Classe Audio VSX-80TXV-S manual Minute guide, Wait for the test tones to finish then confirm

5 minute guide 02

RECEIVER	INPUT		SYSTEM OFF
			SOURCE
	SELECT
AV PRE-PROGRAMMED AND LEARNING
REMOTECONTROLUNIT
		DVR 2
DVD	TV	DVR1	TVCTRL
		XM RADIO	ROOM 2
CD	CD-R	TUNER	RECEIVER

	DIALOG E	PHASE		S.RETRIEVER
D.ACCESS +10				CLASS DISC
				ENTER
TOPMENU				MENU
	TUNE
DTVMENU	ST		ST	T.EDIT
SETUP	ENTER			RETURN
GUIDE CATEGORY TUNE			BAND
	TV CONTROL
TVVOL	INPUT	TVCH		VOL
	SELECT

7 Wait for the test tones to finish then confirm the

speaker configuration in the OSD.

A progress report is displayed on-screen while the

receiver outputs test tones to determine the speakers

present in your setup. Try to be as quiet as possible while

it’s doing this.4

• With error messages (such as Ambient Noise or

Microphone Check) select RETRY after checking for

ambient noise (see Problems when using the Auto

1Switch on the receiver and your TV.

2Connect the microphone to the MCACC SETUP MIC jack on the front panel.

Place the microphone so that it’s about ear level at your normal listening position (use a tripod if possible). Make sure there are no obstacles between the speakers and the microphone.

•Push down on the PUSH OPEN tab to access the MCACC SETUP MIC jack:

S-VIDEO		VIDEO/GAME INPUT		MCACC
	VIDEO	L AUDIO R	DIGITAL IN	SETUP MIC

PHONES	SYSTEM			TUNING/	TUNER
	SETUP	RETURN	TONE	STATION	EDIT	SPEAKERS
			MULTI JOG

3Press RECEIVER on the remote, then press SETUP. An on-screen display (OSD) appears on your TV. Use the buttons and ENTER to navigate through the

screens and select menu items. Press RETURN to exit the current menu. Press SETUP at any time to cancel.1

4Select ‘Auto MCACC’ from the System Setup menu then press ENTER.2

System Setup				2. Auto MCACC
	1.Surr	Back System		Surr Back System			]
	2.Auto	MCACC			Normal (SB)
	3.Manual		MCACC
	4.Manual		SP Setup
	5.Input	Assign
	6.Other	Setup
			: Exit	Enter : Start		: Cancel

5Make sure ‘Normal (SB)’ is selected then press ENTER.3

6Follow the instructions on-screen.

Make sure the microphone is connected, and if you’re using a subwoofer, make sure it is switched on and set to a comfortable volume level.

Note

MCACC Setup below) and verifying the mic

connection. If there doesn’t seem to be a problem,

you can simply select OK and continue.

2.Auto MCACC		2.Auto MCACC
Now Analyzing			Check!
		Front	[ YES ]
Environment Check
		Center	[ YES ]
Ambient Noise	[ OK ]	Surround	[ YES ]
Microphone	[ OK ]	SB	[ Yx2 ]
Speaker YES/NO	[ OK ]	SUB W.	[ YES ]
	:Cancel			OK
				:Cancel

The configuration shown on-screen should reflect the actual speakers you have.5

If you see an error message (ERR) in the right side column (or the speaker configuration displayed isn’t correct), there may be a problem with the speaker connection. If selecting RETRY doesn’t work, turn off the power and check the speaker connections. If there doesn’t seem to be a problem, you can simply use

to select the speaker and to change the setting (and number for surround back) and continue.

8Make sure ‘OK’ is selected, then press ENTER. A progress report is displayed on-screen while the receiver outputs more test tones to determine the optimum receiver settings for channel level, speaker distance, and Acoustic Calibration EQ.

Again, try to be as quiet as possible while this is happening. It may take 3 to 8 minutes.

9The Auto MCACC Setup has finished! Select ‘SKIP’ to go back to the System Setup menu.

The settings made in the Auto MCACC Setup should give you excellent surround sound from your system, but it is also possible to adjust these settings manually using the System Setup menu (starting on page 33).6

1• If you cancel the Auto MCACC Setup, or leave an error message for over three minutes, the screen saver will appear.

•The OSD will not appear if you have connected using the HDMI output to your TV. Use component, S-video, or composite connections for system setup.

2You can’t use the System Setup menu when the XM Radio input source is selected (in either the main or sub room).

3• If you are planning on bi-amping your front speakers, or setting up a separate speaker system in another room, read through Surround back speaker setting on page 33 and make sure to connect your speakers as necessary before continuing to step 6.

•If you have THX-certified speakers, make sure YES is selected in THX Speaker Setup on page 40.

4Do not adjust the volume during the test tones. This may result in incorrect speaker settings.

5If you’re using the front panel display, the diagram in Listening to Surround Sound above indicates (in bold) how each speaker is displayed.

6• Depending on the characteristics of your room, sometimes identical speakers with cone sizes of around 5 inches will end up with different size settings. You can correct the setting manually using the Manual speaker setup on page 37.

•The subwoofer distance setting may be farther than the actual distance from the listening position. This setting should be accurate (taking delay and room characteristics into account) and generally does not need to be changed.

9

En