Craftsman 315.22839 owner manual Removing, Replacing The Throat, Throatplate

Models: 315.22839

1 66

Page 34

REMOVING	/	REPLACING THE THROAT	THROATPLATE
PLATE
See Figure	44.		KEY 8LOT_
,_k WARNING:		Make sure the switch is off, the

switch key is removed, and your saw is unplugged. Failure to do so could result in accidental starting, resulting in serious personal injury.

•To remove the throat plate, first loosen the screw in the throat plate with a phillips screwdriver and lift the front end. Pull it out toward the front of the saw.

•To re-install the throat plate, place it in the opening. Push it toward the rear of saw base to engage the spring clip.

Note: The keyslot in the throat plate will drop over the screw.

•Check that the throat plate is even with the table top. If not, adjust the four set screws with a 2 mm hex key. See the procedure in the Assem- bly section.

•Securely tighten throat plate screw. Do not allow the throat plate to bow up above the table surface.

SPRINGCLIP

TABLE

TOP

Fig. 44

CRRFTSMRN° TABLESAW 315.22839034

Page 34

Image 34

Craftsman 315.22839 owner manual Removing, Replacing The Throat, Throatplate

Contents

IIRRFrSMRN Safety Features Assembly Operation Maintenance Parts ListModel No OwnersManualLabels UnpackingCRRFTSMRN TABLE SAW 32-33 30-3431-32 CheckHeelingParallelingof theSawBladetotheMiterGageGrooveMEANING SYMBOLREAD ALL INSTRUCTIONS RULES FOR SAFE OPERATION Continued DO NOT OVERREACH. Keep proper footing and balance at all timesSAVE THESE INSTRUCTIONS RULES FOR SAFE OPERATION ContinuedGROUNDING INSTRUCTIONS GROUNDING PIN COVER OF GROUNDEDrRRFTSMRH TABLESAW315.228390 connected to power supply when you are assemble all parts to your saw before connectingit to power supply. Saw should never be assembling parts, making adjustments, installingGI J CRRFTSMRNTABLESAW315.22839010flatwasher#10 screw#10-24x 1/2inF. Hardwarefor Handwheel screw headrRAFTSMANTABLE SAW WRENHES8 ram,10 ram,and 12 mm FRAMINGSQUARE NUTDRIVERand 6 mm COMBINATIONSQUARE HAMMER 45TRIANGLE 13rRRFrSMRN*TABLESAW315.228390REPLACEMENT 10 inch Table SawWARNING I WHEN SERVICING, USE ONLY B D A AWhen Mounting an Auxiliary IorDo ExtensionNotLiftSawTablesWith. RailsAssembly Before Operating this Saw Read Owners IIRRFTSMRNIANTI-KICKBACK PAWLS EXTENSION FRONT MITERRAIL GAGE BEVELSWITCH HANDWHEELWITH KEYKNOW YOUR TABLE SAW REARRAILOVERVIEW HANDWHEEL INSTALLING HANDWHEELS ON TABLE SAW BASEBEVEL HANDWHEEL HEIGHT UPPERBRACEWASHER HEXNUTMOUNTING THE LEG STAND ON THE TABLE SAW BASE ASSEMBLING LEG STAND Continued19rIRFTSMRNTABLESAW315.228390 HEXNUT EXTENSIONHEX HEADBOLT FLAT BLOCKTABLE OF WOOD EXTENSION BLOCK FRONT OFFRONT OF OF WOODREARRAIL operatingposition