Manuals / Cisco Systems / Computer Equipment / Network Card

Cisco Systems AS5400 manual Environment Monitoring, Overview

Models: AS5400

1 88

Download 88 pages 63.81 Kb

Page 64

Environment Monitoring

Chapter 6 Troubleshooting

Environment Monitoring

Environment Monitoring

Overview

The Cisco AS5350 and Cisco AS5400 contain temperature sensors to detect abnormal temperature conditions during system operation. The three levels of sensor detection are as follows:

1.When the operating temperature of the system exceeds 45° C, the system reaches a warning state. A

warning message appears on the console. When the operating temperature of the system drops below 45° C, another message is displayed on the console indicating a recovery. At this level of sensor detection, there is no disruption in system operation.

2.When the operating temperature of the system continues to rise above 45° C and reaches a temperature of 60° C, the system reaches a critical state.

Cisco IOS software busys out the DFCs in the chassis and shuts down the first DFC. If the operating temperature continues to be critical after 10 minutes, Cisco IOS software shuts down another DFC.

Note DFC slot numbering starts from the system board and works up from left to right. Slot 0 is reserved for the motherboard. The DFC slots are numbered sequentially. (See Figure 6-5and Figure 6-6.)

Figure 6-5 Slot Numbering on the Cisco AS5350 Chassis




			Slot 0
	Slot 2		Slot 0		Slot 1		Slot 3
					Slot 1		Slot 3

36006

Figure 6-6 Slot Numbering on the Cisco AS5400 Chassis





		Slot 0		Slot 1
	Slot	2			Slot	3
Slot	4					Slot	5

34977

Slot 6

Slot 7

The busyout process is repeated at 10 minute intervals until the final DFC is shut down. The console displays the slot number of the DFC and the type of DFC that was shut down.

Cisco AS5350 and Cisco AS5400 Universal Gateway Card Installation Guide

6-6	78-13311-01

Image 64

Cisco Systems AS5400 manual Environment Monitoring, Overview, 5 Slot Numbering on the Cisco AS5350 Chassis

