Manuals / Cisco Systems / Computer Equipment / Network Card

Cisco Systems AS5400 manual 3-12, T1 and E1 Dial Feature Cards, 78-13311-01

Models: AS5400

1 88

Download 88 pages 63.81 Kb

Page 38

Chapter 3 T1 and E1 Dial Feature Cards

Configuring Input Impedance for the E1 DFC

service timestamps log datetime localtime show-timezone no service password-encryption

service internal

service udp-small-servers service tcp-small-servers

!

hostname Router

!

boot system flash flash:1:vdukki/c5400-i-mz enable secret 5 $1$qfO1$OYKRD2cvIJx7hfQbhrJS61


			enable password lab
		!
			bert profile default pattern 220-O.151QRSS threshold 10^-6 error-injection none duration
		10
			ip subnet-zero
			no ip domain-lookup
			ip domain-name cisco.com
		!
			isdn switch-type primary-5ess
			clock timezone PDT8 -8
			clock summer-time PDT8 recurring
			partition flash 2 8 8
		!
		!
		!
			controller E1 0
			clock source free-running
			line-termination 75-ohm
			pri-group timeslots 1-31
		!
			controller E1 1
			clock source line secondary 1
			pri-group timeslots 1-31
		!
			controller E1 2
			clock source line secondary 2
			pri-group timeslots 1-31
		!
			controller E1 3
			clock source line secondary 3
			pri-group timeslots 1-31
		!
			controller E1 4
			clock source line secondary 4
			pri-group timeslots 1-3,16
		!
			controller E1 5
			clock source line secondary 5
			pri-group timeslots 1-31
		!
			controller E1 6
			clock source line secondary 6
			pri-group timeslots 1-31
		!
			controller E1 7
			clock source line secondary 7
			pri-group timeslots 1-31
		!
		!
		!
			interface Ethernet0
			ip address 1.6.44.2 255.255.255.0
			no ip directed-broadcast
			no ip route-cache
			Cisco AS5350 and Cisco AS5400 Universal Gateway Card Installation Guide

	3-12	78-13311-01
	3-12	78-13311-01

Image 38

Cisco Systems AS5400 manual 3-12, T1 and E1 Dial Feature Cards, Configuring Input Impedance for the E1 DFC, 78-13311-01

