Datalogic Scanning 6000 - page 7

Programming Guide 3

OCIA

• Datalogic OCIA

• NCR 8-Bit OCIA

• SNI OCIA

• NCR 9-Bit OCIA

RS-232

• Datalogic RS-232

• SNI RS-232

IBM

• IBM 4683/84, 4693/94 Port 5B

• 4682/92 Port E

• IBM 4683/84, 4693/94 Port 9A, 9B, 9C, 9E

Wand Emulation

Keyboard Wedge

• I/F Type A — PC/XT w/foreign keyboard

• I/F Type B — AT, PS/2 25-286, 30-286, 50, 50Z, 60, 70, 80, 90 &

95 w/foreign keyboard

• I/F Type C — PS/2 25 and 30 w/foreign keyboard

• I/F Type D — PC/XT w/US keyboard

• I/F Type E — AT, PS/2 25-286, 30-286, 50, 50Z, 60, 70, 80, 90 &

95 w/US keyboard

• I/F Type F — PS/2 25 and 30 w/US keyboard

• I/F Type G — IBM 3xxx w/122 keyboard

(QuickScan 6000 Plus ONLY)

• I/F Type H — IBM 3xxx w/102 keyboard

(QuickScan 6000 Plus ONLY)

• I/F Type I — PS/55 5530T w/104 keyboard

(QuickScan 6000 Plus ONLY)

• I/F Type J NEC 9801

(QuickScan 6000 Plus ONLY)

2. Turn to the appropriate page in this manual and enable the

desired interface or interface sub-type by scanning its pro-

gramming bar code. These interface/interface sub-type

selection bar codes are located at the beginning of each of

these sections of the manual: IBM, OCIA, Wand Emulation,

RS-232, and Keyboard Wedge. This will enable the software

for the new interface and disable the 'old' interface software.

Once enabled, the new interface becomes the default inter-

face that is active whenever power is applied to the scanner.

3. Scan a bar code to verify that the scanner communicates

correctly with the host system. Some sample bar codes are

provided on the last pages of this manual. If any changes to

the scanner's factory settings are needed, use the instructions

titled, Customizing Your Scanner Operation.

Contents

Main Page Contents Introduction------------------------------------------------------------------------ 1 ii Symbologies---------------------------------------------------------------------- 46 Appendix A Additional Information -------------------------------------------------------- 87 Appendix B Sample Bar Codes-------------------------------------------------------------- 88 Introduction Understanding the Basics Integrating Peripherals With Host Systems QuickScan 6000/6000 Plus Changing Interfaces Hardware Software Page 4 Customizing Your Scanner Operation Programming Overview What Is Programming Mode? How To Program Using Bar Codes The Programming Session Scanner Response When In Programming Mode If You Make a Mistake... Return to Factory Settings Where To Go From Here IBM 4683/84 4693/94 Port 5B Interface Selection TRANSMIT UNSOLICITED STATUS --- IBM 4683/84 4693/94 Port 9A, 9B, 9C, 9E I/F Selection TRANSMIT UNSOLICITED STATUS--- IBM 4682/92 Port E Interface Selection TRANSMIT UNSOLICITED STATUS--- Page OCIA Options Wand Emulation Interface Selection Programming Guide 15 TRANSMIT A NOISE ' C T S I RS-232 Interface Selection SNI RS-232 Interface Selection RS-232 Communication Parameters Page Page Handshaking Hardware Control CTS/RTS Flow Control CTS Scan Control Software Control C H RS-232 ACK/NAK Options (QuickScan 6000 Plus ONLY) Page Page Keyboard Wedge Communication Parameters PC Keyboard Wedge Interface Selection PC Keyboard Wedge Interface Selectioncontinued PC Keyboard Wedge Connect to a Laptop/No Keyboard Attached C LAPTOP/NO EXTERNAL KEYBOARD- KEYBOARD ATTACHED -------------- Caps Lock (QuickScan 6000 Plus ONLY) CAPS LOCK OFF------------------ CAPS LOCK ON ------------------- CAPS LOCK = SHIFT-LOCK-------- O L Country Mode (QuickScan 6000 Plus ONLY) Page Intercharacter Delay Page 32 Label Transmit Format Configuration Items (RS-232 and Keyboard Wedge Interfaces Only) Prefix & Suffix Page Non-Symbology Specific Items Setting Non-Symbology Specific Prefix(es) SET PREFIX ------------------------ Setting Non-Symbology Specific Suffix(es) SET SUFFIX ------------------------ Page Page ASCII Character Set Symbology-Specific Label I.D. Setting Symbology-Specific Label Identifiers (Label I.D.) Table 1. Industry Standard Label Identifiers (all are prefixes) Page Page Page How to Set Single Character Label I.D. Page Page Symbologies { INTERFACE TYPE KEY Symbology Options Overview Universal Symbology Selection Enable All Symbologies Disable All Symbologies Symbology Selection Page Page 52 UPC/EAN Options UPC/EAN Expansion UPC/EAN Add-Ons -O A D & F Price/Weight Check Digit QuickScan 6000/6000 Plus UPC-A determined by the UPC-A settings on this page, not by these settings. UPC-E Page 58 Code 39 Options Code 39 (continued) 60 Code 39 (continued) Page 62 Code 128 Options Interleaved 2 of 5 Interleaved 2 of 5 Label Lengths Check Digit and Variable Length Label Selections Setting Interleaved 2 of 5 Fixed and Minimum Label Lengths Page Standard 2 of 5 Standard 2 of 5 Label Lengths Check Digit and Variable Length Label Selections Setting Standard 2 of 5 Fixed and Minimum Label Lengths Page Page 72 Codabar Options Codabar Check Digit & Variable Length Codabar Start/Stop Character Codabar Fixed Length SET FIRST FIXED LENGTH --------- SET SECOND FIXED LENGTH ------ NO SECOND FIXED LENGTH ------- Page MSI/Plessey Check Digit S D MSI/P MSI/Plessey Fixed Length ENABLE MSI/PLESSEY FIXED----- DISABLE MSI/PLESSEY FIXED ---- L F MSI/P Page 80 General Features Good Read Beeper Settings Page Read Verification Universal Read Verification V R U Page Page Low Power Mode M LOW POWER IDLE ------------------ V ERY L OW P OWER M P Debug Mode M A AutoSense Stand Mode Appendix A Additional Information Appendix B Sample Bar Codes