Manuals / Cisco Systems / Computer Equipment / Switch

Cisco Systems WS-C6513-E-RF, 6500-E manual Password Recovery

Models: 6513-E 6500-E WS-C6513-E-RF

1 34

Download 34 pages 43.44 Kb

Page 32

Password Recovery

Password Recovery

Step 3 Under the CLI Config mode, enter the tftp-server[device]:[golden-image] alias [alias-name] command to translate the filename of the downloaded file.

The [golden-image] is the file to be downloaded, and the [device] can be any flash file system on the supervisor engine. See Table 8 for configuring the appropriate [alias-name] corresponding to the supervisor engine type in use.

Step 4 Under the CLI exec mode, enter the hw-module module [mod] boot [pm_option] command to set the power management option for the CMM.

See Table 8 for configuring the appropriate [pm_option] corresponding to the supervisor engine type in use.

Step 5 Enter the hw-module module [mod] reset command to reset the module.

When the CMM powers up, disaster recovery is complete.

Step 6 After you complete the disaster recovery, under CLI config mode, enter the no tftp-server[device]:[golden-image] command to remove the filename translation.

Step 7 Set the power management option for the CMM to zero (0) by entering the command hw-module module [mod] boot config-register.

This step is necessary to prevent the download mechanism from triggering every time that the CMM is reset.

Password Recovery

Before performing the password recovery procedure, you must console into the CMM by performing these steps:

Step 1 Remove the CMM from the chassis. For removal information, see the “Removing the Module” section on page 17.

Note There are two RJ-45 ports on the CMM motherboard. The second one towards the edge or end of the motherboard is the console port.

Step 2 Connect a straight-through cable, not a regular rolled flat cable, to the console port on the motherboard.

Step 3 Remove the module directly above the CMM to allow a space for the console cable to run from the CMM motherboard to outside of the chassis.

Step 4 Reinstall the CMM into the chassis.

Step 5 Perform the recovery procedure in Password Recovery Procedure for the Catalyst 6500/6000 SeriesSwitches Running Cisco IOS System Software to recover the password for the CMM.

Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Router Installation and Verification Note

32

Image 32

Cisco Systems WS-C6513-E-RF, 6500-E manual Password Recovery

Contents

Product Number WS-SVC-CMM CMM Module ContentsFront Panel Descriptions Color DescriptionDescription 6-Port T1 and E1 Port AdaptersColor 24-Port FXS Port Adapter ColorDescription 6-Port T1 and E1 Port Adapters Receive Port LEDsRequirements Ad-Hoc Conferencing and Transcoding Port AdapterColor DescriptionSafety Overview Warning IMPORTANT SAFETY INSTRUCTIONSHardware Requirements Software RequirementsWarning Ultimate disposal of this product should be handled according to all national laws and regulations. Statement Warning Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface. Statement Required Tools Installing and Removing the ModuleInstalling the Module Horizontal slots Installing and Removing the ModuleInstalling and Removing the Module SWITCH FABRIC MDLFigure 5 Positioning the Module in a Horizontal Slot Chassis Insert module1 mm Gap between the module EMI gasket and the module above it Clearing the EMI Gasket in a Horizontal Slot ChassisVertical slots Positioning the Module in a Vertical Slot Chassis Ejector lever fullyextended EMI gasket EMI gasketGap between the module EMI gasket and the module above it 1 mm Press left Press leftRemoving the Module Ejector Lever Closure in a Vertical Slot ChassisVertical slots To remove a module from the chassis, perform these stepsHorizontal slots Removing and Replacing Port Adapters Removing a Port Adapter from Module Slots 1 throughPhillips screws installed from bottom Module Bottom ViewFigure 12 Module Top View with Port Adapters Installed Figure 13 Module Top View with Port Adapters RemovedStandoffs Slot 4 PhillipsInstalling a Port Adapter in Module Slots 1 through Removing an Ad-Hoc Conferencing and Transcoding Port Adapter in Slot Page Verifying the Installation Verifying the InstallationRJ-45 Port Connector and Cabling Specifications Pin1 Figure 14 RJ-45 Port ConnectorRJ-45 Port Connector and Cabling Specifications DescriptionFigure 16 RJ-21 Telco Interface 180-Degree Cable Connector RJ-21 Port Connector and Cabling SpecificationsFigure 15 RJ-21 Telco Interface 90-Degree Cable Connector Accessing the Port Adapter Ports Connector PinSignal Portclock source line primary secondary 1..17 internal Configuring the Port Adapter PortsConfiguring the Port Adapter Clock Source Disaster Recovery for Module Software Upgrades Boot/Power Management OptionSupervisor Engine Model File Name AliasDisaster Recovery for Supervisor Engines Running Cisco IOS Software Password Recovery Password RecoveryCatalyst 6500 Series Switch Module Installation Guide Cisco 7600 Series Router Module Installation GuideCatalyst 6500 Series Switch Cisco IOS Software Configuration Guide Cisco 7600 Series Router Cisco IOS Software Configuration GuideObtaining Documentation, Obtaining Support, and Security Guidelines