Contents

Cisco AS5350 and Cisco AS5400 Universal Gateway Card Corporate HeadquartersInstallation Guide Cisco Systems, Inc 170 West Tasman Drive San Jose, CACopyright 2001, Cisco Systems, Inc Turn the television or radio antenna until the interference stopsCisco AS5350 and Cisco AS5400 Universal Gateway Card All rights reservedWhere to Go Next Safety Warnings, Recommendations, and Tools RequiredOnline Installation and Removal of the T1 or E1 DFC PrefaceVerification ConfigurationTroubleshooting OverviewGetting Help Cabling SpecificationsContents Attaching the 8-Port Interface Cable to a Bracket Optional A-5Contents 78-13311-01Dial Feature Card and Related Documentation, page New Hardware Features, pageSafety Warnings T1 and E1 Dial FeatureDocument Conventions TroubleshootingCabling Specifications ConventionWaarschuwing Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel kan veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij elektrische schakelingen betrokken risicos en dient u op de hoogte te zijn van standaard maatregelen om ongelukken te voorkomen. Voor vertalingen van de waarschuwingen die in deze publicatie verschijnen, kunt u het document Regulatory Compliance and Safety Information Informatie over naleving van veiligheids- en andere voorschriften raadplegen dat bij dit toestel is ingesloten Page Documentation CD-ROM Obtaining DocumentationWorld Wide Web Ordering DocumentationCisco.com Contacting TAC by Using the Cisco TAC WebsiteObtaining Technical Assistance Technical Assistance CenterContacting TAC by Telephone New Hardware FeaturesRelated Documentation xiiiPreface New Hardware Features 78-13311-01General Safety, page Maintaining Safety with Electricity, page Safety Warnings, Recommendations, and Tools RequiredGeneral Safety Required Tools and Equipment, page Where to Go Next, pageMaintaining Safety with Electricity Preventing Electrostatic Discharge Required Tools and EquipmentChapter 3, “T1 and E1 Dial Feature Cards” Where to Go NextChapter 2, “Dial Feature Card and Carrier Card Guidelines” Chapter 4, “T3 Dial Feature Card”Getting Help, page Where to Go Next, page Dial Feature Card and Carrier Card GuidelinesRemoving and Installing Populated Carrier Cards, page Dial Feature CardsOnline Insertion and Removal OIR of DFCs Removing and Installing Populated Carrier CardsChapter 4, “T3 Dial Feature Card,” to perform OIR of the T3 DFC To remove a populated carrier card, follow the steps below Removing a Populated Carrier CardStep 1 Power off the chassis Figure 2-5 Removing the Carrier Card from the Cisco AS5400 Figure 2-3 Loosen the Captive Screws on the Cisco AS5400Figure 2-4 Removing the Carrier Card from the Cisco AS5350 cardInstalling a Populated Carrier Card Step 6 Reconnect all interface cables Chapter 5, “Universal Port Dial Feature Card.” Chapter 3, “T1 and E1 Dial Feature Cards.”Chapter 4, “T3 Dial Feature Card.” Chapter 6, “Troubleshooting.” Appendix A, “Cabling Specifications.”78-13311-01 Chapter 2 Dial Feature Card and Carrier Card GuidelinesWhere to Go Next Configuring Input Impedance for the E1 DFC, page Getting Help, page T1 and E1 Dial Feature CardsOnline Installation and Removal of the T1 or E1 DFC, page Where to Go Next, pageTable 3-1 T1 DFC Network Specifications SpecificationSpecification Table 3-2 E1 DFC Network SpecificationsRemoving the T1 or E1 DFC Online Installation and Removal of the T1 or E1 DFCOverview Note The clear port command only applies to the universal port DFC Router# busyout slot-numberRouter# clear port slot-number/port number Rx Tx Figure 3-6 Loosen the Captive Screws on the Cisco AS5350Figure 3-7 Loosen the Captive Screws on the Cisco AS5400 Figure 3-10 Blank DFC Cover Figure 3-8 Remove the DFC from the Cisco AS5350Figure 3-9 Remove the DFC from the Cisco AS5400 Router# show controller e1 6/0 timeslot Chapter 3 T1 and E1 Dial Feature CardsOnline Installation and Removal of the T1 or E1 DFC Router# show busyoutRouter# show busyout Chapter 3 T1 and E1 Dial Feature CardsOnline Installation and Removal of the T1 or E1 DFC show chassis slotInstalling the T1 or E1 DFC Figure 3-13 Tighten the Captive Screws on the Cisco AS5350 3-10Figure 3-12 Install the T1 or E1 DFC in the Cisco AS5400 Figure 3-14 Tighten the Captive Screws on the Cisco AS5400Command Configuring Input Impedance for the E1 DFCConfiguration VerificationConfiguring Input Impedance for