Dust BAG, See Figures 20, Push | Craftsman 315.28462 instruction

TO INSTALL DUST BAG

See Figure 19.

[] Slide the elbow inside the dust chute on the back of the table saw.

NOTE: For efficient operation, empty the dust bag before it is half full. This will permit better air flow through the bag.

BLADE

WRENCHES

DUST

ELBOW

DUST

BAG

Fig. 19

TO STORE THE TABLE SAW ACCESSORIES

See Figures 20 - 21.

The table saw has two convenient storage areas (one on either side of the saw cabinet) specifically designed for the saw'saccessories.

When not in use, store the accessories securely by snap- ping each accessory in place.

Fig. 20

PUSH

STICK

MITER

GAUGE

STORAGE

HOOK

RiP

FENCE

Fig. 21

Page 21

Image 21

Craftsman 315.28462 manual Dust BAG, See Figures 20, Push, Miter Gauge Storage Hook

Contents

Perators Manual Craftsman ONE Year Full Warranty Read ALL Instructions Bladecoastsafter Being Turned OFF Before Making a CUT, be Sure ALL ADJUST= Ments are SecureRemove ALL Fences and Auxiliary Tables Always USE Blade GUARD, SPREADER, Hold the Workpiece Firmly Against the Table NEVERstandorhaveanypartofyourbodyin linePage Service Symbol SignalYour nearest Authorized Service Center for repair LCAUTION Extension Cords Speed and WiringCord Length Electrical Connection Featherboard Cutterhead planers and jointer planersGum Ripping or Rip Cut Productspecifications See Figure Knowyourtablesaw Operatingcomponents Switchin LOCKEDPOSiTiON Screwdriver BladesScrewdriver Square Thefollowingitemsareincludedwithyourtablesaw Mounting Holes UnpackingTo Assemble the LEG Stand See Figures 6 INDiCATOR Slot Mounting the Table SAW Base toHolelocking Knob Plate To REMOVE/REPLACETHETHROATPLATE See Figures 13 Blade WrenchPawl ANTI-KICKBACK Pawls Blade Guard Lever Verticaladjustment SET Screw Spreader CorrectSpreader Rivingknife See Figures 17 To Assemble the Sliding Table AssemlbyRear Screw Extensionrod Dust BAG DustSee Figures 20 Push Basic Operation of the Table SAW ApplicationsCauses of Kickback Avoiding Kickback Cuttingaids HOW to Make a JIG for RIP Cutting Narrow WorkpiecePush Blocks Auxiliary Fence Stop JIG Handle Featherboard HOW to Mount a FeatherboardHowto Makea Featherboard Push Push Crosscut Bevelmitercut Typesofcuts Gullet To ChangebladedepthLocking Lever Bevel Blade Clamp Locking Lever To USE the RIP FenceFence Front Locking Scalelever Miter Gauge Lock See Figures 36 Heelingparalleling the Blade to Switchin Lockedposition Switchswitch OnoffTo Make a Cross CUT See Figures 39 Making a Miter CUT Making a RIP CUTMiter CUT Blade Straight Miter Gauge Angled See Figures 43 Makinga BevelcrosscutBevelcrosscut Miter Gauge Bladeangled Blade Angled Scale Making a Compound Bevel Miter CUT BEVELRiP CUT RiP FenceCompoundbevelmiter CUT Placelefthandon Miter Makinga Large Panel CUT HEIGHT/BEVEL Adjusting HandwheelMaking a NON-THROUGH CUT Largepanelcut Removed BladeguardStick Making a Dado CUT Dadocut See Figures 50 ArborbladeThroat Plate Blade Wrench Gaugebase Miter Gaugerod Adjustable To Adjust the Miter GaugeLock 0 Adjustable Oadjustment Screw To Check Alignment of the RIP Locking Lever General MaintenanceFence to Blade Bolts Problem SolutionCause Problem 10 in. Table SAW Model Number Craftsman Description KEY Part NO, NumberQTY KEY Part NO. Number Figure B Description QTY Parts List for Figure B Figure C Craftsman 10 in. Table SAW Model Number Parts List for Figure C Figure D KEY Part NO. Number Description DESCRiPTiON KEY Part NO. Number Number KEY Part Number Description QTY Parts List for Figure FPage @anag@