Manuals / D-Link / Computer Equipment / Switch

D-Link DES-5016 manual System Reset

Models: DES-5016

1 96

Download 96 pages 24.59 Kb

Page 51

Image 51

Fast Ethernet Switching System User’s Guide

System Reset

The System Reset panel, displayed in Figure 23, enables you to reset the DES-5016 without powering off.

Figure 23: System Reset

Some configurations will require you to reset the DES-5016 in order for them to take effect. Screen prompts will tell you to reset the DES-5016 as needed.

Follow these steps to reset the DES-5016:

1.Select Yes.

2.Press Enter.

To exit without resetting:

1.Select No.

2.Press Enter.

Managing the DES-5016

Page 51

Image 51

Contents

Rev. 01 January 651DES32.K15 DES-5016 Fast Ethernet Switching System User’s GuideD-Link Limited Warranty Hardware SoftwareCopyright 1999 by D-Link Systems, Inc. All rights reserved In the Middle East except Israel, Asia, Oceania and Africa D-Link Offices for Registration and Warranty ServiceIn North, Central, and South America In Europe and IsraelCopyright Statement FCC WarningCE Mark Warning Wichtige Sicherheitshinweise Table of Contents 100BASE-FX/ 1000BASE-SX Switch Port Module Connecting the DES-5016 to other Switches and HubsSystem Configuration Switch Port 1-8, 9-16 and Optional Module ConfigurationSpanning Tree Configuration Change PasswordSwitch Port Configuration Switch Port Configuration MenuAbout This Guide AudienceOrganization Introduction Features∙ VLAN support for eight broadcast domains Fast Ethernet Switching System User’s Guide∙ Supports Full and Half Duplex for both 10 Mbps and 100 Mbps ∙ The DES-5016 supports SNMP for RFC 1213, RFC 1757, and RFCDES-5016TX Front PanelDES-5016TF Figure 2 DES-5016TFFigure 3 DES-5016FX Figure 4 DES-5016 Rear Panel Rear PanelTelnet Management Management MethodsUpdating Firmware Local Console ManagementUnpacking the DES-5016 Installing the DES-5016Installation Options Figure 5 Install Feet on Bottom Desktop/ Shelf InstallationFast Ethernet Switching System User’s Guide Installing the DES-5016Figure 6 Attach Feet Figure 7 Attach Mounting Brackets Rack InstallationFast Ethernet Switching System User’s Guide Installing the DES-5016Figure 8 Insert into Rack Installing Optional Modules Fast Ethernet Switching System User’s Guide Installing the DES-5016Figure 9 Remove Blank Bracket Fast Ethernet Switching System User’s Guide Installing the DES-5016Figure 10 Insert Optional Module Power On Connecting the DES-5016 to the Network Cable SpecificationsCopper Cable Figure 11 Cable Diagram Fast Ethernet Switching System User’s GuideConnecting the DES-5016 to the Network Table 1 Cable Specifications for Copper ConnectionFiber Optic Cable RS-232 Port PortsMDI-X Ports Fiber Optic PortsDES-5016 to DES-5016 Connection Connecting the DES-5016 to other Switches and HubsFigure 12 DES-5016TF LEDs LEDsStatus PowerDiagnostic CPU ModuleTable 3 CPU Module LEDs Lit or FlashingDark Full/ Half 8-Port TX ModuleLink 100/10Table 4 8-Port TX Module LEDs Lit or FlashingDark Dark 8-Port FX ModuleLink/ Act Lit or Flashing2-Port 100BASE-FX Module Dark Fast Ethernet Switching System User’s GuideLEDs Table 6 FX Module LEDTable 7 Gigabit Module LED 1-Port 1000BASE-SX ModuleLink Figure 17 1-Port 1000BASE-SX ModuleManaging the DES-5016 ∙ User Name D-Link ∙ Default Password D-Link Local Console Management∙ Data bits ∙ Parity None ∙ Stop bits ∙ Flow Control None Telnet Log In ∙ Default User Name D-Link ∙ Default Password D-LinkFigure 19 Help Message Help MessagePanel Conventions Console Program System ConfigurationSwitch Port 1-8, 9-16 and Optional Module Configuration 100BASE-FX/ 1000BASE-SX Switch Port