Manuals / Brands / Computer Equipment / Network Card / CyberData / Computer Equipment / Network Card

CyberData VoIP Intercom HOLE PLUG, CONDUIT, CONDUIT, Not to Exceed 0.1, stop nut, outlet box plug, Figure A-3.Pipe Restrictions, Figure A-2.Mounting the VoIP Intercom Assembly

1 48

Download 48 pages, 2.89 Mb

Mount the Intercom

If the thread on the conduit is longer than 3/8 inch, then a stop nut (not supplied) is required. Otherwise, use the outlet box plug to plug the exit hole.

Figure A-2. Mounting the VoIP Intercom Assembly

HOLE PLUG

CONDUIT

Figure A-3shows the restrictions of the pipe going into the box.

Figure A-3. Pipe Restrictions

Not to Exceed 0.1" CONDUIT

CyberData Corporation

930181B

Operations Guide

Contents

Part #010935 PoE VoIP Intercom Operations Guide 930181B Part # COPYRIGHT NOTICE: © 2008, CyberData Corporation, ALL RIGHTS RESERVED Important Safety Instructions Pictorial Alert Icons Hazard Levels Revision History Page Contents Chapter 1 Product Overview Chapter 2 Installing the VoIP Intercom Appendix A Mounting the Intercom Appendix B Setting up a TFTP Server Page 1 Product Overview 1.1 Typical System Installation Figure 1-2.Typical Installation—MassNotification Figure 1-3.Typical Installation—EmergencyPhone 1.2 Product Features 1.3 Supported Protocols 1.4Supported SIP Servers 1.5 Product Specifications 2 Installing the VoIP Intercom 2.1 Parts List 2.2 Intercom Setup 2.2.1 VoIP Intercom Connections WIRE IN Accept Wire Range 4 From 16-26AWG 2.2.2 Connecting a Device to the Relay 2.2.3 Identifying the VoIP Intercom Connectors Figure 2-5.J2, J5, and J6 Connector Locations Figure 2-6.J1 and J7 Connector Locations Figure 2-7. JP11—RTFMSwitch Jumper See Table 2-2 for the connector settings Table 2-2.Connector Settings Jumper Setting 2.2.4 Call Button and Indicator Light 2.2.4.1 Initial Power 2.2.4.2 Calling 2.2.5 Network Connectivity, and Data Rate 2.2.5.1 Verify Network Activity 2.2.6 RTFM Switch Jumper 2.2.6.1 Announcing the IP Address 2.2.6.2 Restoring the Factory Default Settings 2.2.6.3Restore the Factory Default Settings 2.2.7 Adjust the Volume 2.3 Configure the Intercom Parameters 2.3.1Log in to the Configuration Home Page Figure 2-13.Home Page On the Table 2-5.Home Page Overview Web Page Item Description 2.3.2Configure the Network Parameters Table 2-6.Network Setup Parameters (continued) After changing the parameters, click Save Settings 4.Connect the Intercom to the target network 2.3.3Set up the Intercom 2.3.3.1Auxiliary Relay 2.3.4 Configure the SIP Parameters Table 2-8.SIP Setup Parameters (continued) 3. After changing the parameters, click Save Settings 2.4 Upgrade the Firmware and Reboot the Intercom 2.4.1 Reboot the Intercom Figure 2-19.Reboot System Section 2. Click Reboot. A normal restart will occur Appendix A: Mounting the Intercom A.1 Mount the Intercom Status Figure A-1.Network Connector Prior to Installation 4 x Mounting Screw Face Plate and PCB Assembly 2 Gang Box HOLE PLUG CONDUIT Page Page Appendix B: Setting up a TFTP Server B.1 Set up a TFTP Server B.1.1 In a LINUX Environment B.1.2 In a Windows Environment B.1.3 In a Solarwinds Server Environment Page Appendix C: Troubleshooting/Technical Support C.1 Frequently Asked Questions (FAQ) C.2 Documentation C.3 Contact Information C.4 Warranty Index Numerics