Datalogic Scanning 1000I EAN-8

Symbologies

5-12 Magellan® 1000i

EAN-8

The following options apply to the EAN-8 symbology.

Disable/Enable EAN-8

When disabled, the scanner will not read EAN-8 bar codes.

Check Digit Transmission

Enable this option to transmit the check Digit along with EAN-8 bar code data.

START / END

PROGRAMMING BARCODES

Disable EAN-8

Enable EAN-8

DEFAULT

START / END

PROGRAMMING BARCODES

Don’t Send Check Digit

Send Check Digit

DEFAULT

Contents

Main Page i-i Table of Contents i-ii Magellan 1000i Product Reference Guide i-iii i-iv Magellan 1000i Chapter 1 Getting Started About This Manual Manual Conventions 1-2 Connecting the Scanner NOTE Figure 2. Other Connection Types USB Connection Figure 1 Programming Using the Programming Bar Codes Resetting the Standard Product Defaults LED and Beeper Indicators Error Codes Page Chapter 2 General Features Double Read Timeout Double Read Timeout cont. Label Gone Timeout Productivity Index Reporting (PIR) Sleep Mode Sleep Mode cont. LED and Beeper Indicators Power On Alert Good Read: When to Indicate Good Read Beep Control This feature enables/disables the scanners ability to beep upon a successful decode of a bar code. Good Read Beep Frequency Good Read Beep Length Specifies the duration of a good read beep. Good Read Beep Volume Scanning Features Targeted Scanning Mode Target Mode Active Time Target Mode Linger Time Wake Up Intensity Wake Up Intensity cont. Chapter 3 Interface Related Features Page Interface Selection Page Page Page Interface Features Obey/Ignore Host Commands Interface Features cont. Host Transmission Buffers RS-232 Interface Features Page Hardware Flow Control Intercharacter Delay Intercharacter Delay cont. Software Flow Control Disables/Enables software control using XON/XOFF characters. Host Echo Host Echo Quiet Interval Host Echo Quiet Interval cont. Signal Voltage: Normal/TTL Specifies whether the RS-232 interface provides TTL levels on the output pins TxD and RTS. RS-232 Invert Beep on ASCII BEL Beep on Not on File ACK NAK Options RS-232 Interface Features cont. cont. ACK Character NAK Character Retry on ACK NAK Timeout ACK NAK Timeout Value ACK NAK Retry Count ACK NAK Error Handling Transmission Failure Indication IBM-USB Interface Features IBM-USB Device usage IBM IBM Transmit Labels in Code 39 Format Wand Emulation Supported Symbologies Wand Emulation Bar Code Format Bar/Space Polarity Wand Idle State Signal Speed Transmit Trailing Noise Transmit Leading Noise Symbology Conversion Keyboard Wedge USB Keyboard Page Caps Lock State Specifies the format in which the scanner sends character data. Page Page Page Page Chapter 4 Data Editing OR... Data Editing Overview Please Keep In Mind... Global Prefix/Suffix OR... Global Prefix/Suffix cont. AIM ID Label ID Page Page Page Page Page Case Conversion Character Conversion Chapter 5 Symbologies UPC-A Disable/Enable UPC-A Enable this option to transmit the check digit along with UPC-A bar code data. Expand UPC-A to EAN-13 Number System Transmission This feature enables/disables transmission of UPC-A System Number. UPC-A Minimum Reads UPC-A In-store Minimum Reads UPC-E Disable/Enable UPC-E UPC-E continued Number System Digit Expand to UPC-E to UPC-A UPC-E continued Expand UPC-E to EAN13 Page EAN-13 Disable/Enable EAN-13 EAN-13 continued EAN-13 Flag 1 Character ISBN Page EAN-8 The following options apply to the EAN-8 symbology. Enable this option to transmit the check Digit along with EAN-8 bar code data. Disable/Enable EAN-8 When disabled, the scanner will not read EAN-8 bar codes. EAN-8 continued Enable EAN Two-Label Enables/disables the ability of the scanner to decode EAN two-label pairs. Add-ons Contact Customer Support for advanced programming of optional and conditional add-ons. Add-ons continued RSS-14 Disable/Enable RSS-14 UCC/EAN 128 Emulation RSS-14 continued RSS Expanded Disable/Enable RSS Expanded UCC/EAN 128 Emulation Page RSS Expanded Length 1, Length 2 Programming Instructions Page Code 39 Disable/Enable Code 39 Check Character Calculation Start/Stop Characters Enables/disables transmission of Code39 start and stop characters. Code 39 Full ASCII Enables/disables the translation of Code 39 characters to Code 39 full-ASCII characters. Code 39 continued Code 39 Length 1, Length 2 Programming Instructions Quiet Zones Code 39 continued Code 39 Stitching Pharmacode 39 Disable/Enable Pharmacode 39 Start/Stop Characters Page Code 128 Disable/Enable Code 128 Transmit Function Characters Page Code 128 Length 1, Length 2 Programming Instructions Code 128 Conversion to Code 39 Code 128 Stitching Interleaved 2 of 5 Disable/Enable Interleaved 2 of 5 Check Digit Calculation Enable this option to transmit the check digit with scanned bar code data. Page Interleaved 2 of 5 Length 1, Length 2 Programming Instructions Interleaved 2 of 5 Stitching Page Codabar Disable/Enable Codabar Check Character Verification Page Page Codabar Length 1, Length 2 Programming Instructions Quiet Zones Start/Stop Character Type Codabar has four pairs of Start/Stop patterns. Select one pair to match your application. The transmission of start and end characters of Codabar is selected below. Start/Stop Character Transmission Start/Stop Character Match This feature enables/disables the requirement that start and stop characters match. Codabar Stitching Page Code 93 Disable/Enable Code 93 Page Code 93 Length 1, Length 2 Programming Instructions Code 93 Stitching MSI/Plessey The following options apply to the MSI/Plessey symbology. This feature specifies whether one or two check digits are to be calculated and verified. Disable/Enable MSI/Plessey When this feature is disabled, the scanner will not read MSI/Plessey bar codes. Number of Check Characters Page MSI/Plessey Length 1, Length 2 Programming Instructions MSI/Plessey Stitching Page Standard 2 of 5 The following options apply to the Standard 2 of 5 symbology. When enabled, the scanner will verify the check digit of the labels. Disable/Enable Standard 2 of 5 When this feature is disabled, the scanner will not read Standard 2 of 5 bar codes. When this option is enabled, the scanner will transmit the check digit. Page Standard 2 of 5 Length 1, Length 2 Programming Instructions Standard 2 of 5 Stitching Page Page Appendix A Product Specifications Optical and Read Performance Parameters Scanner Dimensions Physical Properties Electrical Parameters Other Parameters Environmental Parameters Appendix B Cable Pinouts IBM Port 5B/9B/17 Standard Cable Pinouts (Primary Interface Cables) RS-232 IBM USB USB & USB Keyboard Keyboard Wedge Wand Emulation Appendix C Alpha-Numeric Pad Alpha-Numeric Pad Appendix D Default Settings Defaults by Symbology The following is a partial list of key settings for each symbology type. Interface Default Exceptions IBM Interfaces IBM Interfaces include IBM-USB, IBM Port 9B, IBM Port5B and IBM Port17. RS-232 Wincor/Nixdorf Page Page Appendix E Keyboard Function Key Mappings Keyboard Model Cross Reference Page Page Page Page Page Appendix F Host Commands Accepting RS-232 Commands The scanner responds to the following RS-232 commands: Page Appendix G Sample Symbols Page ASCII Chart