Cobra Electronics AN - 8630 - 25 manual Battery Back Up, Location, Set The Clock, Charging, Ringer

	SOME THINGS YOU NEED TO					GETTING SET UP...
	KNOW BEFORE YOU GET STARTED					IT’S AS EASY AS 1-2-3
	Now that your new Cobra Intenna Cordless					3	Battery Back Up
	Phone Answering System is out of the box						Now‘s the time to put your 9v back-up
	and ready to use, here are some things					BACK UP	battery (included) into the base. Simply
			Cobra			BATTERY
	you’ll need to be aware of before getting						open the battery compartment located
	started.						below the handset on the base, plug-in
1	Location						the battery, and your outgoing and
							incoming messages will be saved
	Be sure the location you‘ve chosen is near
							during power outages or other
	both an electrical outlet and a telephone
							disconnections.
	wall jack—both are required to connect your
2					10
	new Cobra Telephone Answering System.						Set The Clock
						5
	Maximum range is obtained by locating the						Press and hold the button that says
	base as high as possible in your home.		5	9		CLOCK
							”Clock” and VOICE HELP will direct you
						BUTTON
	Charging					6	to press the “SKIP”▼▼ button until you
	After connecting, and before using the
					6		hear the correct day of the week, then
	handset of your new system, it will need to					SKIP	release. Press and release ”Clock” again,
						BUTTON
	rest in the base overnight (at least 12 hours)		REPEAT		SKIP		then SKIP or REPEAT▼▼button until the
4	in order to charge.		7			7	correct hour is displayed in the LED
		Ringer				BUTTONREPEAT	window. Repeat again for the minutes.
	1	Make sure the RINGER switch, located					Press ”Clock” again and VOICE HELP will
	RINGER	on the rear of the base, is set to ON.					verify the time that has been set. Every
		Pulse/Tone					message received will then be identified
	2						by day of the week and time.
		Set the PULSE/TONE switch, located					Record your
	TONE	on the rear of the base, to the operation
	PULSE/						outgoing message
		that is correct for your installation.				8
							Check to be sure the ICM (Incoming
						ICM
							Message) Recording switch on the side of
		Plug it in				RECORDING
	4					SWITCH	the phone is set at “2 Min.” (as opposed
		Plug the adapter cord into the power jack					to “Annc Only”). Press and hold the
3		on the rear of the base, then plug the	8			9	button that says “OGM” (Outgoing
		adapter into any standard 110V outlet.					Message) and VOICE HELP will direct you
		(VOICE HELP will direct you to set clock				BUTTON	to start recording your message after the
						OGM
		and outgoing message). Set the handset					beep. The LED display window will
		on the base to charge and in 12 hours				10	indicate the length in seconds; you have
		you’re ready to make and receive calls.				LED DISPLAY	up to 60 seconds recording time for your
		The Answering System will work while					OGM. Speak about 6 inches from the
		the telephone handset is charging.					microphone located in small slot on front
	Keep This Guide						of base. Release the button and your
							message plays back. Not satisfied with
	Put this guide in a handy place. You may
							your message? Simply follow these steps
	want to refer to it for information when
							over again and keep recording your
	using or programming different features of
							outgoing message until you’re
	your Cobra Intenna Cordless Telephone
							comfortable.
	Answering System.
Cobra®						NEED HELP?		1-773-889-3087
AN8630-25