Contents

Corporate Headquarters Installation GuideCisco AS5350 and Cisco AS5400 Universal Gateway Card Cisco Systems, Inc 170 West Tasman Drive San Jose, CATurn the television or radio antenna until the interference stops Cisco AS5350 and Cisco AS5400 Universal Gateway CardCopyright 2001, Cisco Systems, Inc All rights reservedSafety Warnings, Recommendations, and Tools Required Online Installation and Removal of the T1 or E1 DFCWhere to Go Next PrefaceConfiguration TroubleshootingVerification OverviewCabling Specifications ContentsGetting Help Attaching the 8-Port Interface Cable to a Bracket Optional A-5Contents 78-13311-01Related Documentation, page New Hardware Features, page Safety WarningsDial Feature Card and T1 and E1 Dial FeatureTroubleshooting Cabling SpecificationsDocument Conventions ConventionWaarschuwing Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel kan veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij elektrische schakelingen betrokken risicos en dient u op de hoogte te zijn van standaard maatregelen om ongelukken te voorkomen. Voor vertalingen van de waarschuwingen die in deze publicatie verschijnen, kunt u het document Regulatory Compliance and Safety Information Informatie over naleving van veiligheids- en andere voorschriften raadplegen dat bij dit toestel is ingesloten Page Obtaining Documentation World Wide WebDocumentation CD-ROM Ordering DocumentationContacting TAC by Using the Cisco TAC Website Obtaining Technical AssistanceCisco.com Technical Assistance CenterNew Hardware Features Related DocumentationContacting TAC by Telephone xiiiPreface New Hardware Features 78-13311-01Safety Warnings, Recommendations, and Tools Required General SafetyGeneral Safety, page Maintaining Safety with Electricity, page Required Tools and Equipment, page Where to Go Next, pageMaintaining Safety with Electricity Preventing Electrostatic Discharge Required Tools and EquipmentWhere to Go Next Chapter 2, “Dial Feature Card and Carrier Card Guidelines”Chapter 3, “T1 and E1 Dial Feature Cards” Chapter 4, “T3 Dial Feature Card”Dial Feature Card and Carrier Card Guidelines Removing and Installing Populated Carrier Cards, pageGetting Help, page Where to Go Next, page Dial Feature CardsChapter 4, “T3 Dial Feature Card,” to perform OIR of the T3 DFC Removing and Installing Populated Carrier CardsOnline Insertion and Removal OIR of DFCs Step 1 Power off the chassis Removing a Populated Carrier CardTo remove a populated carrier card, follow the steps below Figure 2-3 Loosen the Captive Screws on the Cisco AS5400 Figure 2-4 Removing the Carrier Card from the Cisco AS5350Figure 2-5 Removing the Carrier Card from the Cisco AS5400 cardInstalling a Populated Carrier Card Step 6 Reconnect all interface cables Chapter 3, “T1 and E1 Dial Feature Cards.” Chapter 4, “T3 Dial Feature Card.”Chapter 5, “Universal Port Dial Feature Card.” Chapter 6, “Troubleshooting.” Appendix A, “Cabling Specifications.”Where to Go Next Chapter 2 Dial Feature Card and Carrier Card Guidelines78-13311-01 T1 and E1 Dial Feature Cards Online Installation and Removal of the T1 or E1 DFC, pageConfiguring Input Impedance for the E1 DFC, page Getting Help, page Where to Go Next, pageSpecification SpecificationTable 3-1 T1 DFC Network Specifications Table 3-2 E1 DFC Network SpecificationsOverview Online Installation and Removal of the T1 or E1 DFCRemoving the T1 or E1 DFC Router# clear port slot-number/port number Router# busyout slot-numberNote The clear port command only applies to the universal port DFC Figure 3-7 Loosen the Captive Screws on the Cisco AS5400 Figure 3-6 Loosen the Captive Screws on the Cisco AS5350Rx Tx Figure 3-9 Remove the DFC from the Cisco AS5400 Figure 3-8 Remove the DFC from the Cisco AS5350Figure 3-10 Blank DFC Cover Chapter 3 T1 and E1 Dial Feature Cards Online Installation and Removal of the T1 or E1 DFCRouter# show controller e1 6/0 timeslot Router# show busyoutChapter 3 T1 and E1 Dial Feature Cards Online Installation and Removal of the T1 or E1 DFCRouter# show busyout show chassis slotInstalling the T1 or E1 DFC 3-10 Figure 3-12 Install the T1 or E1 DFC in the Cisco AS5400Figure 3-13 Tighten the Captive Screws on the Cisco AS5350 Figure 3-14 Tighten the Captive Screws on the Cisco AS5400Configuring Input Impedance for the E1 DFC ConfigurationCommand Verification3-12 Chapter 3 T1 and E1 Dial