Cisco Systems Cisco AS5350, Cisco AS5400 Attaching Brackets

Required Tools and Equipment

You need the following tools and equipment to rack-mount the chassis:

•Number 2 Phillips screwdriver (not included)

•Medium flat-blade screwdriver (not included)

•Screws for attaching the chassis to the rack (not included)

•Standard rack-mount brackets (included)

•Screws for attaching the brackets to the chassis (included)

Attaching Brackets

Attach the mounting brackets to the chassis as shown, using the screws provided. Attach the second bracket to the opposite side

of the chassis.

Note The chassis may be installed with either the front or rear panel facing forward.

Cisco AS5350 Bracket Installation—Front Panel Forward (19-Inch Rack)

Cisco AS5400 Bracket Installation—Front Panel Forward (19-Inch Rack)

35669

Note: The second bracket attaches to the other side of the chassis.

The chassis can also be installed with the rear panel forward.

H10643

Contents

Main Quick Start Guide Cisco AS5350 and Cisco AS5400 Universal Gateways 1 User Documentation To access online user documentation: To access user documentation on the Documentation CD-ROM: Cisco AS5350 and Cisco AS5400 Universal Gateway Documentation Cisco IOS Software Documentation Items Included with Cisco AS5350 and Cisco AS5400 Universal Gateways Items Not Included 2 Safety Information Setting Up the Chassis Rack-Mounting the Chassis Required Tools and Equipment Attaching Brackets Installation in a Rack Desktop Installation Chassis Ground Connection 3 Installing Carrier Cards Installing a Carrier Card Page Installing DFCs Gateway Software Configuration Guide. Installing a DFC in a Cisco AS5350 Tighten the Captive Screws on the Cisco AS5350 Installing a DFC in a Cisco AS5400 DFC LED State Description 4 DFC LED State Description System Management and Power Connections Port or Connection WAN, LAN, and Voice Connections Connect a Console Terminal Color or Type Connected to: Cable Connecting Cisco AS5350 to Console Terminal Connecting Cisco AS5400 to Console Terminal Guide Connect to Ethernet Network Connect to a WAN Connecting 2-Port or 4-Port DFC on Cisco AS5350 to RJ-45 Jack RJ-45 jack Connecting 8-Port DFC on Cisco AS5350 to RJ-45 Jack Straight-through RJ-45-to-RJ-45 cable Configuration Guide Page Connecting 8-Port DFC on Cisco AS5400 to RJ-45 Jack Connect each T3 DFC to a T3 CSU/DSU with two 75-ohm BNC cables Connecting T3 DFC on Cisco AS5350 to T3 CSU/DSU Connecting T3 DFC on Cisco AS5400 to T3 CSU/DSU Connect a synchronous serial port to a modem or a CSU/DSU with a serial transition cable. Connecting Serial Port on Cisco AS5350 to CSU/DSU Page Page Connect AC Power Alarm Pinouts Pin Description Connect DC Power Page A- A+ B- B+ to the stripped ends of the ground and input wires. 5 Checklist for Power Up Power-Up Procedure 6 Initial Configuration Using the Setup Command Facility Step3 When the following message appears, press Return to see the current interface summary: Step4 Enter a host name for the gateway: Step8 Respond to the following prompts as appropriate for your network: Step10 Enter yes to allow users to dial in via ISDN or analog modems: Step12 Press Enter for every slot, port, and channel: Initial Configuration Using CLI (Manual Configuration) Page Configuring Local AAA Security Configure Basic Dial Access Configuring the Asynchronous Group Interface Step5 Return to privileged EXEC mode: Configuring a Channelized T1 or E1 DFC Configuring a Channelized T3 DFC Page Configuring ISDN PRI Request PRI Line and Switch Configuration from a Telco Service Provider Area Keyword Switch Type Page Enter the show isdn status command to view layer status information: Monitor ISDN channels and service by entering the show isdn service command: Configuring the D Channels for ISDN Signaling Page Configuring the Universal Port Dial Feature Card and Lines SPE Firmware Feature Description Compression protocols V.42bis (includes MNP 5) Page Configure Clocking Dial Feature Card Ports External Clock Free-Running Clock Clocking Configuration Examples Verify your TDM clock history by using the show tdm clocks command (this example is for CT3): Verify your user-configured trunk clock selection by using the show tdm clocks command: Verify your free-running clock selection by using the show tdm clocks command: Saving Configuration Changes Voice over IP Prerequisites Configuration Tasks Where to Go Next For detailed configuration information for specific features: For new features associated with a software release: 7 8 Cisco.com Documentation CD-ROM Ordering Documentation 9 Cisco.com Technical Assistance Center Cisco TAC Website Cisco TAC Escalation Center 10 Page Cisco Web site at www.cisco.com/go/offices