card Where to Go Next 5-1078-13311-01 LEDs TroubleshootingUsing the Bantam Jacks for Test Port Functionality, page Troubleshooting Network Interfaces, page Getting Help, pageACTIVITY ACT OK/MAINT Local alarmFigure 6-2 8-Port T1 or E1 DFC LEDs Figure 6-3 T3 DFC LEDsDescription StateT1 or E1 DFC Description StateTable 6-1 LEDs continued One CT3 DFC and up to two T1 DFCs any combination of 2, 4, or 8-port Mixing WAN DFCsState DescriptionFigure 6-6 Slot Numbering on the Cisco AS5400 Chassis Environment MonitoringOverview Figure 6-5 Slot Numbering on the Cisco AS5350 Chassisinlet is measured as 22C/71F Displaying Environment Statusoutlet is measured as 27C/80F Router show environment Chapter 6 Troubleshooting Environment Monitoring78-13311-01 Monitoring Mode for the T1, E1 and T3 DFCs Using the Bantam Jacks for Test Port FunctionalityDrop and Insert Mode for the CT3 DFC Router# test trunk drop-insert on t1port Troubleshooting Network Interfaces6-10 Getting HelpA P P E N D I X A Cabling SpecificationsT1 and E1 Cable and Port Pinouts 2-Port and 4-Port T1 or E1 DFCSignal SignalDirection DB-15 PinSignal BNC PinTwinax Pin RJ-45 TE PinSignal RJ-45 NT PinRJ-45 T1 Pin SignalPart Number 8-Port T1 or E1 DFCBare Cable DescriptionSignal Male and Female RJ-45 CAB-DFC-OCTAL-xMFFrom SignalFrom SignalSignal Male and Female RJ-45 CAB-DFC-OCTAL-xMFAttaching the 8-Port Interface Cable to a Bracket Optional Page A-10 Figure A-10 Securing the Cable Bracket to the Rack A-11Figure A-11 Connecting the 36-Pin Cable Connector to an 8-Port T1 DFC A-12Description CT3 Cable and Port PinoutsBantam Jack Port Pinouts A-13Appendix A Cabling Specifications Bantam Jack Port Pinouts A-1478-13311-01 I N D E NumericsIN-1 IN-2 IN-3 IN-4 IN-5 Index IN-678-13311-01