Feature CardsConfiguring Input Impedance for the E1 DFC service udp-small-servers service tcp-small-serversChapter 3 T1 and E1 Dial Feature Cards 3-13Configuring Input Impedance for the E1 DFC 3-14 Where to Go NextChapter 4, “T3 Dial Feature Card.” Chapter 5, “Universal Port Dial Feature Card.”T3 Dial Feature Card Online Installation and Removal OIR of the T3 DFC, pageGetting Help, page Where to Go Next, page OverviewOnline Installation and Removal OIR of the T3 DFC Removing the T3 DFCOverview Figure 4-2 Slot Numbering on the Cisco AS5350 ChassisRouter# clear port slot-number/port number Router# busyout slot-numberFigure 4-3 Slot Numbering on the Cisco AS5400 Chassis Figure 4-4 Loosen the Captive Screws on the Cisco AS5350 Figure 4-5 Loosen the Captive Screws on the Cisco AS5400Installing the T3 DFC Figure 4-6 Remove the DFC from the Cisco AS5350Figure 4-7 Remove the DFC from the Cisco AS5400 Figure 4-8 Blank DFC CoverFigure 4-10 Install the T3 DFC in the Cisco AS5400 Figure 4-9 Install the T3 DFC in the Cisco AS5350Figure 4-11 Tighten the Captive Screws on the Cisco AS5350 Where to Go Next Chapter 5, “Universal Port Dial Feature Card.”Chapter 6, “Troubleshooting.” Appendix A, “Cabling Specifications.” Getting HelpChapter 4 T3 Dial Feature Card Where to Go Next 78-13311-01Universal Port Dial Feature Card SPE Firmware, page Getting Help, page Where to Go Next, pageOnline Insertion and Removal OIR of the Universal Port DFC, page OverviewOnline Insertion and Removal OIR of the Universal Port DFC Removing the Universal Port DFCOverview Figure 5-2 Slot Numbering on the Cisco AS5350 ChassisRouter# clear port slot-number/port number Router# busyout slot-numberFigure 5-3 Slot Numbering on the Cisco AS5400 Chassis Figure 5-5 Loosen the Captive Screws on the Cisco AS5400 Figure 5-4 Loosen the Captive Screws on the Cisco AS5350Figure 5-6 Remove the DFC from the Cisco AS5350 Chapter 5 Universal Port Dial Feature Card Figure 5-7 Remove the DFC from the Cisco AS5400Figure 5-8 Blank DFC Cover Online Insertion and Removal OIR of the Universal Port DFCChapter 5 Universal Port Dial Feature Card Online Insertion and Removal OIR of the Universal Port DFCRouter# clear port Router# show busyoutFigure 5-9 Install the Universal Port DFC in the Cisco AS5350 Installing the Universal Port DFCFigure 5-10 Install the Universal Port DFC in the Cisco AS5400 Figure 5-11 Tighten the Captive Screws on the Cisco AS5350 Figure 5-12 Tighten the Captive Screws on the Cisco AS5400SPE Firmware Where to Go NextChapter 6, “Troubleshooting.” Appendix A, “Cabling Specifications.” Getting HelpChapter 5 Universal Port Dial Feature Card Where to Go Next 5-1078-13311-01 Troubleshooting Using the Bantam Jacks for Test Port Functionality, pageTroubleshooting Network Interfaces, page Getting Help, page LEDsLocal alarm Figure 6-2 8-Port T1 or E1 DFC LEDsFigure 6-3 T3 DFC LEDs ACTIVITY ACT OK/MAINTDescription StateT1 or E1 DFC Description StateTable 6-1 LEDs continued Mixing WAN DFCs StateDescription One CT3 DFC and up to two T1 DFCs any combination of 2, 4, or 8-portEnvironment Monitoring OverviewFigure 6-5 Slot Numbering on the Cisco AS5350 Chassis Figure 6-6 Slot Numbering on the Cisco AS5400 Chassisinlet is measured as 22C/71F Displaying Environment Statusoutlet is measured as 27C/80F Router show environment Chapter 6 Troubleshooting Environment Monitoring78-13311-01 Monitoring Mode for the T1, E1 and T3 DFCs Using the Bantam Jacks for Test Port FunctionalityDrop and Insert Mode for the CT3 DFC Troubleshooting Network Interfaces 6-10Getting Help Router# test trunk drop-insert on t1portCabling Specifications T1 and E1 Cable and Port Pinouts2-Port and 4-Port T1 or E1 DFC A P P E N D I X ASignal DirectionDB-15 Pin SignalBNC Pin Twinax PinRJ-45 TE Pin SignalRJ-45 NT Pin RJ-45 T1 PinSignal Signal8-Port T1 or E1 DFC BareCable Description Part NumberMale and Female RJ-45 CAB-DFC-OCTAL-xMF FromSignal SignalSignal SignalMale and Female RJ-45 CAB-DFC-OCTAL-xMF FromAttaching the 8-Port Interface Cable to a Bracket Optional Page A-10 A-11 Figure A-10 Securing the Cable Bracket to the RackA-12 Figure A-11 Connecting the 36-Pin Cable Connector to an 8-Port T1 DFCCT3 Cable and Port Pinouts Bantam Jack Port PinoutsA-13 DescriptionAppendix A Cabling Specifications Bantam Jack Port Pinouts A-1478-13311-01 I N D E NumericsIN-1 IN-2 IN-3 IN-4 IN-5 Index IN-678-13311-01