Craftsman 315.28462 Bladecoastsafter Being Turned OFF, Remove ALL Fences and Auxiliary Tables

[] BLADECOASTSAFTER BEING TURNED OFF.

[] NEVER USE iN AN EXPLOSIVE ATMOSPHERE.

Normal sparking of the motor could ignite fumes.

[] INSPECT TOOL CORDS PERIODICALLY. If damaged, have repaired by a qualified service technician at

an authorized service facility. The conductor with insulation having an outer surface that is green with or without yellow stripes is the equipment-ground- ing conductor. If repair or replacement of the electric cord or plug is necessary, do not connect the equip- ment-grounding conductor to a live terminal. Repair or replace a damaged or worn cord immediately. Stay constantly aware of cord location and keep it well away from the rotating blade.

[] INSPECT EXTENSION CORDS PERIODICALLY and

replace if damaged.

[] GROUND ALL TOOLS. If tool is equipped with three- prong plug, it should be plugged into a three-hole electrical receptacle.

[] CHECK WITH A QUALIFIED ELECTRICIAN or service

personnel if the grounding instructions are not com- pletely understood or if in doubt as to whether the tool is properly grounded.

[] USE ONLY CORRECT ELECTRICAL DEVICES: 3-wire extension cords that have 3-prong grounding plugs and 3-pole receptacles that accept the tool's plug.

[] DO NOT MODIFY the plug provided. If it will not fit the

outlet, have the proper outlet installed by a qualified electrician.

[] KEEP TOOL DRY, CLEAN, AND FREE FROM OiL AND GREASE. Always use a clean cloth when clean- ing. Never use brake fluids, gasoline, petroleum-based products, or any solvents to clean tool.

[] FIRMLY BOLT THE SAW TO A WORK BENCH OR LEG STAND at approximately hip height.

[] NEVER OPERATE THE SAW ON THE FLOOR.

[] GUARD AGAINST KICKBACK. Kickback occurs when the blade stalls rapidly and workpiece is driven back towards the operator. It can pull your hand into the blade resulting in serious personal injury. Stay out

of blade path and turn switch off immediately if blade binds or stalls.

[] USE RiP FENCE. Always use a fence or straight edge guide when ripping.

[] SUPPORT LARGE PANELS. To minimize risk of blade pinching and kickback, always support large panels.

[] REMOVE ALL FENCES AND AUXILIARY TABLES

before transporting saw. Failure to do so can result in an accident causing possible serious personal injury.

[] STAY ALERT AND EXERCISE CONTROL. Watch what you are doing and use common sense. Do not operate tool when you are tired. Do not rush.

[] DO NOT USE TOOL IF SWITCH DOES NOT TURN IT ON AND OFF. Have defective switches replaced by an authorized service center.

[] USE ONLY CORRECT BLADES. Do not use blades with incorrect size holes. Never use blade washers or blade bolts that are defective or incorrect. The maxi- mum blade capacity of your saw is 10 in. (254 mm).

[] BEFORE MAKING A CUT, BE SURE ALL ADJUST= MENTS ARE SECURE.

[] BE SURE BLADE PATH IS FREE OF NAILS. Inspect for and remove all nails from lumber before cutting.

[] NEVER TOUCH BLADE or other moving parts during

use.

[] NEVER START A TOOL WHEN ANY ROTATING COM=

PONENT IS IN CONTACT WITH THE WORKPIECE. [] DO NOT OPERATE A TOOL WHILE UNDER THE

INFLUENCE OF DRUGS, ALCOHOL, OR ANY

MEDICATION.

[] WHEN SERVICING use only identical replacement parts. Use of any other parts may create a hazard or cause product damage.

[] USE ONLY RECOMMENDED ACCESSORIES listed in this manual or addendums. Use of accessories that are not listed may cause the risk of personal injury. Instructions for safe use of accessories are included with the accessory.

[] DOUBLE CHECK ALL SETUPS. Make sure blade is tight and not making contact with saw or workpiece before connecting to power supply.

[] ALWAYS USE BLADE GUARD, SPREADER, AND

ANTI=KICKBACK PAWLS on all "through-sawing" operations. Through-sawing operations are those in which the blade cuts completely through the workpiece as in ripping or cross cutting. Keep the blade guard down, the anti-kickback pawls down, and the spreader in place.

[] ALWAYS SECURE WORK firmly against the rip fence or miter gauge. NEVER use the rip fence during the same operation as the miter gauge.

[] WHEN MAKING NON=THROUGH RiP CUTS, always use a push stick, push block, and/or featherboard so your hands do not come within 3 inches of the saw blade.

[] WHEN RiPPiNG NARROW STOCK, always use a push stick, push block, or featherboard.