PROBLEM | CAUSE | SOLUTION |
Fuses or circuit breakers open frequently.
Saw vibrates excessively.
Start switch does not operate.
1.Motor is overloaded.
2.Fuses or circuit breakers are wrong size or defective.
3.Dull blade.
4.Start switch is defective.
1.Blade is warped.
2.Belt is damaged.
3.Saw is not mounted securely.
4.Work surface is uneven.
1. Switch contacts are burned out.
1.Feed work more slowly.
2.Replace fuses or circuit break- ers.
3.Replace the blade.
4.Have the switch replaced.
1.Replace the blade.
2.Replace the belt.
3.Tighten all hardware.
4.Reposition on a flat surface. Ad- just the leveling feet on legs.
1.Have the switch replaced and re- quest a voltage check from the power company.
| 2. | Capacitor | is defective |
|
| 2. | Have | the capacitor | replaced. |
| |||||||
| 3. | Connections | are loose or dam- | 3. | Have | the wiring | checked and re- | ||||||||||
|
| aged. |
|
|
|
|
|
|
| paired. |
|
|
|
|
|
| |
Handwheels are hard to turn. | 1. | Sawdust | has collected | on | the | 1. | Clean and lubricate | the mecha- | |||||||||
|
| mechanism | inside saw. |
|
|
| nism. |
|
|
|
|
|
| ||||
Blade does not lower when turning | 1. | Blade | lock | handle | is | not | fully | 1. | Fully | release | the | blade | lock | ||||
height handwheel. |
| released, |
|
|
|
|
|
| handle. |
|
|
|
|
|
| ||
Miter gage does not move smoothly. | 1. | Miter | gage | assembly is dirty or | 1. | Release | the miter gage | knob and | |||||||||
|
| sticky, |
|
|
|
|
|
|
| wax | the | miter | gage | base | and | ||
|
|
|
|
|
|
|
|
|
| sides. |
|
|
|
|
|
| |
Cut binds, burns or stalls motor when | 1. | Blade | or teeth are dull. |
|
| 1. | Sharpen | or replace | the blade. | ||||||||
ripping. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 2. | Blade | is heeling. |
|
|
| 2. | See Heeling | the Sawblade in the | ||||||||
|
|
|
|
|
|
|
|
|
| Adjustments | section. |
|
| ||||
| 3. | Board | is warped. |
|
|
| 3. | Replace | the board. |
|
|
| |||||
| 4. | Ripfencedoesnotparallelblade. |
| 4. | See Aligning | the Rip Fence in the | |||||||||||
|
|
|
|
|
|
|
|
|
| Assembly | section. |
|
|
| |||
Saw blade does not cut true at 90°or | 1. | Indicators | are not | properly | ad- | 1. | See | Setting | the Bevel | Stops | and | ||||||
45° positions. |
| justed. |
|
|
|
|
|
|
| Indicator | in the Adjustments | sec- | |||||
|
|
|
|
|
|
|
|
|
| tion. |
|
|
|
|
|
|
|
| 2. | Positive stops inside base are | 2. | See | Setting | the Bevel | Stops | and | |||||||||
|
| not accurate. |
|
|
|
| Indicator | in the Adjustments | sec- | ||||||||
|
|
|
|
|
|
|
|
|
| tion. |
|
|
|
|
|
|
|
45 | rRRFTSMRN TABLE SAW 315.228390 |