ModuleTrunking Port Management Spanning Tree ConfigurationSNMP Management Configuration VLAN Port ManagementSystem Information System Configuration MenuSystem Reset Factory Reset to Default Config ValuesHardware Revision Software UpdateBoot PROM Firmware Version System Information MenuSystem Name LAN Default GatewayMAC Address System DescriptionFigure 23 System Reset System ResetFigure 24 Factory Reset Factory ResetManaging the DES-5016 Fast Ethernet Switching System User’s GuideFigure 25 Factory Reset Confirmation 1. Select No or Exit 2. Press EnterSystem Rate Control Advantages of Store and ForwardDisadvantages of Store and Forward Disadvantages of Cut-Through Advantages of Cut-ThroughFigure 27 Software Update menu Software Update MenuFast Ethernet Switching System User’s Guide Managing the DES-5016Figure 28 Transfer Firmware Figure 29 Send File Figure 31 EEPROM Fast Ethernet Switching System User’s GuideManaging the DES-5016 Figure 30 XmodemUser Account Change Menu User Account ManagementCreate New User PasswordConfirm Password Access Level4. Toggle the space bar to set the access level of the new user Fast Ethernet Switching System User’s Guide2. Enter the Password 3. Reenter the password in the Confirm Password fieldAccess Level Delete UsersStatus Delete3. Select Save and press Enter Fast Ethernet Switching System User’s Guide2. Toggle the space bar to change the current Access Level 1. Select the Access Level of the user you want to deleteConfirm Password Change PasswordOld Password New PasswordFast Ethernet Switching System User’s Guide 5. Select Save and press Enter to save your changesManaging the DES-5016 Switch Port Configuration Switch Port Configuration Menu StatePhysical Port State PriorityFlow Control Spanning Tree Configuration Spanning Tree Configuration MenuSTA Operation Levels Root Cost Forward Delay TimeSpanning Tree Algorithm Bridge PriorityRoot Bridge Root PortTable 8 User Selective STA Parameters SNMP Management Configuration SNMP Community String SNMP Management Configuration MenuSNMP Manager Setting Access RightLink Change Event SNMP Trap Manager SettingAuthentication Failure Cold Start1. Enter the IP Address of the Trap Manager Fast Ethernet Switching System User’s GuideFollow these steps to configure the SNMP Trap Manager Setting 4. Select Save and press EnterVLAN Port Management Figure 39 VLAN Port Management menu VLAN Port Management MenuTrunkGroup Create New VLANNew VLAN Name Port #3. Select Save and press Enter Fast Ethernet Switching System User’s GuideFollow these steps to create a VLAN 1. Enter the name of the VLAN you are creatingFigure 41 Delete VLAN menu Delete VLAN MenuVLAN Name DeleteModify VLAN Menu Virtual LAN NameFigure 42 Modify VLAN menu Figure 43 Trunking Port Management menu Trunking Port Management MenuPort # Create New Trunking PortNew Trunking Group Name Name3. Select Save and press Enter Fast Ethernet Switching System User’s GuideFollow these steps to create a TrunkGroup 1. Enter the name of the TrunkGroupDelete Delete Trunking PortTrunking Port Modify Trunking PortFigure 46 Modify Trunking Port Trunking Port NamePOST Errors TroubleshootingProblem SolutionTroubleshooting Fast Ethernet Switching System User’s GuideFast Ethernet Switching System User’s Guide TroubleshootingTable 9 Diagnostic LED Appendix A DES-5016 Technical Specifications Switch SpecificationsPort Specifications Fast Ethernet Switching System User’s Guide ∙ Full or Half Duplex for all 10/100-TX portsAppendix A Fast Ethernet Switching System User’s Guide GeneralAppendix A Fast Ethernet Switching System User’s Guide Physical and EnvironmentalAppendix A Transmission Index