Cisco Systems Cisco AS5350, Cisco AS5400 - page 52

52

Step2 Enter global configuration mode. You are in global configuration mode when the prompt changes to Gateway(config)#.

Gateway# configure terminal

Enter configuration commands, one per line. End with CNTL/Z.

Gateway(config)#

Step3 Specify the country to set the DFC parameters (including country code and encoding). This setting is applied at the

system level. All DFCs use the same country code. The default is usa if the gateway is configured with T1 interfaces and

e1-default if the gateway is configured with E1 interfaces. Use the no form of this command to set the country code to

the default of domestic.

Note All sessions on all DFCs in all slots must be idle for this command to run.

Gateway(config)# spe country country name

Step4 Enter the numbers of the ports to configure. If you want to configure 108 ports on slot 3, enter line 3/00 3/107. If you

want to configure 324 ports on slots 3-5, enter line 3/00 5/107.

Gateway(config)# line slot/port slot/port

Gateway(config-line)#

Step5 Allow all protocols to be used when connecting to the line:

Gateway(config-line)# transport input all

Step6 Enable remote IP users running a PPP application to dial in, bypass the EXEC facility, and connect directly to the

network:

Gateway(config-line)# autoselect ppp

Step7 Enable incoming and outgoing calls:

Gateway(config-line)# modem inout

Step8 Return to privileged EXEC mode:

Gateway(config-line)# Ctrl-Z

Gateway#

Tip To save the gateway configuration, save it to NVRAM. Refer to the “Saving Configuration Changes” section on

page 57.

Verify

To verify your SPE configuration:

•To display a summary for all the lines, enter the show spe command:

Gateway# show spe

SPE settings:

==============

Country code configuration: default T1 (u Law)

Polling interval: 8 secs.

History log events: 50(per port)

Port legends:

============

Port state: (s)shutdown (t)test (r)recovery (d)download

(b)busiedout (p)busyout pending, (B)bad (a)active call

Call type: (m)modem (d)digital (f)fax-relay (v)voice (_)not in use

System resources summary:

======================

Contents

Main Quick Start Guide Cisco AS5350 and Cisco AS5400 Universal Gateways 1 User Documentation To access online user documentation: To access user documentation on the Documentation CD-ROM: Cisco AS5350 and Cisco AS5400 Universal Gateway Documentation Cisco IOS Software Documentation Items Included with Cisco AS5350 and Cisco AS5400 Universal Gateways Items Not Included 2 Safety Information Setting Up the Chassis Rack-Mounting the Chassis Required Tools and Equipment Attaching Brackets Installation in a Rack Desktop Installation Chassis Ground Connection 3 Installing Carrier Cards Installing a Carrier Card Page Installing DFCs Gateway Software Configuration Guide. Installing a DFC in a Cisco AS5350 Tighten the Captive Screws on the Cisco AS5350 Installing a DFC in a Cisco AS5400 DFC LED State Description 4 DFC LED State Description System Management and Power Connections Port or Connection WAN, LAN, and Voice Connections Connect a Console Terminal Color or Type Connected to: Cable Connecting Cisco AS5350 to Console Terminal Connecting Cisco AS5400 to Console Terminal Guide Connect to Ethernet Network Connect to a WAN Connecting 2-Port or 4-Port DFC on Cisco AS5350 to RJ-45 Jack RJ-45 jack Connecting 8-Port DFC on Cisco AS5350 to RJ-45 Jack Straight-through RJ-45-to-RJ-45 cable Configuration Guide Page Connecting 8-Port DFC on Cisco AS5400 to RJ-45 Jack Connect each T3 DFC to a T3 CSU/DSU with two 75-ohm BNC cables Connecting T3 DFC on Cisco AS5350 to T3 CSU/DSU Connecting T3 DFC on Cisco AS5400 to T3 CSU/DSU Connect a synchronous serial port to a modem or a CSU/DSU with a serial transition cable. Connecting Serial Port on Cisco AS5350 to CSU/DSU Page Page Connect AC Power Alarm Pinouts Pin Description Connect DC Power Page A- A+ B- B+ to the stripped ends of the ground and input wires. 5 Checklist for Power Up Power-Up Procedure 6 Initial Configuration Using the Setup Command Facility Step3 When the following message appears, press Return to see the current interface summary: Step4 Enter a host name for the gateway: Step8 Respond to the following prompts as appropriate for your network: Step10 Enter yes to allow users to dial in via ISDN or analog modems: Step12 Press Enter for every slot, port, and channel: Initial Configuration Using CLI (Manual Configuration) Page Configuring Local AAA Security Configure Basic Dial Access Configuring the Asynchronous Group Interface Step5 Return to privileged EXEC mode: Configuring a Channelized T1 or E1 DFC Configuring a Channelized T3 DFC Page Configuring ISDN PRI Request PRI Line and Switch Configuration from a Telco Service Provider Area Keyword Switch Type Page Enter the show isdn status command to view layer status information: Monitor ISDN channels and service by entering the show isdn service command: Configuring the D Channels for ISDN Signaling Page Configuring the Universal Port Dial Feature Card and Lines SPE Firmware Feature Description Compression protocols V.42bis (includes MNP 5) Page Configure Clocking Dial Feature Card Ports External Clock Free-Running Clock Clocking Configuration Examples Verify your TDM clock history by using the show tdm clocks command (this example is for CT3): Verify your user-configured trunk clock selection by using the show tdm clocks command: Verify your free-running clock selection by using the show tdm clocks command: Saving Configuration Changes Voice over IP Prerequisites Configuration Tasks Where to Go Next For detailed configuration information for specific features: For new features associated with a software release: 7 8 Cisco.com Documentation CD-ROM Ordering Documentation 9 Cisco.com Technical Assistance Center Cisco TAC Website Cisco TAC Escalation Center 10 Page Cisco Web site at www.cisco.com/go/offices