To Changebladedepth, Gullet, Locking Lever | Craftsman 315.28462

TO CHANGEBLADEDEPTH

See Figure 28.

The blade depth should be set so that the outer points of the blade are higher than the workpiece by approximately 1/8 in. to 1/4 in. but the lowest points (gullets) are below the top surface.

[] Raise the blade by turning the height/bevel adjusting handwheel clockwise or lower it by turning the hand- wheel counterclockwise.

GULLET

Fig. 28

TO CHANGE BLADE ANGLE (BEVEL)

See Figured 29 - 30.

NOTE: A 90° cut has a 0° bevel and a 45° cut has a 45 ° bevel.

[] Loosen bevel control by pulling the bevel locking lever all the way to the right.

[] Adjust the bevel angle by pushing the wheel in toward the saw then turning it. Turning the wheel counter- clockwise increases the angle of the blade, bringing it closer to 45°. Turning it clockwise decreases the angle, bringing the blade closer to 90°.

[] Tighten bevel control by pushing the bevel lock lever to the left.

TO ADJUST THE BEVEL INDICATOR

See Figure 30.

If the bevel indicator is not at zero when the saw blade

is at 90°, adjust the indicator by loosening the screw and setting it at 0° on the bevel scale. Retighten the screw.

LJ

BEVEL

LOCKING

LEVER

HEIGHT/BEVEL

ADJUSTINGSCREW HANDWHEEL

BEVEL

INDICATOR

ANGLE

ODECREASE

ANGLE

Fig. 29

Fig. 30

26

Image 26

Craftsman 315.28462 manual To Changebladedepth, Gullet, Locking Lever, Bevel, Angle

Contents

Perators Manual Craftsman ONE Year Full Warranty Read ALL Instructions Remove ALL Fences and Auxiliary Tables Before Making a CUT, be Sure ALL ADJUST= Ments are SecureBladecoastsafter Being Turned OFF Always USE Blade GUARD, SPREADER, NEVERstandorhaveanypartofyourbodyin line Hold the Workpiece Firmly Against the TablePage Your nearest Authorized Service Center for repair Symbol SignalService LCAUTION Cord Length Speed and WiringExtension Cords Electrical Connection Gum Cutterhead planers and jointer planersFeatherboard Ripping or Rip Cut Productspecifications Knowyourtablesaw See Figure Switchin LOCKEDPOSiTiON Operatingcomponents Screwdriver BladesScrewdriver Square Thefollowingitemsareincludedwithyourtablesaw To Assemble the LEG Stand UnpackingMounting Holes See Figures 6 Holelocking Knob INDiCATORSlot Mounting the Table SAW Base to To REMOVE/REPLACETHETHROATPLATE Plate Pawl Blade WrenchSee Figures 13 ANTI-KICKBACK Pawls Blade Guard Lever Spreader Rivingknife Verticaladjustment SET Screw SpreaderCorrect Rear To Assemble the Sliding Table AssemlbySee Figures 17 Screw Extensionrod See Figures 20 DustDust BAG Push Causes of Kickback ApplicationsBasic Operation of the Table SAW Avoiding Kickback Push Blocks Auxiliary Fence HOW to Make a JIG for RIP Cutting Narrow WorkpieceCuttingaids Stop JIG Handle Howto Makea Featherboard HOW to Mount a FeatherboardFeatherboard Push Push Typesofcuts Crosscut Bevelmitercut Locking Lever To ChangebladedepthGullet Bevel Fence Front To USE the RIP FenceBlade Clamp Locking Lever Locking Scalelever Lock Miter Gauge Heelingparalleling the Blade to See Figures 36 To Make a Cross CUT Switchswitch OnoffSwitchin Lockedposition See Figures 39 Miter CUT Blade Straight Making a RIP CUTMaking a Miter CUT Miter Gauge Angled Bevelcrosscut Miter Gauge Makinga BevelcrosscutSee Figures 43 Bladeangled Compoundbevelmiter CUT BEVELRiP CUT RiP FenceBlade Angled Scale Making a Compound Bevel Miter CUT Placelefthandon Miter Making a NON-THROUGH CUT HEIGHT/BEVEL Adjusting HandwheelMakinga Large Panel CUT Largepanelcut Stick Making a Dado CUT BladeguardRemoved Dadocut Throat Plate Blade Wrench See Figures 50Arborblade Lock 0 Adjustable To Adjust the Miter GaugeGaugebase Miter Gaugerod Adjustable Oadjustment Screw Fence to Blade Locking Lever General MaintenanceTo Check Alignment of the RIP Bolts Cause ProblemSolution Problem Craftsman 10 in. Table SAW Model Number QTY KEY Part NO, NumberDescription KEY Part NO. Number Figure B Parts List for Figure B Description QTY Figure C Parts List for Figure C Craftsman 10 in. Table SAW Model Number Figure D DESCRiPTiON KEY Part NO. Number Description Number KEY Part NO. Number Parts List for Figure F KEY Part Number Description QTYPage @anag@