Manuals / Cisco Systems / Computer Equipment / Switch

Cisco Systems WS-C6513-E-RF, 6500-E manual Module Top View with Port Adapters Installed, Standoffs

Models: 6513-E 6500-E WS-C6513-E-RF

1 34

Download 34 pages 43.44 Kb

Page 21

Figure 12 Module (Top View with Port Adapters Installed)

Removing and Replacing Port Adapters

Figure 12 Module (Top View with Port Adapters Installed)

Slot 4 standoffs (2)

Standoffs (6)

Phillips screws (6)

WS-X6600	WS-X6600-6TI	1	2	3	4	5	6	WS-X6600-6EI 1	2	3	4	5	6
STATUS
AVVID Services Module	6Port TI Intfc Mdl							6Port EI Intfc Mdl

Slot 4 Phillips

screws (2)

MDL	68453
REAR	68453
STATUS

Figure 13 Module (Top View with Port Adapters Removed)

Slot 4 connectors (2)

Slot 4 standoff

mounting

posts (2)

Standoff mounting

posts (6)

Port adapter connectors (6)

Phillips screw mounting posts (6)

Slot1

Slot2

Phillips screw

access holes (6)

Slot 4 Phillips

screw mounting

posts (2)

Slot3

68452

Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Router Installation and Verification Note

21

Image 21

Cisco Systems WS-C6513-E-RF manual Module Top View with Port Adapters Installed, Module Top View with Port Adapters Removed

Contents

Product Number WS-SVC-CMM Contents Front Panel DescriptionsCMM Module Description Color6-Port T1 and E1 Port Adapters ColorDescription Color 24-Port FXS Port AdapterDescription 6-Port T1 and E1 Port Adapters Receive Port LEDsAd-Hoc Conferencing and Transcoding Port Adapter RequirementsColor DescriptionWarning IMPORTANT SAFETY INSTRUCTIONS Safety OverviewHardware Requirements Software RequirementsWarning Ultimate disposal of this product should be handled according to all national laws and regulations. Statement Warning Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface. Statement Installing and Removing the Module Installing the ModuleRequired Tools Installing and Removing the Module Horizontal slotsSWITCH FABRIC MDL Installing and Removing the ModuleFigure 5 Positioning the Module in a Horizontal Slot Chassis Insert moduleClearing the EMI Gasket in a Horizontal Slot Chassis 1 mm Gap between the module EMI gasket and the module above itVertical slots Ejector lever fully Positioning the Module in a Vertical Slot Chassisextended EMI gasket EMI gasketPress left Press left Gap between the module EMI gasket and the module above it 1 mmEjector Lever Closure in a Vertical Slot Chassis Removing the ModuleTo remove a module from the chassis, perform these steps Horizontal slotsVertical slots Removing a Port Adapter from Module Slots 1 through Removing and Replacing Port AdaptersModule Bottom View Phillips screws installed from bottomFigure 13 Module Top View with Port Adapters Removed Figure 12 Module Top View with Port Adapters InstalledStandoffs Slot 4 PhillipsInstalling a Port Adapter in Module Slots 1 through Removing an Ad-Hoc Conferencing and Transcoding Port Adapter in Slot Page Verifying the Installation RJ-45 Port Connector and Cabling SpecificationsVerifying the Installation Figure 14 RJ-45 Port Connector Pin1RJ-45 Port Connector and Cabling Specifications DescriptionRJ-21 Port Connector and Cabling Specifications Figure 15 RJ-21 Telco Interface 90-Degree Cable ConnectorFigure 16 RJ-21 Telco Interface 180-Degree Cable Connector Connector Pin Accessing the Port Adapter PortsSignal PortConfiguring the Port Adapter Ports Configuring the Port Adapter Clock Sourceclock source line primary secondary 1..17 internal Boot/Power Management Option Disaster Recovery for Module Software UpgradesSupervisor Engine Model File Name AliasDisaster Recovery for Supervisor Engines Running Cisco IOS Software Password Recovery Password RecoveryCisco 7600 Series Router Module Installation Guide Catalyst 6500 Series Switch Module Installation GuideCatalyst 6500 Series Switch Cisco IOS Software Configuration Guide Cisco 7600 Series Router Cisco IOS Software Configuration GuideObtaining Documentation, Obtaining Support, and Security Guidelines