the E1 DFC 3-12Chapter 3 T1 and E1 Dial Feature Cards service udp-small-servers service tcp-small-serversConfiguring Input Impedance for the E1 DFC 3-13Chapter 3 T1 and E1 Dial Feature Cards Chapter 4, “T3 Dial Feature Card.” 3-14Where to Go Next Chapter 5, “Universal Port Dial Feature Card.”Getting Help, page Where to Go Next, page T3 Dial Feature CardOnline Installation and Removal OIR of the T3 DFC, page OverviewOverview Online Installation and Removal OIR of the T3 DFCRemoving the T3 DFC Figure 4-2 Slot Numbering on the Cisco AS5350 ChassisFigure 4-3 Slot Numbering on the Cisco AS5400 Chassis Router# busyout slot-numberRouter# clear port slot-number/port number Figure 4-4 Loosen the Captive Screws on the Cisco AS5350 Figure 4-5 Loosen the Captive Screws on the Cisco AS5400Figure 4-7 Remove the DFC from the Cisco AS5400 Installing the T3 DFCFigure 4-6 Remove the DFC from the Cisco AS5350 Figure 4-8 Blank DFC CoverFigure 4-11 Tighten the Captive Screws on the Cisco AS5350 Figure 4-9 Install the T3 DFC in the Cisco AS5350Figure 4-10 Install the T3 DFC in the Cisco AS5400 Chapter 6, “Troubleshooting.” Appendix A, “Cabling Specifications.” Where to Go NextChapter 5, “Universal Port Dial Feature Card.” Getting HelpChapter 4 T3 Dial Feature Card Where to Go Next 78-13311-01Online Insertion and Removal OIR of the Universal Port DFC, page Universal Port Dial Feature CardSPE Firmware, page Getting Help, page Where to Go Next, page OverviewOverview Online Insertion and Removal OIR of the Universal Port DFCRemoving the Universal Port DFC Figure 5-2 Slot Numbering on the Cisco AS5350 ChassisFigure 5-3 Slot Numbering on the Cisco AS5400 Chassis Router# busyout slot-numberRouter# clear port slot-number/port number Figure 5-6 Remove the DFC from the Cisco AS5350 Figure 5-4 Loosen the Captive Screws on the Cisco AS5350Figure 5-5 Loosen the Captive Screws on the Cisco AS5400 Figure 5-8 Blank DFC Cover Chapter 5 Universal Port Dial Feature CardFigure 5-7 Remove the DFC from the Cisco AS5400 Online Insertion and Removal OIR of the Universal Port DFCRouter# clear port Chapter 5 Universal Port Dial Feature CardOnline Insertion and Removal OIR of the Universal Port DFC Router# show busyoutFigure 5-10 Install the Universal Port DFC in the Cisco AS5400 Installing the Universal Port DFCFigure 5-9 Install the Universal Port DFC in the Cisco AS5350 Figure 5-11 Tighten the Captive Screws on the Cisco AS5350 Figure 5-12 Tighten the Captive Screws on the Cisco AS5400Chapter 6, “Troubleshooting.” Appendix A, “Cabling Specifications.” SPE FirmwareWhere to Go Next Getting Help78-13311-01 5-10Chapter 5 Universal Port Dial Feature Card Where to Go Next Troubleshooting Network Interfaces, page Getting Help, page TroubleshootingUsing the Bantam Jacks for Test Port Functionality, page LEDsFigure 6-3 T3 DFC LEDs Local alarmFigure 6-2 8-Port T1 or E1 DFC LEDs ACTIVITY ACT OK/MAINTT1 or E1 DFC StateDescription Table 6-1 LEDs continued StateDescription Description Mixing WAN DFCsState One CT3 DFC and up to two T1 DFCs any combination of 2, 4, or 8-portFigure 6-5 Slot Numbering on the Cisco AS5350 Chassis Environment MonitoringOverview Figure 6-6 Slot Numbering on the Cisco AS5400 Chassisoutlet is measured as 27C/80F Displaying Environment Statusinlet is measured as 22C/71F 78-13311-01 Chapter 6 Troubleshooting Environment MonitoringRouter show environment Drop and Insert Mode for the CT3 DFC Using the Bantam Jacks for Test Port FunctionalityMonitoring Mode for the T1, E1 and T3 DFCs Getting Help Troubleshooting Network Interfaces6-10 Router# test trunk drop-insert on t1port2-Port and 4-Port T1 or E1 DFC Cabling SpecificationsT1 and E1 Cable and Port Pinouts A P P E N D I X ADB-15 Pin SignalDirection SignalRJ-45 TE Pin BNC PinTwinax Pin SignalSignal RJ-45 NT PinRJ-45 T1 Pin SignalCable Description 8-Port T1 or E1 DFCBare Part NumberSignal Male and Female RJ-45 CAB-DFC-OCTAL-xMFFrom SignalMale and Female RJ-45 CAB-DFC-OCTAL-xMF SignalSignal FromAttaching the 8-Port Interface Cable to a Bracket Optional Page A-10 A-11 Figure A-10 Securing the Cable Bracket to the RackA-12 Figure A-11 Connecting the 36-Pin Cable Connector to an 8-Port T1 DFCA-13 CT3 Cable and Port PinoutsBantam Jack Port Pinouts Description78-13311-01 A-14Appendix A Cabling Specifications Bantam Jack Port Pinouts IN-1 NumericsI N D E IN-2 IN-3 IN-4 IN-5 78-13311-01 IN-6Index