Installing The Input/Output Panel | Dell 4691901 specification

7.Remove the Input/Output panel.

Related Links

Installing The Input/Output Panel

Installing The Input/Output Panel

1.Insert the Input/Output panel into the slot on the chassis front.

2.Slide the Input/Output panel towards the left of the computer to secure to the chassis.

3.Tighten the screw to secure the Input/Output panel to the chassis.

4.Connect the Input/Output panel or the FlyWire cable to the system board.

5.Install the front bezel.

6.Install the cover.

7.Follow the procedures in After Working Inside Your Computer.

Related Links

Removing The Input/Output Panel

Removing The Power Supply

1.Follow the procedures in Before Working Inside Your Computer.

2.Remove the cover.

3.Remove the PSU thermal sensor.

4.Disconnect the 4–pin power cable from the system board.

27

Image 27

Dell 4691901 owner manual Installing The Input/Output Panel, Removing The Power Supply, Remove the Input/Output panel

Contents

Regulatory Model D07D Regulatory Type D07D001 Dell Inc Contents Troubleshooting System Setup Contacting Dell SpecificationsPage Before Working Inside Your Computer Working on Your Computer After Working Inside Your Computer Turning Off Your Computer Installing The Cover Removing the CoverRelated Links Installing The Front Bezel Removing the Front BezelRemoving the Expansion Card Page Removing the Optical Drive Installing The Expansion Card Removing the Hard Drive Installing The Optical DrivePage Removing the Memory Installing The Hard Drive Removing the Chassis Intrusion Switch Installing The Memory Removing The Speaker Installing The Chassis Intrusion Switch Installing The Speaker Removing The Heat Sink and Processor Installing The Heat Sink and Processor Removing The Coin-Cell Battery Installing The Coin-Cell BatteryRemoving The Power-Switch Cable Installing The Power-Switch Cable Removing The Front Thermal Sensor Removing The System Fan Installing The Front Thermal Sensor Installing The System Fan Removing The Input/Output Panel Installing The System Fan Remove the Input/Output panel Installing The Input/Output PanelRemoving The Power Supply Disconnect the 4-pin power cable from the system boardPage Installing The Power Supply Remove the expansion cards Removing the System Board Installing the System Board Removing The PSU Thermal SensorRemove the system board from the chassis Installing The PSU Thermal Sensor CtrlAltF8 One-time boot and diagnostics utility menu F12 System SetupBoot Menu Boot Menu Enhancements Action Keystroke Beep Codes and Text Error MessagesTiming Key Sequences Navigation System Setup Options Security Password Changes Password BypassPassword prompts during a system restart They are set. This option is disabled by default Performance Power Management Virtualization Support Enable F12 Boot menu enabled by defaultMaintenance Post Behavior System Logs Diagnostic LEDs Diagnostic Light PatternsPower Button Troubleshooting Steps Possible system board failure has occurred Re-seat the 2x2 power connector from the power supply unitPower Button Problem Description If the problem persists, the system board is faulty Reinstalled all modules without error Problem Description Troubleshooting Steps Code Cause Microprocessor register failure Beep Codes Code Cause DMA initialization failure Code Through CauseCode Cause Code Cause Time-of-day clock stopped Error MessagesAddress mark not found Code Cause No time tick Shutdown failure Gate A20 failure Data error Alert! Security override Jumper is installedBad command or file name Bad error-correction code ECC on disk read Diskette read failure Diskette subsystem reset failedHard-disk drive configuration error Diskette drive 0 seek failure Keyboard failure Invalid configuration information-please run Setup programInvalid Memory configuration, please populate DIMM1 Memory allocation error Non-system disk or disk error No boot device availableNo boot sector on hard-disk drive No timer tick interrupt Time-of-day not set-please run the System Setup program Read faultReset failed Seek error \ is not accessible. The device is not ready Unexpected interrupt in protected modeWrite fault Write fault on selected drive Memory SpecificationSystem Information Processor Cards AudioNetwork Expansion Bus Audio Back Panel Mini-Tower/Desktop External ConnectorsSystem Board Connectors Mini-Tower Two Desktop One Small Form Factor Controls and Lights Environmental Physical Height Width Depth WeightPage Visit support.dell.com Contacting Dell