Blades, Screwdriver, Square, Clamps | Craftsman 315.28462 specs

BLADES				A WARNING:
For maximum		performance, it is recommended	that you	A WARNING:		Do not use blades rated	less than	the
use the 36-tooth, 10 in. carbide-tipped combination blade				speed	of this	tool. Failure to heed this	warning	could
provided	with	your saw. Additional blade styles	of the	result	in personal injury.
same high quality are available for specific operations
such as ripping. Your local dealer can provide you with
complete	information.

Kerf width must be within the limits stamped on the spreader/riving knife.

_The following tools (not included or drawn to scale) are needed for assembly and making adjustments:

SCREWDRIVER

COMBiNATiON

SQUARE

U AND10mmSOCKET

C-CLAMPS

Fig. 4

Page 13

Image 13

Craftsman 315.28462 manual Blades, Screwdriver, Square, Clamps

Contents

Perators Manual Craftsman ONE Year Full Warranty Read ALL Instructions Bladecoastsafter Being Turned OFF Before Making a CUT, be Sure ALL ADJUST= Ments are SecureRemove ALL Fences and Auxiliary Tables Always USE Blade GUARD, SPREADER, Hold the Workpiece Firmly Against the Table NEVERstandorhaveanypartofyourbodyin linePage Service Symbol SignalYour nearest Authorized Service Center for repair LCAUTION Extension Cords Speed and WiringCord Length Electrical Connection Featherboard Cutterhead planers and jointer planersGum Ripping or Rip Cut Productspecifications See Figure Knowyourtablesaw Operatingcomponents Switchin LOCKEDPOSiTiON Screwdriver BladesScrewdriver Square Thefollowingitemsareincludedwithyourtablesaw Mounting Holes UnpackingTo Assemble the LEG Stand See Figures 6 Slot Mounting the Table SAW Base to INDiCATORHolelocking Knob Plate To REMOVE/REPLACETHETHROATPLATE See Figures 13 Blade WrenchPawl ANTI-KICKBACK Pawls Blade Guard Lever Correct Verticaladjustment SET Screw SpreaderSpreader Rivingknife See Figures 17 To Assemble the Sliding Table AssemlbyRear Screw Extensionrod Dust BAG DustSee Figures 20 Push Basic Operation of the Table SAW ApplicationsCauses of Kickback Avoiding Kickback Cuttingaids HOW to Make a JIG for RIP Cutting Narrow WorkpiecePush Blocks Auxiliary Fence Stop JIG Handle Featherboard HOW to Mount a FeatherboardHowto Makea Featherboard Push Push Crosscut Bevelmitercut Typesofcuts Gullet To ChangebladedepthLocking Lever Bevel Blade Clamp Locking Lever To USE the RIP FenceFence Front Locking Scalelever Miter Gauge Lock See Figures 36 Heelingparalleling the Blade to Switchin Lockedposition Switchswitch OnoffTo Make a Cross CUT See Figures 39 Making a Miter CUT Making a RIP CUTMiter CUT Blade Straight Miter Gauge Angled See Figures 43 Makinga BevelcrosscutBevelcrosscut Miter Gauge Bladeangled Blade Angled Scale Making a Compound Bevel Miter CUT BEVELRiP CUT RiP FenceCompoundbevelmiter CUT Placelefthandon Miter Makinga Large Panel CUT HEIGHT/BEVEL Adjusting HandwheelMaking a NON-THROUGH CUT Largepanelcut Removed BladeguardStick Making a Dado CUT Dadocut Arborblade See Figures 50Throat Plate Blade Wrench Gaugebase Miter Gaugerod Adjustable To Adjust the Miter GaugeLock 0 Adjustable Oadjustment Screw To Check Alignment of the RIP Locking Lever General MaintenanceFence to Blade Bolts Solution ProblemCause Problem 10 in. Table SAW Model Number Craftsman Description KEY Part NO, NumberQTY KEY Part NO. Number Figure B Description QTY Parts List for Figure B Figure C Craftsman 10 in. Table SAW Model Number Parts List for Figure C Figure D KEY Part NO. Number Description DESCRiPTiON KEY Part NO. Number Number KEY Part Number Description QTY Parts List for Figure FPage @anag@

BLADES

SCREWDRIVER

SCREWDRIVER

SQUARE

C-CLAMPS