INSTALLINGTHEREARRAILCONNECTOR REARRAILFRONT RAIL CONNECTORHE BOLT8 ENDCAPASSEMBLY TO INSTALLSCALE INDICATOR ALIGNING THE RIP FENCE AND FRONT RAILCHECKING THE THROAT PLATE INSTALLING THE BELT AND BELT GUARD See Figures 20 andBELT BELTGUARD HEXKEYFRAMINGSQUARE THROATPLATEBLADE INSTALLINGWASHER BLADE GUARD BRACKET LOCKRIVINGKNIFE THROAT PLATE FRAMING RIVINGKNIFE BLADERIVINGKNIFE BLADE BLADE JMITER GAGE GROOVE Illll Jt*l lfllllFRAMING SQUARE MITER GAGE GROOVERIP FENCE FRAMING ALIGNMENTMITER GAGE GROOVE BLADE MITER GAGE GROOVE RIP FENCE FRAMINGo,/o Io oo o Io o CHECKING SQUARENESS OF EXTENSION TABLES TO SAW TABLEBLADE BLAIWASHER REPLACING THE BLADEBLADE GUARD TO LOOSEN BLADE NUT BLADE NUT BLADE ARBOR BHAFTFRAMING G FRAMINGBLADEGUARD18NOTSHOWNFORCLARITY AT FRONTFRONT j SETTING THE BEVEL STOPS AND INDICATORSAWTABLEVIEW FROMBELOW REARSAW TABLE TABLEBRACKET FRONTMITERKNOB GAGE ROD MITER INDICATORADJUSTING THE MITER GAGE 8CALEREPLACING THE THROAT REMOVINGTHROATPLATE PUSHSTICK8 AVOIDING KICKBACK35rRRFI$MRNTABLESAW315.228390 TYPES OF CUTS MITERGAGEHEREPLACERIGHTHANDON MITERGAGEKNOBHERE PLACELEFTHANDONWHENMITERGAGE18MAKING A RIP CUT MITER CUT RIP CUTMAKING A MITER CUT BLADEBLADERIP FENCE ANGLEDONRIGHT BEVELCROSSCUT BLADEANGLED BEVELLOCK HANDLE NOTSHOWNON RIGHT81DEOF BLADE COMPOUNDBEVEL MITERCUT WHENMITERGAGE18 PLACERIGHTHANDPLACELEFTHANDON MITERGAGEHERE MITERGAGEKNOBHERE LARGEPANELCUT RIP FENCE MAKING A LARGE PANEL CUTMAKING A NON-THROUGH CUT HANDWHEELDADOCUT MAKING A DADO CUTIRRFI$MRN* TABLESAW FRONTOF SAW GENERAL MAINTENANCErIIFTSMIINTABLESAW315.228390 SOLUTION PROBLEMCAUSE Assembly PROBLEMSOLUTION CAUSEand Front Rail in the Assembly PROBLEMSOLUTION CAUSE£RRFTSMRN TABLE SAW FIGURE A CRAFTSMANTABLE SAW - MODEL rRRFTSMRNTABLESAW315.22839048TABLE SAW - MODEL PARTS LIST FOR FIGURE ACRAFTSMAN NO. NUMBERCRAFTSMAN TABLE SAW- MODEL NO FIGUREBMODEL NO PARTS LIST FOR FIGURE BCRAFTSMAN TABLE SAW QUANFIGUREC CRAFTSMAN TABLE SAW - MODEL NO2517 IO 131 OrMODEL NO PARTS LIST FOR FIGURE CCRAFTSMAN TABLE SAW KEY PART NO. NUMBERCRAFTSMAN TABLE SAW- MODEL NO FIGUREDCRAFTSMAN TABLE SAW- MODEL NO PARTS LIST FOR FIGURE DQUAN MODEL NO CRAFTSMAN TABLE SAWFIGUREE QUAN PARTS LIST FOR FIGURE ECRAFTSMAN TABLE SAW- MODEL NO PlateMODEL NO CRAFTSMAN TABLE SAWFIGUREF MODEL NO PARTS LIST FOR FIGURE FCRAFTSMAN TABLE SAW QUANMODEL NO CRAFTSMAN TABLE SAWFIGUREG CRAFTSMAN TABLE SAW- MODEL NO PARTS LIST FOR FIGURE GQUAN MODEL NO CRAFTSMAN TABLE SAWFIGUREH CRAFTSMAN TABLE SAW - MODEL NO PARTS LIST FOR FIGURE HQUAN MODEL NO CRAFTSMAN TABLE SAWFIGUREI MODEL NO PARTS LIST FOR FIGURECRAFTSMAN TABLE SAW NO. NUMBER1-877-LE-FOYER Au Canadapourserviceen franaisy paraordenarpiezascon entregaa domicilio 1-888-SU-HOGAR sM