CyberData VoIP Intercom 47

user ID, SIP 22 username

changing for web configuration access 20 default for web configuration access 16 restoring the default 14, 16

verifying baud rate 11

intercom operations 20 network activity 12 network connectivity 11

warranty 36

web access password 14, 16 web access username 14, 16

web configuration log in address 16 web-based intercom configuration 16 weight 4

Windows, setting up a TFTP server on 33

yellow act light 12 yellow link light 11

Operations Guide

930181B

CyberData Corporation

Contents

Part #010935 PoE VoIP Intercom Operations Guide 930181B Part # COPYRIGHT NOTICE: © 2008, CyberData Corporation, ALL RIGHTS RESERVED Important Safety Instructions Pictorial Alert Icons Hazard Levels Revision History Page Contents Chapter 1 Product Overview Chapter 2 Installing the VoIP Intercom Appendix A Mounting the Intercom Appendix B Setting up a TFTP Server Page 1 Product Overview 1.1 Typical System Installation Figure 1-2.Typical Installation—MassNotification Figure 1-3.Typical Installation—EmergencyPhone 1.2 Product Features 1.3 Supported Protocols 1.4Supported SIP Servers 1.5 Product Specifications 2 Installing the VoIP Intercom 2.1 Parts List 2.2 Intercom Setup 2.2.1 VoIP Intercom Connections WIRE IN Accept Wire Range 4 From 16-26AWG 2.2.2 Connecting a Device to the Relay 2.2.3 Identifying the VoIP Intercom Connectors Figure 2-5.J2, J5, and J6 Connector Locations Figure 2-6.J1 and J7 Connector Locations Figure 2-7. JP11—RTFMSwitch Jumper See Table 2-2 for the connector settings Table 2-2.Connector Settings Jumper Setting 2.2.4 Call Button and Indicator Light 2.2.4.1 Initial Power 2.2.4.2 Calling 2.2.5 Network Connectivity, and Data Rate 2.2.5.1 Verify Network Activity 2.2.6 RTFM Switch Jumper 2.2.6.1 Announcing the IP Address 2.2.6.2 Restoring the Factory Default Settings 2.2.6.3Restore the Factory Default Settings 2.2.7 Adjust the Volume 2.3 Configure the Intercom Parameters 2.3.1Log in to the Configuration Home Page Figure 2-13.Home Page On the Table 2-5.Home Page Overview Web Page Item Description 2.3.2Configure the Network Parameters Table 2-6.Network Setup Parameters (continued) After changing the parameters, click Save Settings 4.Connect the Intercom to the target network 2.3.3Set up the Intercom 2.3.3.1Auxiliary Relay 2.3.4 Configure the SIP Parameters Table 2-8.SIP Setup Parameters (continued) 3. After changing the parameters, click Save Settings 2.4 Upgrade the Firmware and Reboot the Intercom 2.4.1 Reboot the Intercom Figure 2-19.Reboot System Section 2. Click Reboot. A normal restart will occur Appendix A: Mounting the Intercom A.1 Mount the Intercom Status Figure A-1.Network Connector Prior to Installation 4 x Mounting Screw Face Plate and PCB Assembly 2 Gang Box HOLE PLUG CONDUIT Page Page Appendix B: Setting up a TFTP Server B.1 Set up a TFTP Server B.1.1 In a LINUX Environment B.1.2 In a Windows Environment B.1.3 In a Solarwinds Server Environment Page Appendix C: Troubleshooting/Technical Support C.1 Frequently Asked Questions (FAQ) C.2 Documentation C.3 Contact Information C.4 Warranty Index Numerics