Manuals / Cisco Systems / Computer Equipment / Switch

Cisco Systems WS-C6513-E-RF, 6500-E Module Bottom View, Phillips screws installed from bottom

Models: 6513-E 6500-E WS-C6513-E-RF

1 34

Download 34 pages 43.44 Kb

Page 20

Module (Bottom View)

Removing and Replacing Port Adapters

Warning Blank faceplates and cover panels serve three important functions: they prevent exposure to hazardous voltages and currents inside the chassis; they contain electromagnetic interference (EMI) that might disrupt other equipment; and they direct the flow of cooling air through the chassis. Do not operate the system unless all cards, faceplates, front covers, and rear covers are in place. Statement 1029

Step 9 To install the module into the Catalyst 6500 series switch or the Cisco 7600 series router, see the “Installing the Module” section on page 10.

Figure 11

Module (Bottom View)

STATUSREAR MDL

6	5	4	3	2	1		6	5	4	3	2	1	6TI-X6600-WS	STATUS
						6EI-X6600-WS								X6600-WS

Phillips screws (6)

(installed from bottom)

68446

Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Router Installation and Verification Note

20

Image 20

Cisco Systems WS-C6513-E-RF, 6500-E manual Module Bottom View, Phillips screws installed from bottom

Contents

Product Number WS-SVC-CMM CMM Module ContentsFront Panel Descriptions Color DescriptionDescription 6-Port T1 and E1 Port AdaptersColor 24-Port FXS Port Adapter ColorDescription 6-Port T1 and E1 Port Adapters Receive Port LEDsRequirements Ad-Hoc Conferencing and Transcoding Port AdapterColor DescriptionSafety Overview Warning IMPORTANT SAFETY INSTRUCTIONSHardware Requirements Software RequirementsWarning Ultimate disposal of this product should be handled according to all national laws and regulations. Statement Warning Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface. Statement Required Tools Installing and Removing the ModuleInstalling the Module Horizontal slots Installing and Removing the ModuleInstalling and Removing the Module SWITCH FABRIC MDLFigure 5 Positioning the Module in a Horizontal Slot Chassis Insert module1 mm Gap between the module EMI gasket and the module above it Clearing the EMI Gasket in a Horizontal Slot ChassisVertical slots Positioning the Module in a Vertical Slot Chassis Ejector lever fullyextended EMI gasket EMI gasketGap between the module EMI gasket and the module above it 1 mm Press left Press leftRemoving the Module Ejector Lever Closure in a Vertical Slot ChassisVertical slots To remove a module from the chassis, perform these stepsHorizontal slots Removing and Replacing Port Adapters Removing a Port Adapter from Module Slots 1 throughPhillips screws installed from bottom Module Bottom ViewFigure 12 Module Top View with Port Adapters Installed Figure 13 Module Top View with Port Adapters RemovedStandoffs Slot 4 PhillipsInstalling a Port Adapter in Module Slots 1 through Removing an Ad-Hoc Conferencing and Transcoding Port Adapter in Slot Page Verifying the Installation Verifying the InstallationRJ-45 Port Connector and Cabling Specifications Pin1 Figure 14 RJ-45 Port ConnectorRJ-45 Port Connector and Cabling Specifications DescriptionFigure 16 RJ-21 Telco Interface 180-Degree Cable Connector RJ-21 Port Connector and Cabling SpecificationsFigure 15 RJ-21 Telco Interface 90-Degree Cable Connector Accessing the Port Adapter Ports Connector PinSignal Portclock source line primary secondary 1..17 internal Configuring the Port Adapter PortsConfiguring the Port Adapter Clock Source Disaster Recovery for Module Software Upgrades Boot/Power Management OptionSupervisor Engine Model File Name AliasDisaster Recovery for Supervisor Engines Running Cisco IOS Software Password Recovery Password RecoveryCatalyst 6500 Series Switch Module Installation Guide Cisco 7600 Series Router Module Installation GuideCatalyst 6500 Series Switch Cisco IOS Software Configuration Guide Cisco 7600 Series Router Cisco IOS Software Configuration GuideObtaining Documentation, Obtaining Support, and Security Guidelines