Manuals / Cisco Systems / Computer Equipment / Network Card

Cisco Systems 10BASE-FL, PA-5EFL= manual Configuring the 5EFL Interfaces

Models: 10BASE-FL PA-5EFL=

1 40

Download 40 pages 63.82 Kb

Page 37

Configuring the 5EFL Interfaces

For complete descriptions of interface subcommands and the conﬁguration options available for Cisco 7200 series-related interfaces and functionality, refer to the publications listed in the section “If You Need More Information” on page 2.

PA-5EFL Ethernet 10BASE-FL Port Adapter Installation and Configuration 37

Image 37

Cisco Systems 10BASE-FL, PA-5EFL= manual Configuring the 5EFL Interfaces

Contents

Introduction ContentsPA-5EFL Ethernet 10BASE-FL Port Adapter Installation and Conﬁguration Product Numbers PA-5EFL and PA-5EFL=If You Need More Information Port Adapter Installation PrerequisitesCisco 7202 Installation and Conﬁguration Guide Cisco 7204 Installation and Conﬁguration GuideSoftware and Hardware Requirements Tools and Parts RequiredSafety Warnings Safety GuidelinesDisconnect all power and external cables before moving a chassis Ethernet and Ethernet 10BASE-FL Overview IEEE 802.3 10BASE-FL Speciﬁcations What Is the 5EFL Port Adapter? Figure 3 Two Port Adapters on a VIP2-50 Horizontal Orientation Shown 5EFL Port Adapter LEDs 5EFL Port Adapter Multimode Fiber-Optic Cable and Receptacles VIP2 and the 5EFL Port AdapterVIP2 and the 5EFL Port Adapter VIP2-15 or VIP2-40 with Two 5EFL Port Adapter Installed HorizontalOrientation Shown H6472Installing or Replacing a Port Adapter on a VIP2 H3148 ScrewH3149 H3150 Carrier Upper edge Lower edgeH3152 Conﬁguring the 5EFL Interfaces Attaching 5EFL Port Adapter Interface CablesFigure 13 Connecting 5EFL Port Adapter ST Cable Pairs Attaching 5EFL Port Adapter Interface CablesProtocols you plan to route on each new interface Use the following procedure to perform a basic conﬁguration show startup-conﬁg command. Verify show running-conﬁg command. DisplayUsing show Commands to Display Interface Information ARP type ARPA, ARP Timeout Ethernet3/1/0 is administratively down, line protocol is downRouter# sh int e 3/1/0 5 minute output rate 0 bits/sec, 0 packets/secRouter# show version Router# show diag Using the ping CommandCisco 7200 Series and the 5EFL Port Adapter Cisco 7200 Series and the 5EFL Port AdapterFigure 15 Cisco 7206 with a 5EFL Port Adapter in Port Adapter Slot Installing or Replacing a Port Adapter in Cisco 7200 Series Routers Figure 17 Handling a Port Adapter Installing or Replacing a Port Adapter in Cisco 7200 Series RoutersMetal carrier Printed circuit board H6597 Replacing a Port AdapterH6747 Port adapter lever locked positionAttaching 5EFL Port Adapter Interface Cables Conﬁguring the 5EFL Interfaces port numbers 2/0, 2/1, 2/2 and 2/3 from left ot right 5 EFL port adapterH6772 Step 6 Conﬁgure additional interfaces as required the conﬁguration stored in NVRAM using the show running-conﬁg command. Displayshow startup-conﬁg command. Verify Display the running conﬁguration ﬁle with theThe following example of the show interfaces ethernet slot/port command shows all of the information speciﬁc to the ﬁrst 5EFL interface port interface port 0 in port adapter slot Page Configuring the 5EFL Interfaces Documentation CD-ROM Cisco Connection OnlineDocumentation CD-ROM Documentation CD-ROM